Haztec 7-1222-288-50-C User manual

Haztec International Ltd ∙ Moorfield Road ∙ Leeds ∙ LS19 7BN ∙ UK
T: [phone] ∙ inf[email protected] ∙ www.haztec.uk
7-1222-288-50-C
Combined Flood/Spot
Bar Light
M323.1.0 - 1 - April 2021
Thank you for purchasing this Haztec product. Before proceeding with installation it is essential
to read and understand this instruction booklet.
Warning!
▪This product must be installed by persons competent in vehicle electrical installations
▪Care should be taken to ensure that water ingress cannot occur through mounting or
wiring holes
▪Regularly inspect the product to confirm correct operation
▪DO NOT stare directly into the light it produces as permanent damage to the eyes may
result
▪The light becomes hot during continuous operation. DO NOT touch the casing or lens for
at least 30 minutes after switching off
▪Use only a mixture of soap and water to clean this product
▪DO NOT allow solvents, fuels or acetone-based cleaners etc. to come into contact with
this product
Basic Operating Specifications:
Supply voltage range:
12-24VDC
Power output:
23040 raw lm / 18598 eff. lm
Beam spread:
60Oflood / 30Ospot
Operating temperature range:
-40OC to +60OC
Fuse rating:
25A
Dimensions (mm):
1278 (L) x 90 (D) x 82 (H)
Connection Instructions:
Wire
Connect to
Function
Red
Permanent positive [+] via switch & fuse
Main Feed
Black
Permanent negative [-]
Earth/Ground
Note: The main feed fuse must be installed within 12” of the power source
▪3W CREE LEDs
▪288W double row
▪12/24VDC
▪IP67 rated
▪Polycarbonate Lens
▪1 year warranty

Haztec International Ltd ∙ Moorfield Road ∙ Leeds ∙ LS19 7BN ∙ UK
T: [phone] ∙ inf[email protected] ∙ www.haztec.uk
7-1222-288-50-C
Combined Flood/Spot
Bar Light
M323.1.0 - 2 - April 2021
Installation Instructions:
▪DO NOT install this product or route any wires in the deployment area any airbag system,
as this will cause damage or reduce the effectiveness of the system, or more seriously
become a projectile that could cause personal injury or death
▪Refer to the vehicle owner’s manual to identify the airbag deployment areas
▪The user/installer assumes full responsibility for determining the correct mounting
location based on providing safety to all passengers inside the vehicle
▪If mounting this product requires drilling holes, the installer must be sure that no vehicle
components or other vital parts could be damaged by the process
▪Check both sides of the mounting surface before drilling commences
▪De-burr holes and remove any metal shards or remnants
▪Install rubber grommets into all wire passage holes or seal with a suitable customer
supplied sealant
▪For this product to operate at optimum efficiency, a good electrical connection to chassis
ground must be made
▪Attach the mounting bracket to the light using the supplied ¾” bolts and tighten using an
Allen key. The brackets can be moved along the channel at the base of the light to the
required position
▪Use the supplied 1 ¼” bolts, washers and nuts to mount the lamp to the vehicle
▪Connect the red wire to positive [+] of a toggle switch and run the appropriate gauge wire
(min. 18AWG) from the input of the switch to the positive [+] terminal of the vehicle
battery
▪Connect the black ground wire to the negative [-] terminal of the vehicle battery or any
good bare metal ground source
▪When extending power wires it is recommended to solder the connections and then to
apply heatshrink over the connections
▪Activate the toggle switch to confirm correct operation of the light
Basic Dimensions: