Hayward HLRelay User manual

Hayward Pool Products
620 Division Street, Elizabeth NJ 07207
www.hayward.com
HLRelay
High Voltage Relay for OmniLogic
Owner's Manual
HLRELAY
Contents
Description............................1
Installation............................2
Conguration.........................3
092563 RevA
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

FCC Statement
This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference
received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by Hayward could void the user’s authority to
operate this equipment.
NOTE:This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio
or television reception, which can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the following measures:
-- Reorient or relocate the receiving antenna.
-- Increase the separation between the equipment and receiver.
-- Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-- Consult the dealer or an experienced radio / TV technician for help.
Industry Canada Statement
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada.
The term “IC” before the certification / registration number only signifies that the Industry Canada
technical specifications were met.
Description
The HLRELAY is a single high voltage relay accessory for the HLBASE OmniLogic pool control.
Although the HLBASE comes with four high voltage relays, up to two HLRELAYs can be added
to control additional pool and backyard equipment. After installation, the OmniLogic will detect
the HLRELAY(s) and, using the OmniLogic's CONFIGURATION WIZARD, allow you to configure the
relay(s) to control your pool equipment.
RELAY: 3HP/30A at 240V (1½HP/30A at 120V)
1
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS

Installation
DANGER of Death, Injury or Property Damage if procedure not followed. This accessory
connects to the OmniLogic panel beneath the dead front. Dead front removal is required for this
installation. Power to the OmniLogic panel MUST be shut off before the dead front is removed.
This means a complete shutdown of power to the entire OmniLogic panel.
If using a single HLRELAY, install it in the 9th relay position. For two relays, use both the 9th and
10th locations. Relay positions are shown on the diagram on page 2.
1. Shut off power to the OmniLogic System Panel and remove the deadfront.
2. Mount the relay in the proper position by sliding one of the relay mounting holes over the hook
on the System Panel. Fasten the relay with the included mounting screw through the other
mounting hole. Refer to diagram.
3. Route the connector at the end of the HLRELAY wiring harness to the appropriate connector on
the OmniLogic Main Board as shown below.
4. Replace deadfront and power up the OmniLogic.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
2
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS
2

For further information or consumer
technical support, visit our website at
www.hayward.com
Hayward is a registered trademark and OmniLogic is
a trademark of Hayward Industries, Inc. © 2013 Hayward Industries, Inc.
All other trademarks not owned by Hayward are the property of their respective owners.
Hayward is not in any way affiliated with or endorsed by those third parties.
9
10
7
8
HLRelay
HLRelay
HLRELAY relays
Configuration
The OmniLogic will automatically discover the HLRELAY(s) at power up. The relay(s) will be dis-
played in the Relay Table located in the OmniLogic's CONFIGURATION WIZARD. A single relay will
be displayed as "HVR9". If using two HLRELAYs, the table will show "HVR9" and "HVR10".
High Voltage Wiring
Refer to the OmniLogic Installation manual for detailed instructions on how to wire and assign
relays to your pool's equipment.
USE ONLY HAYWARD GENUINE REPLACEMENT PARTS