Havis C-DMM-3011 User manual

C-DMM-3011_INST_4-20
TOOLS REQUIRED:
•Ratchet Wrench • Socket Set • 7/16” Open End Wrench • T-20 Torx bit
• Phillips Screwdriver (short) • Dash panel removal tool • Wire stripers/cutters
Notes:
1. The C-DMM-3000 swivel plate accepts C-MM-301 offset bracket used with C-MM-2XX adaptors.
2. C-MM-2XX series adaptor brackets are not needed for most VESA 75 and other Havis Docking
Station mounting applications.
3. CM010471 VESA rotator plate gives additional positioning options, but is not required
depending on mounting preference.
4. Does NOT work with 8.4”, 12” displays or other radios with the following Sales codes:
UAS, UAM, UAQ, UAV and UAX
ALWAYS!
 Read all instructions before installing any Havis, Inc products.
 Use hardware provided with install kit
INSTALLATION
INSTRUCTIONS
C-DMM-3011 Flip up Dash Monitor Mount
2013-2019 Ram 1500 Special Services Police & 1500 Tradesman Pickup Truck with "Classic" Body style
2013-2019 Ram 1500, 2500, 3500 Retail Pickup Truck with "Classic" Body style
**Compatible with 3-Inch and 5-Inch Radio Display ONLY (Sales codes RA1, UA1, RA2, UAA)**
HARDWARE and PARTS:
QTY DESCRIPTION PART#
1 Driver side mount CM009612
1 Passenger side mount CM009613
2 Side support bracket CM009614
1 VESA rotator plate CM010471
2 1/4" x 3/4" Carriage bolts GSM32000
1 PVC washer CM010648
2 1/4" Plastic flat washer CM86600
4 1/4" Steel flat washer GSM31005
4 1/4" Nylock nut GSM30016-1
4 1/4" Star washer GSM31035
4 1/4"x 1/2" Phillips pan head bolt GSM33123
4 1/4"x 1/2" Flat head bolt GSM34057
2 1/4"x 3/4" Hex head bolt GSM33001
4 8-32 Keps nut GSM30027
1 Loctite (removable medium strength) GSM20075

C-DMM-3011_INST_4-20
CM009612
Driver side
Mount
Frame and hinge
mount assembly
CM010471
VESA rotator
plate
CM010648
PVC washer
C-DMM-3011
Assembly
GSM34057
1/4"x 1/2" Flat head bolt
GSM20075
Loctite
CM009613
Passenger side
Mount
CM86600
1/4" Plastic washer
GSM31005
1/4" Steel washer
GSM30016-1
1/4" Nylock nut
CM009614
Side support bracket
(One each side)
GSM30027
8-32 Keps nut
GSM33123
1/4"x 1/2" Pan head bolt
GSM3103
1/4" Star washer
GSM33001
1/4"x 3/4" Hex bolt
GSM30016
1/4" Nylock nut
GSM31005
1/4" Flat washers
(Not shown)
GSM32000 – 1/4"x
3/4"Carraige bolt

C-DMM-3011_INST_4-20
Remove rubber liner and remove screws in
upper center coin tray. (T20 Torx bit)
Remove screw in lower right dash pocket.
(T20 Torx bit)
Dodge Ram Pickup dash with Uconnect® 3
Radio with 5-Inch Display prior to installation.
Remove rubber liner in lower right dash pocket.
Remove radio mount screws, unplug and
remove radio control. (7mm socket)
Carefully partially remove center instrument
panel. This does not need to be unplugged.

C-DMM-3011_INST_4-20
Attach driver and passenger side mount brackets
to inner OEM frame with 1/4"x 3/4" hex head
bolt
s,
flat washers
and
n
ylock nuts.
Tighten mount bracket hardware. Snap center instrument panel back into place.
Mount brackets will come out through sides of
radio opening.
Loosely attach driver and passenger side mount
brackets (CM009612 & CM009613) to radio mount
holes with OEM radio mount screws.
Reattach upper coin tray and lower dash
pocket with previously removed screws.
Attach side support bracket to driver side mount
bracket with 1/4"x 1/2" flat head bolts.
Note: Use a drop of Loctite on each bolt.

C-DMM-3011_INST_4-20
Place frame & hinge assembly onto support brackets
and make sure it fits around radio properly.
Plug radio back in and attach to support brackets
with 8-32 Keps nuts. (11/32” socket)
Position VESA plate on back of Device as desired.
Attach VESA plate with carriage bolts to the back
of the dock. The gray PVC washer will go between
this bracket and the DMM swivel plate
Attach frame with 1/4" x 1/2” pan head
bolts and star washers. Driver side shown.
Attach frame with 1/4" x 1/2” pan head bolts
and star washers. Passenger side shown.
Attach side support bracket to passenger side
mount bracket with 1/4"x 1/2" flat head bolts.
Note: Use a drop of Loctite on each bolt
.

C-DMM-3011_INST_4-20
Determine desired position for your specific computer
and attach to DMM swivel plate using 1/4"x 3/4” carriage
bolts, PVC spacer, nylon washers, steel washers, and
nylock nuts. Tighten so that the dock rotates smoothly.
Check and adjust positioning as desired.
Test for proper latching in closed position.
Test up / down and side to side motion to confirm
wires have adequate slack and strain relief.
Dock the computer and test.
Push up latch to
release and lift
Route wiring along the side of the DMM flip up
frame using wire ties and existing holes.
Installation is now complete.