Havis C-DMM-3011 User manual

C‐DMM‐3011_INST_3‐19


TOOLSREQUIRED:
•RatchetWrench •SocketSet •7/16”OpenEndWrench•T‐20Torxbit
•PhillipsScrewdriver(short) •Dashpanelremovaltool•Wirestripers/cutters
Notes:
1. TheC‐DMM‐3000swivelplateacceptsC‐MM‐301offsetbracketusedwithC‐MM‐2XXadaptors.
2. C‐MM‐2XXseriesadaptorbracketsarenotneededformostVESA75andotherHavisDocking
Stationmountingapplications.
3. CM009068VESArotatorplategivesadditionalpositioningoptions,butisnotrequired
dependingonmountingpreference.
4. DoesNOTworkwith8.4”,12”displaysorotherradioswiththefollowingSalescodes:
UAS,UAM,UAQ,UAVandUAX
ALWAYS!
ReadallinstructionsbeforeinstallinganyHavis,Incproducts.
Usehardwareprovidedwithinstallkit
INSTALLATIONINSTRUCTIONS
C‐DMM‐3011FlipupDashMonitorMount
2013‐2019Ram1500SpecialServicesPolice&1500TradesmanPickupTruckwith"Classic"Bodystyle
2013‐2019Ram1500,2500,3500RetailPickupTruckwith"Classic"Bodystyle

**Compatiblewith3‐Inchand5‐InchRadioDisplayONLY(SalescodesRA1,UA1,RA2,UAA)**
HARDWAREandPARTS:
QTYDESCRIPTIONPART#
1DriversidemountCM009612
1PassengersidemountCM009613
2SidesupportbracketCM009614
1VESArotatorplateCM009068
1PVCwasherCM008582
2 1/4"Plasticflatwasher   CM86600
4 1/4"NylocknutGSM30016
4 1/4"Steelflatwasher   GSM31005
41/4"Starwasher   GSM31035
41/4"x1/2"Phillipspanheadbolt GSM33123
41/4"x1/2"Flatheadbolt  GSM34057
21/4"x3/4"Hexheadbolt  GSM33001
48‐32KepsnutGSM30027
1Loctite(removablemediumstrength)GSM20075


C‐DMM‐3011_INST_3‐19
CM009612
Driverside
Mount

CM009068
VESArotator
plate
CM008582
PVCwasher
C‐DMM‐3011
Assembly
GSM34057‐1/4"x1/2"Flatheadbolt
GSM20075‐Loctite
CM009613
Passengerside
Mount
CM86600‐ 1/4"Plasticwasher
GSM31005‐1/4"Steelwasher
GSM30016‐1/4"Nylocknut
CM009614
Sidesupportbracket
(Oneeachside)
GSM30027
8‐32Kepsnut
GSM33123 ‐1/4"x1/2"Panheadbolt
GSM3103‐1/4"Starwasher
Frameandhinge
mountassembly
GSM33001
1/4"x3/4"Hexbolt
GSM30016
1/4"Nylocknut
GSM31005
1/4"Flatwashers
(Notshown)

C‐DMM‐3011_INST_3‐19


Removerubberlinerandremovescrewsin
uppercentercointray.(T20Torxbit)
Removescrewinlowerrightdashpocket.
(T20Torxbit)
DodgeRamPickupdash with Uconnect®3
Radiowith5‐InchDisplaypriortoinstallation.
Removerubberlinerinlowerrightdashpocket.

Removeradiomountscrews,unplugand
removeradiocontrol.(7mmsocket)
Carefullypartiallyremovecenterinstrument
panel.Thisdoesnotneedtobeunplugged.

C‐DMM‐3011_INST_3‐19


Attachdriverandpassengersidemountbrackets
toinnerOEMframewith1/4"x3/4"hexhead
bolts,flatwashersandnylocknuts.
Tightenmountbrackethardware. Snapcenterinstrumentpanelbackintoplace.
Mountbracketswillcomeoutthroughsidesof
radioopening.
Looselyattachdriverandpassengersidemount
brackets(CM009612&CM009613)toradiomount
holes with OEM radio mount
screws.
Reattachuppercointrayandlowerdash
pocketwithpreviouslyremovedscrews.
Attachsidesupportbrackettodriversidemount
bracketwith1/4"x1/2"flatheadbolts.
Note:UseadropofLoctiteoneachbolt.

C‐DMM‐3011_INST_3‐19



Placeframe&hingeassemblyontosupportbrackets
andmakesureitfitsaroundradioproperly.
Attachsidesupportbrackettopassengerside
mountbracketwith1/4"x1/2"flatheadbolts.
Note:UseadropofLoctiteoneachbolt.
Attachframewith1/4"x1/2”panhead
boltsandstarwashers.Driversideshown.
Plugradiobackinandattachtosupportbrackets
with8‐32Kepsnuts.(11/32”socket)
AttachVESAplatetothebackofthedock.
Thegraynylonwasherwillgobetweenthis
bracketandtheDMMswivelplate.
Attachframewith1/4"x1/2”panheadbolts
andstarwashers.Passengersideshown.

C‐DMM‐3011_INST_3‐19
Determinedesiredpositionforyourspecificcomputer
andattachtoDMMswivelplateusing1/4"nylon
washers,steelwashers,andnylocknuts. Tightensothat
thedockrotatessmoothly.(Firm,butnottootight)
Checkandadjustpositioningasdesired.
Testforproperlatchinginclosedposition.
Testup/downandsidetosidemotiontoconfirm
wireshaveadequateslackandstrainrelief.
Dock the computer and test.

Pushuplatchto
releaseandlift
RoutewiringalongthesideoftheDMMflipup
frameusingwiretiesandexistingholes.
Installation is now complete.