hayneedle Maul Breezes User manual

Owners Manual
Warning : Read and follow these instructions carefully and be mindful of all warnings shown throughout. Warning :Read and follow these instructions carefully and be mindful of all warnings shown throughout.
UL
R
56" Maui Breezes
N.W. : 13.00 kgs.
G.W. : 15.00 kgs.
56" Maui Breezes
N.W. :13.00 kgs.
G.W. :15.00 kgs.
56" Bel Air
N.W. : 12.00 kgs.
G.W. : 14.00 kgs.
56" Bel Air
N.W. :12.00 kgs.
G.W. :14.00 kgs.

WARNING : TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,
PLEASE OBSERVE THE FOLLOWING :
WARNING :TO REDUCE THE RISK OF FIRE, ELECTRICAL SHOCK, OR INJURY TO PERSONS,
PLEASE OBSERVE THE FOLLOWING :
READ AND SAVE THESE INSTRUCTIONSREAD AND SAVE THESE INSTRUCTIONS
1. To ensure the success of the installation, be sure to read the instructions and review the diagrams
thoroughly before beginning.
2]. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.
All electrical connections must be made in accordance with local codes, ordinances and/or the
National Electric Code. If you are unfamiliar with the methods of installing electrical wiring and
products, secure the services of a qualified and licensed electrician as well as someone who can
check the strength of the supportive ceiling members and make the proper installations and
connections.
3]. Make sure that your installation site will not allow rotating fan blades to come in contact with any
object. Blades should be at least 7 feet from floor when fan is in operation.
4]. If possible, mount ceiling fan on a ceiling joist - the joist must be able to support the motion and weight
of the moving fan. If the fan will be mounted on a ceiling outlet box, a 4" x 2-1/8" deep METAL octagon
box is required ; one UL listed as " suitable for fan support ". The box and its supporting members must
not be able to twist or work loose. DO NOT USE PLASTIC BOXES. Installation on a concrete ceiling should
be performed by qualified personnel.
5]. Blades should be attached after motor housing is hung and in place. Fan motor housing should be
kept in carton until ready to be installed to protect its finish. If you are installing more than one ceiling
fan, make sure that you do not mix fan blade sets.
6]. After making electrical connections, spliced conductors should be turned upward and pushed
carefully up into outlet box. The wires should be spread apart with the grounded conductor and the
equipment - grounding conductor on one side of the outlet box and the " HOT " wires on the other side.
7]. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL listed
and should be installed per the light kit's installation instructions.
8]. After fan is completely installed, check to make sure that all connections are secure to prevent fan
from falling and/or causing damage or injury.
9]. The fan is ready for operation after installation. The bearings are adequately lubricated. No
additional lubrication is necessary.
10]. The fan must be turned off and stopped before reversing fan direction.
11]. This fan is suitable for indoor use only.
12]. This fan is suitable for use with solid-state speed control.
1. To ensure the success of the installation, be sure to read the instructions and review the diagrams
thoroughly before beginning.
2]. To avoid possible electric shock, be sure electricity is turned off at the main power box before wiring.
All electrical connections must be made in accordance with local codes, ordinances and/or the
National Electric Code. If you are unfamiliar with the methods of installing electrical wiring and
products, secure the services of aqualified and licensed electrician as well as someone who can
check the strength of the supportive ceiling members and make the proper installations and
connections.
3]. Make sure that your installation site will not allow rotating fan blades to come in contact with any
object. Blades should be at least 7feet from floor when fan is in operation.
4]. If possible, mount ceiling fan on aceiling joist -the joist must be able to support the motion and weight
of the moving fan. If the fan will be mounted on aceiling outlet box, a4" x2-1/8" deep METAL octagon
box is required ;one UL listed as "suitable for fan support ". The box and its supporting members must
not be able to twist or work loose. DO NOT USE PLASTIC BOXES. Installation on aconcrete ceiling should
be performed by qualified personnel.
5]. Blades should be attached after motor housing is hung and in place. Fan motor housing should be
kept in carton until ready to be installed to protect its finish. If you are installing more than one ceiling
fan, make sure that you do not mix fan blade sets.
6]. After making electrical connections, spliced conductors should be turned upward and pushed
carefully up into outlet box. The wires should be spread apart with the grounded conductor and the
equipment -grounding conductor on one side of the outlet box and the "HOT "wires on the other side.
7]. Electrical diagrams are for reference only. Light kits that are not packed with the fan must be UL listed
and should be installed per the light kit's installation instructions.
8]. After fan is completely installed, check to make sure that all connections are secure to prevent fan
from falling and/or causing damage or injury.
9]. The fan is ready for operation after installation. The bearings are adequately lubricated. No
additional lubrication is necessary.
10]. The fan must be turned off and stopped before reversing fan direction.
11]. This fan is suitable for indoor use only.
12]. This fan is suitable for use with solid-state speed control.

Blade x 5Blade x 5
Blade Holder x 5Blade Holder x 5
Fan AssemblyFan Assembly
Yoke CoverYoke Cover
Light Kit
Housing
Light Kit
Housing
1. Unpack and inspect fan carefully to be certain all contents
are included.
1. Unpack and inspect fan carefully to be certain all contents
are included.
Bulbs
Up-Light
E-12, 15W
x4pcs.
Up-Light
E-12, 15W
x4pcs.
Down-Light
JD-E11, 100W
x1pc.
Down-Light
JD-E11, 100W
x1pc.
Remote
Transmitter Receiver
Up Glass
Shade
Up Glass
Shade
Down Glass
Shade
Down Glass
Shade
Mounting
Bracket
Mounting
Bracket
Canopy
Downrod
Assembly
Downrod
Assembly
Suitable for use with solid-state speed controlSuitable for use with solid-state speed control

Place the up glass shade onto grill & secure the
glass shade with three glass screws / spring
clips on grill.
Gently install E-12 (4pcs.) Light bulbs on lampholder.
1.Insert downrod assembly through canopy & yoke cover as shown above.
2.Feed motor lead wires through downrod assembly.
3.Insert the downrod assembly into yoke.
4.Insert the cross pin through Yoke and downrod and secure with Cotter Pin.
5.Tighten both set screws to further secure downrod.
6.Tighten hex nuts existing on set screws toward yoke to prevent set screws from loosening.
7.Connect 9-pin connector, pull down the yoke cover & fasten jam screw on top of yoke cover.
Light Bulb x 4
Spring Clip x 3
Glass Screws x 3
5. Yoke & downrod assembly5. Yoke &downrod assembly
6. Up glass shade assembly6. Up glass shade assembly
Grill
Yoke CoverYoke Cover
Canopy
Up Glass ShadeUp Glass Shade
OFF OFF OFF
Turn off power at breaker
box to avoid possible
electrical shock.
Use metal outlet box suitable for
fan support.
Secure outlet box directly to the
building structure using wood
screws (included).
Outlet box must support 40 lbs
min.
Install mounting bracket
to Outlet box in ceiling
using washers and the
mounting screws
provided with the outlet
box.
2. 3.
4.
Do not use existing mounting
bracket, replace it with new
mounting bracket from box.
Do not use existing mounting
bracket, replace it with new
mounting bracket from box.
Outlet BoxOutlet Box
Mounting
Bracket
Mounting
Bracket
Canopy
Yoke CoverYoke Cover
Yoke
Cross PinCross Pin
Cotter PinCotter Pin
Set Screw
with Hex Nut(2)
Set Screw
with Hex Nut(2)
Wire Connectors
from Yoke Cover
Wire Connectors
from Yoke Cover
Wire Connectors
from Fan
Wire Connectors
from Fan
Downrod assemblyDownrod assembly

From Remote ControlFrom Remote ControlFrom HouseFrom House From FanFrom Fan
Orange(For Upper Light) Orange
White(AC In N)
Black(AC In L)
Blue(To Bottom Light)
Green/Ground
White
Black
Green/Ground
Make sure that all exposed wires are secured inside wire nuts.
Gently push wires into Mounting bracket with nuts pointing upward.
White(To Motor N) White
Black(To Motor L) Black
Blue
8. Make wire connection8. Make wire connection
3.Install the Mounting Bracket3.Install the Mounting Bracket
Lift fan assembly onto
mounting bracket.
Carefully lift fan assembly onto mounting bracket.
Rotate fan so that the groove on the ball engages
the ridge in the mounting bracket.
Ridge
Ball GrooveBall Groove
Mounting
Bracket
Mounting
Bracket
Mounting
Bracket
Mounting
Bracket
7. Hanging the fan7. Hanging the fan
1.Push up the Canopy until the two screws on mounting bracket
are engaged with Key Holes in canopy.
2.Rotate the canopy slightly until the two screw heads are in the
small end of the Key Holes.
3.Tighten both screws.
Canopy
Key HolesKey Holes
Screw
9. Install the canopy9. Install the canopy
This fan is suitable for use with solid-state speed control.This fan is suitable for use with solid-state speed control.

Attach blade to blade holder with screws
provided.
Make sure that all screws are firmly tightened.
Attach the blade assembly to motor using
motor screws provided.
Note : Do not bend Blade
holder to prevent wobble.
Note :Do not bend Blade
holder to prevent wobble.
10. Blade installation10. Blade installation
Blade HolderBlade Holder
Blade
Paper WasherPaper Washer
Blade ScrewBlade Screw
11. Blade assembly to motor11. Blade assembly to motor
Motor ScrewMotor Screw
Blade AssemblyBlade Assembly
Connect pins of white wire from fan to white
wire from light kit & blue wire from fan to black
wire from light kit.
White Wire
From Fan
White Wire
From Fan
White Wire
From Light Kit
White Wire
From Light Kit
Black Wire
From Light Kit
Black Wire
From Light Kit
Blue Wire
From Fan
Blue Wire
From Fan
12. Make wire connection for light kit12. Make wire connection for light kit

Screw HoleScrew Hole
Key HoleKey Hole
Key HoleKey Hole
Set ScrewSet Screw
Screw
Screw
Round plateRound plate
Glass Set ScrewGlass Set Screw
Attach & align 3 key holes on light kit pan
to 3 screws on round plate, rotate light
kit pan until 3 screw heads to small end,
then fasten 3 screws tightly, Gently
install 1 halogen bulb, included, to
lamp holder.
Ridge
Groove
Glass
Shade
Glass
Shade Attach & rotate down glass shade
clockwise to light kit pan.
Gently fasten glass set screw on side of light kit pan
to prevent loosening.
13. Install light bulbs & glass13. Install light bulbs &glass
Turn on the power, your fan is ready for operationTurn on the power, your fan is ready for operation