Harrod UK Aluminium Weighted Portagoal FBL-635 User manual

FBL-635
Aluminium Weighted Portagoal
INS582
Revison 9
19/11/2012
Harrod UK Limited©
View of Product
Fig 2
Assemble Flat
21
1
Fig 1
2
Inside
Inside
3
5
9
10
11
11
22
6
5
7
8
13
25
24
4
4
14
15
16
17
18
19
20
23
24
25
14
22
Code:
Product:
Pack Contents:
1. 2 x Crossbar. (FEQ330)
2. 2 x R/H Painted Upright. (PEQ334)
3. 2 x L/H Painted Upright. (PEQ333)
4. 4 x Net Support. (PEP343)
5. 4 x Elbow Brace. (PEQ336)
7. 4 x Internal Corner Plate. (PLT076)
. 4 x Internal Corner Box. (WEQ337)
10. 4 x External Corner Bracket. (PLT085)
11. 2 x Sidebar Assembly (pair). (FEQ710)
12. 2 x Axle Bar. (FEQ308)
13. 24 x Roller Tube. (STE029)
6. 4 x Spacer Block. (APP150)
8. 4 x External Corner Plate. (APP105)
9
14. 4 x Handle. (PEP499)
15. 2 x Wheel Assembly Pair. (FPK620)
16. 140 x Plastic Net Hooks. (HKS029)
17.
18.
19. 40
20.
21. 4 x M10 x 80mm Hex Bolt. (BOL280)
22. 4 x Net Support Spacer (APP485)
23. 4 x 70mm Diameter Collar. (PLT346)
24.
25.
26. 1 x Back Bar (Pair) (FEQ800)
27. 4 x Weighted Back Bar Bracket (PEQ375)
28. 4 x M8*50 Hex Bolt Stainless (BOL509)
29. 4 x M8 Nylock Nut BZP (BOL402)
30. 12 x M10 Binx Nut (BOL201)
52 x M10 BZP Nyloc Nut. (BOL202)
56 x 10mm Washer. (BOL709)
x M10 Square Head Bolt. (BOL336)
4 x M10 x 50mm Hex Bolt. (BOL306)
4 x Plastic Slim Axle Bush. (PLA121)
48 x Plastic Axle Bush. (PLA120)
30
27
27
26
Tools Required
2 x 17mm Spanners
1 x Pair Scissors
1 x Mallet
IMPORTANT PLEASE READ THE
ASSEMBLY INSTRUCTIONS
CAREFULLY BEFORE STARTING
TOASSEMBLEYOUR GOAL

FBL-635
Aluminium Weighted Portagoal
This product is protected by © Copyright
and Design Right Harrod UK Ltd 2003.
Code:
Product:
Assembly Instructions
1
6
Please Note: For safety reasons, It is recommended that two or more people assemble this goal.
Fig.3
Fig.4
170
650
Fig.5
Fig.6
Fig.7
Warning: the force on each handle to move the goal is equivalent to 34Kg, therefore 4 People are required to move this goal.
Referring to instruction number INS565 (provided with the Wheel Assemblies) lift the Goal onto the Wheel Assemblies. The
Backbar acts as a Roller so that the Goal can be by 4 people pulling on the handles.manoeuvred
Operating Instructions
2
2
21
15 14
10
23
17
12
25
13
11
11
11
9
7
8
20
19
5
18
17
4
3
3
1
2
4
7
Identify the parts using the Pack Contents and Fig 1 overleaf. The Goal will be
initially assembled flat on the ground in 2 halves as shown in Fig 2.
- Lay the Crossbar (1) and Uprights (2 & 3) on the ground
with the slots facing upwards and Slide 3 Square Head Bolts (19) into to the slots at
both ends of the Crossbar, and 2 Square Head Bolts into the end of each Upright.
Fit the large ‘L’ Shaped Internal Corner Plates (7) into the ends of the Crossbar and
Uprights and slide them together. Fit the External Corner Plates (8) and net supports
(4) onto the Bolts in the Crossbar and the Uprights and secure with Washers (18) and
Nuts (17). Fit the Elbow Braces (5) between the Net Supports and the Crossbar with the
Spacer Blocks (6) and Secure with a 50mm Bolt (20), Washers (18) and Nuts (17), all as
shown in Fig 3.
- Position a Collar (23) in between the Axle Bracket Lugs
on one of the Side Bar Assemblies (11) and Insert theAxle Bar (12). Lock the end in
place with an 80mm Bolt (21) and Nut (17) as shown in Fig 4.
With a PlasticAxle Bush (25) inserted into the ends of a Roller Tube (13), slide over
the open end of the Axle Bar. In between every 4 of these Roller Assemblies slide a
Plastic Slim Axle Bush (24) (see Figs 1 & 4). When the Axle Bar is full, fit the other
Sidebar Assembly onto the open end of the Axle Bar and secure in the same way as in
Step 4.
- Fit the Wheel (15) and Handle (14)Assemblies to
each Side Bar following the Instructions included with these products, however
position them to the dimensions shown in Fig 5.
- Insert one
n Internal Corner Box (9) into the open end of
each Upright. Lift the whole Upright and Crossbar into the vertical position and slide
the Internal Corner Box previously fitted into the Sidebar. Secure together by fitting the
External Corner Bracket (10) with Washers and Nuts as shown in Fig 6.
Crossbar and Uprights
Backbar and Sidebars
Wheel and HandleAssemblies
Joining the 2 Halves
3
6
5
Square Head Bolt into the slot of each open end of
the Uprights and Sidebars. Insert a
Place the net support spacer onto the factory-fitted Square Head Bolts in the Sidebar
and position so that the protruding screws in the underside of the plates sit one each
side of the end pre-fitted Cap Head Screw. Place the end of the Net Supports over the
Square Head Bolts and then place the bracket (27) over the bolts so that it is facing in to
the goal (as shown in Fig 7)
. (Supplied Separately)
Attach the hooks to the net approx 250mm apart, then insert the hook into the slot on
the goal section and twist to lock.As a guide you should fit 30 to the Crossbar and 10
to each Upright and each Sidebar.
To attach the net at the bottom simply thread the bar through alternative meshes on
the last row of the net and insert the bar into the bracket as shown in Fig.7
8
Fitting The Net
1
2