HARTINGTON FLORENCE Hanging Chair User manual

Important
Please read these instructions before using the product. Retain instructions for future use.
HHGL Limited, MK9 1BA. HHGL (ROI) Limited, D02 X576
HARTINGTON
Hanging Chair
Powder-coated steel frame
Made of PE rattan
H197.5 x W116 x D118cm
FLORENCE COLLECTION

2
SAFETY & CARE ADVICE
IMPORTANT INFORMATION
Please read these instructions fully before starting assembly.
• Check you have all the components and tools listed in this booklet before assembly.
• Remove all fittings from their plastic bags and separate them into their groups.
• Keep children and animals away from the work area; small parts could choke if swallowed.
• Make sure you have enough space to lay out the parts before starting.
• Do not stand or put weight on the component parts during assembly, as this could cause damage.
• Assemble on a soft, level surface to avoid damaging the unit or your floor.
• We recommend a two-person assembly.
• Dispose of all packaging carefully and responsibly.
• Do not tighten screws completely until assembly is complete. Then place the bolt caps and nut caps
on all visible bolts and locknuts.
• Regularly check all the bolts, screws and fastenings are secure.
• Only clean using a damp cloth and mild detergent; do not use bleach or abrasive cleaners.

R
u le r - U s e th is ru le r to h e lp corre ctly i
de n tify th e s cre w s
0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 75 80 85 90 95 100 110 115 120 125 130 135 140 145 150 155 160 165 170
105
3
COMPONENTS - FITTINGS
Please check you have all fittings listed
below. If you have any missing or
damaged fittings, please contact your
local store.
Note: The quantities below are the correct
amount to complete the assembly. In some
cases, more fittings may be supplied than
required.
Tools included
Please check you have all components
listed below. If you have any missing or
damaged components, please contact
your local store.
COMPONENTS - PANELS
A
Leg
Leg
Leg
B
C
1
1
2
1
1
1
D
E
F
G
H
I
1
1
1
Pole
Pole
Basket
Basket
Chain
Metal plug
2
Spanner
86
16
8
14
112
AA BB
CC DD
EE FF
GG HH

ASSEMBLY INSTRUCTIONS
Step 1
Attach leg (A) to leg (C) with bolts (BB) and flat washers (DD) using spanner (II).
Step 2
Attach leg (B) to leg (C) with bolts (BB) and flat washers (DD) same as above.
Attach leg (B) to leg (A) with bolts (EE), locknut (GG) and flat washers (HH) using spanner (II).
Step 3
Attach pole (D) to the base with bolts (FF) and flat washers (DD) using spanner (II).
AC
BB
DD
BB
DD
C
C
B
HH
GG
HH
EE
D
FF
DD

ASSEMBLY INSTRUCTIONS
Step 4
Attach hanging pole (E) to pole (D) with bolts (AA), locknut (CC) and flat washers (DD) using spanner (II).
Insert metal plug (I) into the hole at the top of the pole. Place the assembled frame on a flat surface.
Step 5
Attach basket (F) to (G) with bolts (EE), locknut (GG) and flat washers (HH) using spanner (II).
Hanging the assembled basket to the pole with stainless steel chain (H), adjust the length of the chain to the desired
height.
ASSEMBLY COMPLETE
I
EAA
DD
DD
CC
F
G
H
GG HH
HH EE