manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Hayward
  6. •
  7. Light Fixture
  8. •
  9. Hayward Universal ColorLogic Parts list manual

Hayward Universal ColorLogic Parts list manual

STEP 2: Detach Light
STEP 1: Find Junction Box
STEP 3: Cut Light Cord STEP 4: Tape Cord ends
Before you begin
Pre-Installation Checklist
Installation Preparation
Keep the Universal ColorLogic/
CrystaLogic light on the pool
as shown. Using
too much tape
may prevent the
cord from mov-
ing freely through
conduit.
deck Dry the cord ends
thoroughly and tape them
Replacing 120 volt pool or spa lights
with Universal ColorLogicTM or CrystaLogicTM
Turn Over
If no junction box: If there is no junction box in place, the connection to the existing light is made
directly to a switch, timer, pool controller, or subpanel. If so, a listed Pool/Spa wall mount transformer
(Hayward®LTBUY11300) or a junction box transformer kit (Hayward LTBUYxxx) can be used to power
the new Universal ColorLogic/CrystaLogic light. Consult with an electrician to re-wire and modify the
existing conduit conguration to include the new transformer.
If there is a junction box: Determine the manufacturer of your pool or spa light’s junction box and
aquire a compatible Hayward junction box transformer retrot kit. Refer to the chart below for Hayward
retrot kit part numbers.
Remove the junction box cover
and disconnect the existing light.
Remove the light from the niche.
Firmly pull on the light cord at the
Place the light on the pool deck and cut the light
cord as shown below.
Existing pool or spa light operates on 120 volts
There is a dedicated electrical junction box for the pool/spa light (see Step 1)
A suitable transformer has been aquired (refer to Step 1 for more information)
Light xture housing (Niche) has been installed per the National Electrical Code (NEC)
Your niche is compatible with the new light (refer to compatibility table in manual)
If replacing a SwimQuip®light, the tab on the Universal ColorLogicTM/CrystaLogicTM light may
need to be removed (refer to manual)
You have wire cutters or shears for cutting the existing light cord
You have duct tape for taping the new cord to the old cord when pulling through conduit
You have a Phillips head screwdriver
You are qualied to work on electrical wiring and understand electric code requirements and
wiring methods
Read the entire Universal ColorLogic/CrystaLogic manual
Read this entire Guide
Remove power to the existing pool or spa light at the service panel!
Use this Guide ONLY if your current light is a 120 volt
type. Refer
to other Guide if your light is low voltage (12v).
junction box and verify
that the cord moves
freely. There may be
a grommet or seal-
ant at the light cord’s
point of entry into the
niche. Removing this
should allow the cord to
pull freely through the
conduit. Leave cord in
place until Step 6.
STEP 6: Install and wire Junction Box Transformer STEP 9: Install Trim Ring
Install the Trim Ring as shown.
STEP 5: Snake Cord through Conduit
Pull at the junction box
or transformer end to
snake the Universal
ColorLogic/CrystaLogic
cord through the con-
duit. Leave slack at
the light end for coiling
cord in the niche. The
coil length should be
adequate for placing the
light on the deck if pool
servicing ever requires
light removal.
Some niches may have an
8AWG connection from the
junction box to the niche. If so,
ensure that this connection is
not interrupted when installing
the new light.
092501 RevA
The junction box retrot kit transformer must now
be installed and wired. Cut excess cord and refer
to the diagram for wiring instructions.
If the new Universal ColorLogic/CrystaLogic light
will be controlled by network communications
using a Hayward Pro Logic controller, an
LKBUN1000 coupler must also be installed.
Refer to the LKBUN1000 instructions for
installation and wiring information.
After wiring the Universal ColorLogic/CrystaLogic
light to the junction box transformer, install the
new cover making sure that the included gasket is
in place.
Replacing 120 volt pool or spa lights
with Universal ColorLogicTM or CrystaLogicTM
STEP 6a: Install Light to most Niches STEP 5: Insert Cell
STEP 6b: Install Light to Pentair Niche
For Pentair®niches, use the included spacer according to the
diagram below. Failure to install the plastic spacer properly may
result in the light being inadequately fastened. Plastic gunite
type niches will not require the spacer.
Refer to the manual for instructions when using a Swimquip
niche.
To fasten the Universal ColorLogic/CrystaLogic light to most
niches refer to the diagram below.
READ SAFETY INSTRUCTIONS AND COMPLETE SAFETY
CHECKLIST INSIDE FRONT COVER OF MANUAL
Hayward (R) is a registered trademark
ColorLogic (TM) and CrystaLogic (TM) is a trademark
of Hayward Pool Products, Inc.
© 2012 Hayward Pool Products, Inc.
All other trademarks not owned by Hayward are the
property of their respective owners.
Hayward is not in any way affiliated with or endorsed
by those third parties.

Other manuals for Universal ColorLogic

4

This manual suits for next models

3

Other Hayward Light Fixture manuals

Hayward ColorLogic® 4.0 User manual

Hayward

Hayward ColorLogic® 4.0 User manual

Hayward ColorLogic 160 User manual

Hayward

Hayward ColorLogic 160 User manual

Hayward Universal ColorLogic Parts list manual

Hayward

Hayward Universal ColorLogic Parts list manual

Hayward LPCUS11 Series User manual

Hayward

Hayward LPCUS11 Series User manual

Hayward ColorLogic SP-0521LED30 User manual

Hayward

Hayward ColorLogic SP-0521LED30 User manual

Hayward ColorLogic 2.5 User manual

Hayward

Hayward ColorLogic 2.5 User manual

Hayward Universal ColorLogic User manual

Hayward

Hayward Universal ColorLogic User manual

Hayward AstroLite ll Spa Lighting User manual

Hayward

Hayward AstroLite ll Spa Lighting User manual

Popular Light Fixture manuals by other brands

Spirit LEDglo installation guide

Spirit

Spirit LEDglo installation guide

Eterna vnanobh installation instructions

Eterna

Eterna vnanobh installation instructions

Tykoflex RL30 manual

Tykoflex

Tykoflex RL30 manual

SATTLER LUCE VERDE ANELLO Assembly instruction

SATTLER

SATTLER LUCE VERDE ANELLO Assembly instruction

Lightolier ProSpec 26383W specification

Lightolier

Lightolier ProSpec 26383W specification

MiLAN Wire Series Assembly instructions

MiLAN

MiLAN Wire Series Assembly instructions

American DJ Fantasy Scan 250 User instructions

American DJ

American DJ Fantasy Scan 250 User instructions

IKEA VISSVASS manual

IKEA

IKEA VISSVASS manual

Chauvet Intimidator COLOR LED user manual

Chauvet

Chauvet Intimidator COLOR LED user manual

ECI CabLite ECO Series installation manual

ECI

ECI CabLite ECO Series installation manual

TRiALED 01 series user manual

TRiALED

TRiALED 01 series user manual

RSA Lighting Combolight LV1250 Specifications

RSA Lighting

RSA Lighting Combolight LV1250 Specifications

EuroLite BLACK GUN UV-spot user manual

EuroLite

EuroLite BLACK GUN UV-spot user manual

mbt Lighting PARDL24PRO user manual

mbt Lighting

mbt Lighting PARDL24PRO user manual

Philips 6910835PU Instruction leaflet

Philips

Philips 6910835PU Instruction leaflet

ABB Stanilite installation manual

ABB

ABB Stanilite installation manual

SIGNIFY Hadco V671 Series installation instructions

SIGNIFY

SIGNIFY Hadco V671 Series installation instructions

Avlite AV-OL-ILAB-UM-R-D Installation & service manual

Avlite

Avlite AV-OL-ILAB-UM-R-D Installation & service manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.