Heatilator Icon I100 User instructions

60-5/8" [1540]
20-3/4"
[527]
11-5/8"
[295]
29-1/2"
[749]
14-3/4"
[375]
Gas
Knockout
9-7/8"
[251]
19"
[483]
10-1/2"
[267]
Outside
Air
14-3/4"
[375]
Gas
Knockout
9-7/8"
[251]
19"
[483]
10-1/2"
[267]
Outside
Air
50" [1270]
33"
[838]
68-1/8"
[1730]
effective height
8-3/4
[222]
70-1/2"
[1791]
60-1/4"
[1530]
54-3/8"
[1381]
41-5/8" [1057]
Top View
Front View
Left Side View Right Side View
* Framing must be filled in to top of front
standoff after unit is installed.
Specifications
Additional information can be found online at www.heatilator.com or www.fireplaces.com
I100
Please consult the manufacturer’s
installation manual for all details and
requirements before making a final
design layout decision.
Icon I100
50" Wood Fireplace
MODEL FRONT WIDTH BACK WIDTH HEIGHT DEPTH FIREPLACE OPENING
I100 Actual Framing Actual Framing Actual
Rough
Opening
Framing*
Actual Framing 50 x 33
60-5/8 61-5/8 41-5/8 61-5/8 70-1/2 71 29-1/2 30-1/2

CLEARANCES TO COMBUSTIBLES
FRAMING DIMENSIONS
MANTEL LEG/WALL PROJECTIONS
HEARTH EXTENSION CONSTRUCTION
APPLIANCE LOCATION
MANTEL PROJECTIONS
HEARTH EXTENSIONS
30-1/2"
[775]
77-5/8" [1972]
1/2" [13] all
configurations
In an exterior chase
or projecting into
a garage
Across a
corner
Along a wall
30-1/2"
[775]
24"
[610]
77-5/8" [1972]
As a
room
divider
30-1/2"
[775]
48"
[1219]
77-5/8"
[1972]
52-1/2"
[1334]
61-5/8"
[1565]
104-7/8"
[2664]
24-3/8"
[619]
74-1/4"
[1886]
24"
[610]
Use only non-combustible
material below the top of
the front standoffs.
**30-1/2"
[722]
*8"
[203]
61-5/8"
[1565]
* Extra space needed (both sides)
for outside air connection. If outside
air duct has no bend, this dimension
may be reduced as long as minimum
clearances are met.
** If interior of chase will be
drywalled, add the thickness
to this measurement
Header will sit
on top of front
standoffs after
fireplace is
installed.
2" [51]
17"
[432]
60-5/8" [1540]
50" [1270]
24"
[610]
24"
[610]
19-3/4"
[502]
22-3/8"
[568]
FLUSH
FRONT
4"
[102]
BRICK
FRONT
50° angle
39° angle
Grid represents
1" scale
2" [51]
required
Continuous, non-combustible
sealant
Tile, stone or other
non-combustible material
Floor constructed of wood or
other combustible material
1/2" [13] Micore or
equivalent insulation
See Install Manual
Fireplace
Protective
Metal Hearth
Strip
74"
[1880]
50"
[1270]
12"
[305]
12"
[305]
Raised Hearth
20" [508]
minimum
Flush Hearth
30" [762]
minimum
0" from
floor
Attic
Insulation
Shield
Ceiling Firestop
(ceiling)
(roof)
(attic)
(ceiling)
2" [51]
minimum
2" [51]
minimum
2" [51]
minimum
2" [51]
minimum
2" [51]
minimum 2" [51] minimum
to header
2" [51]
minimum
Ceiling Firestop Offset/Return with
hanger straps
Storm Collar
Roof Flashing
0" to level
of standoffs
1-1/2" [38] from
back of unit
1-1/2" [38] from side of unit
(except at nailing flanges
where it is 1/2" [13]
7 ft [2134] minimum
base of fireplace
to ceiling
Combustible Wall
2 x 4 stud wall
Front Standoffs
Measured from top of fireplace opening
12" [305]
12" [305]
minimum
Mantel
1-1/ 2" [38]
maximum
6" [152]
minimum
20" [508]
minimum
Combustible
Decorative Facing
Non-combustible
Decorative Facing
such as: steel, iron
brick, tile, concrete,
slate, plasters
Seal joint with
non-combustible
sealant
Grid represents 1" squares
1/2"
[13]
Fireplace must be set out
1/2 [13] in front of the face
of the framing material.
Specifications
WS/HTL/I100_0615
Additional information can be found online at www.heatilator.com
PRODUCT LISTING CODES
US UL 127
Product information provided is not
complete and is subject to change without
notice. Product installation must adhere
strictly to instructions accompanying
product to avoid risk of fire and potential
injury.
Lakeville, MN Phone: [phone]
Web: www.heatilator.com
I100