Fisher-Price M0324 User manual

www.fisher-price.co.uk
WARNING
IMPORTANT! PLEASE KEEP FOR
FUTURE REFERENCE.
M0324

Seat Pad
#6 x 3 cm (13
/16 ") Screw – 2
IMPORTANT! Please remove all parts from the
package and identify them before assembly.
Some parts may be packed in the pad.
Note: Tighten or loosen all screws with a Phillips
screwdriver. Do not over-tighten the screws.
Seat Frame
2
To prevent serious injury or death
from falls and being strangled in the
restraint system:
• Always use the restraint system.
• Not recommended for children who
sit up by themselves (6 months
approximately, until 9 kg/20 lbs).
• Never leave child unattended.
• It is dangerous to use this product on
an elevated surface.
WARNING
CAUTION
This package contains small parts in its
unassembled state. Adult assembly
is required.
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.
©2007 Mattel, Inc. All Rights Reserved. PRINTED IN CHINA
® and ™ designate U.S. trademarks of Mattel, Inc. M0324pr-0726
2 Swing Frames
2 Base Tubes
Shown Actual Size
• Please read these instructions before assembly and use of
this product.
• Adult assembly is required. Tool needed for assembly:
Phillips Screwdriver (not included).
• Requires four LR14 ("C") alkaline batteries for operation
(not included).
• Weight Limit: 9 Kg (20 lbs).
IMPORTANT! The maximum weight limit for this product
is 9 kg (20 lbs). If your child weighs less than 9 kg (20 lbs),
but is really active, and appears to be able to climb
out of the swing, immediately discontinue its use.
• Product features and decorations may vary from photo.
Consumer Information Parts
Great Britain: Mattel UK Ltd. Vanwall Business Park, Maidenhead
SL6 4UB. Helpline: 01628 500303; www.service.mattel.com/uk.
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag
#870, Richmond, Victoria 3121 Australia. Consumer Advisory Service
1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower,
World Finance Centre, Harbour City, Tsimshatsui, HK, China.
Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.
(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran
Tropicana Golf Country Resort, 47410 PJ. Tel: [phone],
Fax: [phone].
2 Toys
(Toys may be different)

3
Assembly
Swing Frame Front Leg
Swing Frame Back Leg
• Slide the front and back legs on the swing frame outward
until they “click” into place.
• Repeat this procedure to open the other swing frame.
Base Tube
Press Buttons
on Front Legs
• While pressing the buttons on the end of each front leg,
insert the front legs into the ends of one of the base tubes.
• Push the front legs down into the base tube until the
buttons “click” into place.
IMPORTANT! Before assembly, inspect this product for damaged
hardware, loose joints, missing parts or sharp edges. DO NOT use if
any parts are missing or broken. Contact Mattel for replacement
parts and instructions if needed. Never substitute parts.
Base Tube
PULL UP
• While standing on the base tube, pull the front legs up. The
front legs should remain secured to the base tube. If you can
remove the front legs, you have not assembled them correctly to
the base tube. Re-read and repeat assembly step 2.
Base Tube
Press Buttons
on Back Legs
• While pressing the buttons on the end of each back leg, insert
the back legs into the ends of the remaining base tube.
• Push the back legs down into the base tube until the buttons
“click” into place.
1
3
2
4

4
• Position the seat frame so that the tubes are upright,
as shown.
Hint: Note the location of the socket inside each seat hub. The ends of the
frame arms will be inserted into these sockets.
• Fit the end of each frame arm into the socket in each seat hub.
Base Tube
Assembly
• While standing on the base tube, pull the back legs up. The back
legs should remain secured to the base tube. If you can remove
the back legs, you have not assembled them correctly to the
base tube. Re-read and repeat assembly step 4.
PULL UP
Frame Arm
Frame Arm
Seat Frame
Seat Hub
Seat Hubs
Socket
Seat Hub
Seat Hub
• Insert a 3 cm screw through the outside of each seat hub and
into each frame arm. Tighten the screws.
• Fit the pad upper pocket over the seat back tube.
• From behind the assembly, insert the waist belts through the
slots in the pad.
• Press to fasten the waist belt assembly to the pad.
Seat Back Tube
Pad Upper Pocket
Waist Belts
Waist Belt
Waist Belt
Slots
Slots
Waist Belt
Fasteners
Slots
5
6
7
8

5
Assembly Battery Installation
Battery Safety Information
• Fit the pad lower pocket onto the seat bottom tube, as shown.
Assembly is now complete.
Pad Lower Pocket
Seat Bottom Tube
Hint: We recommend using alkaline batteries for longer battery life.
1,5V x 4
LR14 (“C”)
Note: Low battery power may cause product movement to slow
and sound volume to become faint or turn off all together. If this
should happen, please remove and discard all four batteries and
replace with four, new LR14 (“C”) alkaline batteries.
• Locate the battery compartment door on the frame.
• Loosen the screws in the battery compartment door.
• Remove the battery compartment door.
• Insert four "C" (LR14) alkaline batteries.
• Replace the battery compartment door and tighten the screws.
Battery Compartment Door
In exceptional circumstances, batteries may leak fluids that
can cause a chemical burn injury or ruin your product.
To avoid battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable
(nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of this product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removeable, rechargeable batteries are used, they are only to
be charged under adult supervision.
9

6
Securing Your Child
To prevent serious injury or death
from falls and being strangled in
the restraint system:
• Always use the restraint system.
• Not recommended for children who
sit up by themselves (6 months
approximately, until 9 kg/20 lbs).
• Never leave child unattended.
• It is dangerous to use this product on
an elevated surface.
WARNING
Waist Belt
Restraint Pad
Buckle
• Place your child in the seat. Position the restraint pad between
your child’s legs.
• Fasten both waist belts to the buckles on each side of the
restraint pad. Make sure you hear a “click” on both sides.
• Check to be sure the restraint system is securely attached
by pulling it away from your child. The restraint should
remain attached.
IMPORTANT! The maximum weight limit for this product is 9 kg
(20 lbs). If your child weighs less than 9 kg (20 lbs), but is really
active, and appears to be able to climb out of the swing,
immediately discontinue its use.
Free End
TIGHTEN


Anchored EndAnchored End
To tighten the belts: Feed the anchored end of the belt up
through the buckle to form a loop . Pull the free end of the
belt . Repeat this procedure to tighten the other belt.
To loosen the belts: Feed the free end of the belt up through the
buckle to form a loop . Enlarge the loop by pulling on the end
of the loop toward the buckle. Pull the anchored end of the belt
to shorten the free end of the belt . Repeat this procedure to
loosen the other belt.
Please Note: After adjusting the belts to fit your child, make sure
you pull on them to be sure they are securely fastened.
Free End

LOOSEN

7
IMPORTANT! Before each use, inspect this product for damaged
hardware, loose joints, missing parts or sharp edges. DO NOT use if
any parts are missing or broken. Contact Mattel for replacement
parts and instructions if needed. Never substitute parts.
Power Switch
• Slide the power switch to any of five speed settings.
• Give the seat a light push to start the swinging motion.
Adjust the power switch to the desired swing motion setting.
Hint: As with most battery-powered swings, a heavier child will reduce the
amount of swinging motion on all settings. In most cases, the low
setting works best for a smaller child while the high setting works best
for a larger child.
• If swinging stops while using a lower setting, try a higher
setting. Give the seat a light push to start the swinging
motion again.
• Be sure to turn this product off when not in use. Slide the
power switch to the off setting .
• For baby's enjoyment, attach the toys to the toy rings on
the hubs.
Starting the Swing Room-to-Room Portability
• Make sure your child is properly secured in the swing seat.
• Grasp both handles on the top of the swing and lift.
• Carefully carry the swing to another room. Be sure to set the
swing down on a non-elevated, flat surface.

8
• Lift the seat bottom.
LIFT
PRESS
• Press the frame release buttons on the inside of the frames and
push the front legs inward.
• Press the frame release buttons on the inside of the frames and
push the back legs inward.
The pad and soft toys are machine washable. Place the soft toys
in a pillow case. Wash the pad and toys separately in cold water
on the gentle cycle. Do not use bleach. Line dry. The frame can be
wiped clean using a mild cleaning solution and a damp cloth.
Do not immerse the frame.
To remove the pad:
• Lift the footrest and remove the pad lower pocket.
• Push the waist belts back through the pad.
• Slide the pad upper pocket off the seat back tube.
To re-assemble the pad:
• Refer to assembly steps 8 and 9.
Storage Care
• Protect the environment by not disposing of
this product with household waste (2002/96/EC).
Check your local authority for recycling advice
and facilities (Europe only).