Healthe Air 2.0 User manual
life in a different light
Healthe Air 2.0
User Guide
Healthe Inc. |3905 W Eau Gallie blvd, Suite 101, Melbourne, FL 32941 |877.999.5742 |healtheinc.com
2
IMPORTANT SAFEGUARDS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
When using electrical equipment, basic safety precautions should always be followed including the following:
WARNING: Risk of Electric Shock. Disconnect power at the fuse or circuit breaker before installing
or servicing.
WARNING: Risk of re or electric shock. This product installation requires knowledge of luminaires electrical
systems. Installation should be performed only by a qualied electrician in accordance with the National
Electrical Code and local building codes.
WARNING: Risk of re or electric shock. The input voltage rating of this product is 120–277VAC. AC
line voltage must meet the product input voltage rating before installation.
WARNING: Risk of re or electric shock. ONLY install this product in ceilings that have the construction
features and dimensions shown in the product documents and/or drawings.
WARNING: Risk of re or electric shock. Do not make or alter any open holes in an enclosure of wiring
or electrical components. Only those open holes indicated in the photographs and/or drawings may be
used during installation.
WARNING: Risk of electric shock.To prevent wiring damage or abrasion, do not expose wiring to edges
of sheet metal or other sharp objects.
WARNING: Risk of Electric Shock. Do not use or proceed with installation when enclosure is broken.
CAUTION: Do not use abrasive materials, glass cleaners or other solvents on cover plate or lens. Use
of these substances may cause the damage to the product. For cleaning purpose, use a mild soap solution.
SAVE THESE INSTRUCTIONS
FDA DISCLAIMER – FOOD AND DRUG ADMINISTRATION STATEMENT: The statements made within this manual
have not been evaluated by the U.S. Food and Drug Administration.These statements and the products of this company are not
intended to diagnose, treat, cure or prevent any disease.
NOT FOR SALE OR DISTRIBUTION IN HAWAII, INDIANA, NEW MEXICO, WYOMING, OKLAHOMA,
COLORADO, WASHINGTON DC, AND US TERRITORY OF PUERTO RICO.
WARRANTY
Limited Warranty Period:This lamp has a 5-year Limited Warranty. If this Product fails to operate during the Warranty Period
due to a defect in materials or workmanship, please follow the instructions below to view complete warranty details or to
submit a warranty claim.
Visit www.healtheinc.com/pages/warranties for complete warranty information, or call Customer Support at 1-877-999-5742
to submit warranty claims or request consumer complaint resolution.
Safety Information
Healthe Inc. |3905 W Eau Gallie blvd, Suite 101, Melbourne, FL 32941 |877.999.5742 |healtheinc.com
3
2X2 AND 2X4 INSTALLATION
Before starting, make sure POWER is turned off at the source to the
location that you are installing the Healthe Air 2.0. Remove existing
troffer if applicable.
NOTE: The Healthe Air 2.0 is designed to lay into a grid ceiling.
Installation Guide
2. Gently place Air 2.0 in the T-Grid ceiling making sure each tab is
secured onto the T-bar grid.
1. Place Healthe Air 2.0 in an open work space and pull out the (4)
T-Grid mounting tabs to 90° as shown
3. Bend each T-Grid mounting tab against T-bar grid and fasten with #8
sheet metal screw (screw not included) to secure Troffer to T-bar grid
in accordance to National Electrical Code and local building codes.
4. Attach hanger wires from the building ceiling structure to the Air 2.0
in accordance to local building and safety code requirements.
6. Make all the electrical connections from power supply cable to the
Air 2.0 with wirenuts, connecting black to black, white to white, and
green to green. (See Wiring Diagram on page 4.)
7. After all electrical connections are made, attach the power conduit
plate back onto the Air 2.0 to complete installation.
5. Remove power conduit plate, feed power supply cable into the
conduit plate, and install with appropriate electrical tting.
Healthe Inc. |3905 W Eau Gallie blvd, Suite 101, Melbourne, FL 32941 |877.999.5742 |healtheinc.com
4
WIRING DIAGRAM
0–10V Dimmer
Healthe Air 2.0
2x2
(+) Violet(-) Grey
0–10V Signals
Ground (Green)
AC Input —Line (Black)
AC Input—Neutral (White)
Installation Guide
Service Guide
Routine maintenance to key components of the Healthe Air 2.0 will help to
sustain peak performance and minimize downtime. For optimal performance of
the HEPA/Charcoal lter, it should be inspected monthly and is recommended
to be replaced every six to twelve months depending on environment. For
UVC LED, it is recommended to replace after every 3,000 hours of operations.
Please refer to the UV LED Module Replacement Schedule below.
REPLACING HEPA/CHARCOAL FILTER IN AIR 2.0
1. Shut of the main power to the Healthe Air 2.0 via the main wall switch.
2. The HEPA lter is located behind the perforated screen door opposite of the
motion sensor. Remove the two screws (5/64 hex) securing the screen door
and allow the door to swing down. (Fig 1)
3. Once the screen door is opened, bend the tabs on the side of the lter to
release and remove it. (Fig 2)
4. Install new lter.
5. Close the screen door and secure with the corresponding screws and turn on
the power. (Fig 1)
UVC LED MODULE REPLACEMENT SCHEDULE
This recommended replacement schedule is based on a daily average
hours of operation.
Hours of Daily Operation Replace the Modules Every
2 hours/day 48 months
4 hours/day 24 months
8 hours/day 12 months
12 hours/day 8 months
REPLACING UVC LED MODULE IN AIR 2.0
1. Shut of the main power to the Healthe Air 2.0 via the main wall switch.
2. Remove the two (5/64 hex) screws from each of the perforated screen
doors (2 screws each door, 4 total) and allow the doors to swing down. (Fig
3)
3. Once both doors are opened, remove the four screws securing the general
illumination LED module and allow it to swing down to expose the two (2)
UVC LED Modules behind it. (Fig 4 and Fig 5)
4. Uninstall both UVC LED Modules by disconnecting the quick connects and
removing the six screws securing each of the UVC LED Module. (Fig 5)
5. Install the new UVC LED modules with the corresponding screws and attach
the quick connects to establish electrical connection. (Fig 5)
6. Reinstall the general illumination LED module back into the main housing using
corresponding screws. (Fig 4)
7. Close and reinstall both screen doors with the corresponding hex screws and
turn on the power. (Fig 3)
Fig 1
Fig 2
Fig 3
Fig 4
Fig 5
©2020 Healthe Inc. All Rights Reserved.
Specications subject to change without notice.
DOC-00009-REV1
Healthe Inc.
3905 W Eau Gallie Blvd, Suite 101, Melbourne, FL 32934
877.999.5742 |healtheinc.com
Table of contents
