HB 7225-ARLO 8' BT User manual

/7
#7225-ARLO 8' BT
ASSEMBLY INSTRUCTION
VERSION 06/05/2022
Step 1: Attach the Top Legs to the Legs by using Bolt (A) and Washer (B)
NO NAME SIZE PCS DRAW
A
B
BOLT
Ø3/8" x Ø3/4"
Ø3/8" x 2 3/4"
16
WASHER
16
NO NAME SIZE PCS DRAW
1
2
LEG 23 25/32" x 8 7/16"x 8 7/16"
2
WASHER
4
1
1
2
A
A
B
B
36 7/32" x 6"x 4 3/32"
1

/7
#7225-ARLO 8' BT
ASSEMBLY INSTRUCTION
VERSION 06/05/2022
NO NAME SIZE PCS DRAW
C
D
BOLT
Ø5/16" x Ø3/4"
Ø5/16" x 2"
16
WASHER
16
Step 2: Attach the Panels 2 to the Legs by using Bolt (C) and Washer (D)
DC
NO NAME SIZE PCS DRAW
3
4
END PANEL 2 26 5/8" x 5 3/16" x 2 1/2"
2
SIDE PANEL 2
2
57 5/16" x 5 3/16" x 2 1/2"
3
3
4
4
2

/7
#7225-ARLO 8' BT
ASSEMBLY INSTRUCTION
VERSION 06/05/2022
NO NAME SIZE PCS DRAW
BØ3/8" x Ø3/4"
8
24
E
G
Ø3/8"
Ø5/16" x Ø3/4"
8
8
F
BOLT Ø3/8" x 4 1/4"
8
D
NUT
8
Step 3: Attach the Side panels 1 to the Legs by using Bolt (A),(E) ,Washer (B) and Nut(F).
Step 4: Attach the End panels 1 to the Side panels 1 by using Bolt (G) and Washer (D).
G
G
D
A
E
B
B
FF
BEA
NO NAME SIZE PCS DRAW
6
5
END PANEL 1
83 15/32" x 7 1/16" x 4 11/32" 2
SIDE PANEL 1
2
36 7/32" x 4 29/32" x 4 11/32"
ABOLT Ø3/8" x 2 3/4"
WASHER
WASHER
BOLT Ø5/16" x 2 3/4"
5
5
6
6
3

/7
#7225-ARLO 8' BT
ASSEMBLY INSTRUCTION
VERSION 06/05/2022
NO NAME SIZE PCS DRAW
G
H
BOLT
Ø5/16" x 4 3/4"
Ø5/16" x 2 3/4"
4
4
D8
G
D
D
H
Step 5: Attach the beams to the panels 1 by using Bolt (G),(H) and Washer (D).
NO NAME SIZE PCS DRAW
7BEAMS 36 7/32" x 4 11/32" x 1 3/8" 2
WASHER
BOLT
Ø5/16" x Ø3/4"
7
7
4

/7
#7225-ARLO 8' BT
ASSEMBLY INSTRUCTION
VERSION 06/05/2022
NO NAME SIZE PCS DRAW
ISCREWS Ø1/4" x 2 1/2" 12
Step 6A: Locate the center piece of framed slate
and position it on the cross beam assembly so that
it is centered to both the length and width of the
assembly (you must be very accurate with
placement). Pre-drill a hole through the slate screw
hole using a 3/16” drill bit. Vacuum out debris
and secure using slate screws (I). Continue with
same process with both outside sections of slate.
Step 6B: With a level or straight edge, be sure that
the slate seams are flat and level. If adjustments
need to be made, loosen slate screws and place a
shim(s) in area that needs adjustment. Tighten
screws and check for levleness. Use Bee’s Wax or
similar to fuse the seams of the slate together.
Step 7: Remove any wax, dust and debris from the
slate surface to prep it for the bedcloth. Layout
bedcloth centering it over the slate surface.
Starting at one end, staple cloth to slate framing
working from center out toward the pockets stretch
cloth toward pockets. Go to opposite end of table
and repeat process but pull the cloth tight while
stapling. Repeat on long sides working from
center between center pocket and end pocket
stretching cloth toward the pockets as you staple.
Once cloth is completely stapled, cut pocket
openings by cutting small vertical incisions in
cloth to relax the fabric so it can be stretched and
stapled around opening. Finally, make “X” style
slits in cloth where rail bolts will go through the
slate holes (see photo).
I
I
I
I
I
I
I
I
5

/7
#7225-ARLO 8' BT
ASSEMBLY INSTRUCTION
VERSION 06/05/2022
NO NAME SIZE PCS DRAW
M
N
THREADED ROD
Ø10mm x 30mm
DOWEL
32
8
O
Ø5/16
NUT
18
24
12
4
SCREW #8 x 3/4"
Ø5/16" x 3"
METAL
P
Ø5/16 x Ø3/4"
4
J
K
D
8
8
L
Ø1/4" x Ø5/8" x 2mm
Ø1/4"x 1"
BOLT
WASHER
5 7/8" x 1 1/2" x 1 1/2"METAL
BOLT Ø1/4"x 5/8"
8-7/8"x 2-5/8" x 1/8" 2
Q
R
S
WASHER
T
SCREW
METAL
#8 x 1/2" 84
5" x 1" x 1" 14
S
T
J
K
Connect Blind
P
P
O
L
L
M
K
N
Step 10
Step 8 Step 9
Step 12
D
R
Q
D
R
Step 11
L
Step 8: Attach the Side Blinds by using Connect Blinds, Bolt (J) and Washer (K) .
Step 9: Attach the End Blinds to the Side Blinds by using Corner metals (N), Dowel (L), Bolt (M) and Washer (K) .
Step 10: Attach the Side rail by using Dowel (L), Metal (O) and Screw (P).
Step 11: Attach the Corner top to the Side rail and End rail by using Dowels(L), Threaded rod (Q), Nut (R) and Washer (D) .
Step 12: Attach all Blinds to the Rail by using Metal (T) and Screw (S).
NO NAME SIZE PCS DRAW
11
12
2
13
8
9
10
50 7/16"x 6 3/8" x 3/4"
SIDE BLIND LEFT
SIDE BLIND RIGHT
SIDE RAIL LEFT
SIDE RAIL RIGHT
END BLIND
END RAIL
50 7/16"x 6 3/8" x 3/4"
55 11/32"x 6 3/8" x 3/4"
46"x 6 1/2" x 1 1/2"
46"x 6 1/2" x 1 1/2"
58 1/4"x 6 1/2" x 1 1/2"
2
2
2
2
2
14
CONNECT BLIND 6 1/4"x 5 5/32" x 1/2" 2
8
8
9
9
10
10
11
12
12
13
13
14
14
9
10
14
13
6

/7
#7225-ARLO 8' BT
ASSEMBLY INSTRUCTION
VERSION 06/05/2022
NO NAME SIZE PCS DRAW
W
X
Ø3/8" 18
Y
Z
DOME WASHER
STAR WASHER
BOLT Ø3/8" x 3"
18
18
CORNER POCKET
CENTER POCKET
NAIL #5 x 5/8"
2
4
12
Ø3/8"
V
U
FNUT Ø3/8" 18
Step 10: Attach rail/blind
assemblies to the slate using
Dome Washer (U), Star
Washer (V), Threaded rod
(W) and Nut (F).
Step 11: NOTE: the side
pockets and corner pockets
ARE different and will only
work correctly one way. To
install the pockets, squeeze
the top of the pocket and
bring it up through the
pocket opening from the
bottom. Be sure not to push
back the pockets so they
are flush against the rail; the
first priority is to ensure they
line up with the felt near the
playing surface. Peel back
the paper to reveal the
sticky side of the velcro on
the backside of the Pocket
to secure the Pocket to the
Rail.
U
V
W
U
V
W
X
Y
Z
Z
F
F
7