Hathaway BG2233BL User manual

SURE SHOT DUAL ELECTRONIC
BASKETBALL GAME
ASSEMBLY INSTRUCTIONS
BG2233BL
Please Do Not Hesitate to
Contact Our Consumer Hotline
at 800-759-0977
with Any Questions That May
Arise During Assembly or
Use of This Product!
Ver. 0320

THANK YOU!
Thank you for purchasing this product. We work around the clock and around the globe to ensure
that our products maintain the highest possible quality. However, in the rare case of issues during
assembly or use of this product, please contact our Consumer Hotline at 800-759-0977 for immediate
assistance before contacting your retailer. Please read the warranty information at the back of these
assembly instructions for further details.
2
CARE AND USE
1. This product is intended for INDOOR use only.
2. Do NOT drag the chair when moving it, as this will damage the legs.
ASSEMBLY TIPS
1. Find a clean, level surface to begin the assembly of your game table. We recommend that two adults
work together to assemble this game. You may want to carefully cut or tear the four corners of the box
so that the bottom of the box can be used as your work surface.
2. Remove all of the contents from box and verify that you have all of the parts shown on the Parts
List before you begin assembly. Note: Some parts may be pre-installed or pre-assembled.
3. Some figures or drawings may not look exactly like product.
4. When installing parts that have more than one screw or bolt, hand tighten all screws or bolts
in place before final tightening with screwdriver or wrench.
5. Electric screwdrivers may be helpful during assembly; however, please set a low torque and use
extreme caution because screws may be stripped or overtightened, resulting in damaged parts, if the
electric screwdriver’s torque is set too high.
WARNINGS!
READ AND FOLLOW ALL ASSEMBLY, OPERATION AND SAFETYINSTRUCTIONS CAREFULLY.
CHOKE HAZARD - THIS ITEM MAY CONTAIN SMALL BALLS AND PARTS
NOT SUITABLE FOR CHILDREN UNDER 3 YEARS OF AGE.
IMPORTANT! PLEASE READ THESE ASSEMBLY INSTRUCTIONS
IN ENTIRETY BEFORE ASSEMBLING YOUR PRODUCT.

3
HOME VISITOR
TIME
910 11 12
13 14 15 16
Switch Sensor Control Box with WireElectronic Scorer
2 3 4
x2 x2 x1 x1
6 7 85
x1 x2 x2
x2 x2 x1 x2
x4 x1 x2 x1
x1
Rim
18 19 20
Inflation Pump with NeedleRim Support Plate
x2 x1
21
Backboard
x1
M6 Washer
22
x64
M6 x 20mm Bolt
23
x16
M6 x 30mm Bolt
24
x6
25
M6 x 42mm Bolt
x4
M6 x 48mm Bolt
26
x4
M6 x 35mm Bolt
27
x2
M6 Nut
28
x32
29
3.5 x 10mm Screw
x4
4 x 28mm Screw
x2
Electronic Scorer Face Plate
30
x1
Basketball
7" Dia.
31
Wrench
32
x1
17
x2
End Cap
x2
Tube 1
Ø22x580x440mm Tube 2
Ø22x685mm Tube 3 Ø22x890mm Tube 4 Ø22x890mm
Tube 7
Ø22x830mm Tube 8 Ø22x835mm
Ø12.7x1070mm
Ø22x740mm
Tube 5
Ø22x755x580mm Tube 6 Ø22x755x580mm
Ø22x540x385mm Ø22x1065x520mm
1NGP6020
NGP6034
NGP6023
NGP6033
NGP6024
NGP6022
NGP6027
NGP6021
NGP6028
NGP6026
NGP6031
NGP6025
NGP2217
NGP6030
NGP6035
NGP6029
NGP6036 NGP6038 NGP6039NGP6037
NGP6040 NGP6041* NGP6041*NGP6041*
NGP6041* NGP6041* NGP6041*NGP6041*
NGP56431** NGP6042 NGP6041*NGP6041*
Tube 11 Tube 12
Tube 9 Tube 10
*Items included in Hardware Pack, NGP6041
**Item included with Electronic Scorer, NGP6033
01/18 For replacement parts please call 800-759-0977.
SURE SHOT DUAL ELECTRONIC BASKETBALL - BG2233BL
Parts List

PARTS IDENTIFIER (NOT TO SCALE)
4
For replacement parts please call 800-759-0977.
33
Allen Key
x1
34
Ball Return Net
x1
35
Lock Pin
Net Spring Lock Plastic Pole Insert
A1 A2
x2 x2
Self-Stick Strap
x2
x9 x2
A3 A4
PRE-INSTALLEDPARTS
Power Tools
-Set Low Torque
High Torque
over tightened
X2
Strong Adults Needed No Children in
Assembly Area
Keep away from pets Do not use or keep product
outdoors. For indoor use only.
No wet/humid conditions.
TOOLS REQUIRED
• Phillips Screwdriver - Not included
• Standard (Flat Head) Screwdriver - Not included
• Allen Wrench - Included
Electric Screwdrivers may be helpful during assembly;
however, please set a low torque and use extreme caution.
CAUTION!
NGP6043 NGP6044NGP6041*
*Items included in Hardware Pack, NGP6041
1/18
NGP60361

THANK YOU!
5
ASSEMBLY INSTRUCTIONS
FIG. 1 & 2
1. Attach Tubes 2 (#2) to Tube 3 and Tube 4 (#3 & #4) using spring lock (pre-installed) as shown in FIG.1.
2. Attach Tubes 7 (#7) to Tubes 8 (#8) using spring lock (pre-installed) as shown in FIG.2
2
2
2
3
3
4
4
7
8
X 2
X 1
X 1
X 2
X 2
FIG. 1 FIG. 2
Punched hole
7
8
A2
Spring Lock
A2
Spring Lock
FIG. 3
A2
Spring Lock
5
6
5
6
X 1
X 1
FIG. 3
3. Attach Tube 5 and Tube 6 (#5 & #6) together using spring lock (pre-installed) as shown in FIG.3.

FIG. 4
4. Attach Tube 5 and Tube 6 (#5 & #6) to Tube 3 and Tube 4 (#3 & #4) using Bolts (#26), Washers (#22) and Nuts (#28),
and then attach Tube 5 and Tube 6 (#5 & #6) to Tubes 8 (#8) using Bolts (#26), Washers (#22) and Nuts (#28) as shown
in FIG. 4, 4A and 4B.
5. Attach Tubes 7 and Tubes 8 (#7 & #8) to Tube 2 (#2) using Bolt (#24), Washers (#22) and Nuts (#28) as shown in
FIG. 4C, repeat this step for other side. NOTE: Make sure the spring lock is facing down.
ASSEMBLY INSTRUCTIONS (CONT.)
6
22
24
26
28
X 12
X 2
X 4
X 6
FIG. 4
5
3
4
2
8
86
7
7
2
FIG. 4A
26
28
22
22
FIG. 4B
22 26
22
28
FIG. 4C
22
22
28
24

FIG. 5
6. Attach Tube 12 (#12) to Tubes 2 (#2) using Bolts (#24), Washers
(#22) and Nuts (#28) as shown in Fig. 5A, and then insert Tubes 1
(#1) onto Tubes 2 (#2) as shown in FIG. 5.
7. Attach Tubes 9 (#9) to Tube 5 and Tube 6 (#5 & #6) using Bolt (#27),
Washers (#22) and Nuts (#28) as shown in FIG. 5 and 5B
ASSEMBLY INSTRUCTIONS (CONT.)
7
1
9
12
22
24
27
X 2
X 2
X 1
X 8
X 2
X 2
28
X 4
FIG. 5
1
FIG. 5A
12
12
2
2
1
1
2
24
28
22
22
9
5
6
9
28
22
22
27
FIG. 5B
A3

FIG. 6
8. Attach Tubes 10 (#10) to Tubes 9 (#9) using
spring locks (pre-installed), and then insert Tube 11 (#11)
onto Tubes 10 (#10) using spring locks (pre-installed) as shown in FIG. 6.
ASSEMBLY INSTRUCTIONS (CONT.)
8
10
FIG. 6
9
9
Long
Short
10
10
X 2
11
X 1
11
10
11
A2
Spring Lock
A2
Spring Lock

THANK YOU!
9
ASSEMBLY INSTRUCTIONS (CONT.)
FIG. 7
9. Attach Rims (#17) and Rim Support Plates (#18) to the Backboard (#21) using the Bolts (#23), Washers (#22) and
Nuts (#28). Attach the Switch Sensors (#15) to the Backboard (#21) using the Bolts (#23), Washers (#22) and Nuts (#28).
NOTE: Make sure that you use washer on both sides of the backboard as shown in FIG. 7.
FIG. 8
10. Attach the Electronic Scorer Face Plate (#31) to the front of Backboard and connect with the Electronic Scorer (#14)
using Bolts (#29) as shown in FIG. 8.
FIG. 7
28
15
15
17
17
22
22
23
23
28
22
22
18
18
21
15
17
18
21
22
23
28
X 2
X 2
X 2
X 1
X 32
X 16
X 16
FIG. 8
TIME
VISITOR
HOME
29
14
31
14
29
31
X 1
X 4
X 1
HOME VISITOR
TIME

FIG. 9
11. Slide elastic straps and sleeve of Ball Return Net (#35) onto Top Tubes 1 (#1) as shown in FIG. 9A & 9B.
12. Slide Tube 12 (#12) through the sleeve on the front of the Ball Return Net (#35), attach the left side first using
Bolts (#24), Washers (#22) and Nuts (#28) as shown in FIG. 9C. Follow the same procedure on the right side.
ASSEMBLY INSTRUCTIONS (CONT.)
10
X 1
X 4
X 2
X 2
12
12
12
X 1
35 35
35
22
22
22
22 22
24
24
24
24
28
28
28
28
11
11
12
FIG.9
FIG.9A
FIG.9B
FIG.9C
A4
Lock Pin