Heatmaster Seamless User manual

Quick Step Installation Manual
www.heatmaster.com.au
seamless

600
Framing
opening
455 Lining
opening
required
Seamless Heater
200min
1300 530
Non-combustible
wall lining to be
used to cover
the face of
chimney breast.
Avoid joins in wall
lining directly
above firebox
Unit to sit on
non-combustible base
Quick Step Installation Manual
seamless
2
Back view in mm
680
540
505
Front view with 40mm fascia attached
440
200
10mm standoff bracket at back 12mm standoff bracket on sides
495
Top view in mm (Firebox only)
1250
1320
Firebox dimensions
Clearances from combustibles
• Sides =12mm
• Back =10mm
• Top =150mm (to noggin)
• Firebox to sit ush with front wall. Do not recess.
*Unit to sit on non - combustible base
Minimum framing dimensions and clearances
If installing into an enclosure
such as joinery, air ventilation is
required.
• Minimum enclosure height
from top of box = 300
• 1 Inlet and 1 outlet ventilation
with a cross sectional area of
5000mm for each.

Quick Step Installation Manual
seamless
3
Gas input
High 36 MJ/h
Low 18 MJ/h
Attaching outer glass
Hooks go over the panel pin on
the side of the unit
In-line for assembly
2
1
3
4
1 – Electrical power cable (Requires
isolation switch)
2 – Incoming gas connection (1/2”
BSP Male connector)
3 – Incoming air
4 – Extraction fan
A – Flue though wall, oor or ceiling
B – Inner glass gets screwed to rebox
C – Outer glass gets hooked on to rebox (Refer to
diagram above)
D – Fascia attaches to the front of the
rebox to nish ush with the wall
E – non-combustible wall lining
to be used to cover
chimney breast
Isolation
switch
A
B
C
D

seamless
Quick Step Installation Manual
seamless
4
Openable
Window
Door
T
a
l
a
b
Flue Terminal Indicates areas for flue terminals
c
c
c
c
d
m
g
d
PM
f
h
h
h
j
jj
Use 3 bends only
Our flexible flue has the ability to bend
3 times between the heating unit and
the cowl. This includes the bend
straight out of the heater if you’re
fluing through the ceiling or floor.
Make the flue pipe go over
the bearers and joists.
You may bend the flue over joists and bearers.
It is recommended that a 20mm clearance be
maintained between the smaller gas exhaust
flue and combustible materials.
Fluing where the pipe had a spot
lower than the rest.
Never allow a low spot in the flue.
Installing the flue with a dip or “goose
neck” can result in reduced efficiency or
even prevent the fire from working.
2
1
3
4
2
1
3
4
2
1
3
4
Do...
Do...
Never Do...
Using your exible ue pipe
The Seamless’s revolutionary ue system incorporates one
65mm diameter pipe and one 58mm diameter pipe.
Congure triangle
Addition literature
Supplements for ue installation can be obtained by contacting your Heatmaster dealer.
Key Information – Quick step check list
*All information contained in this mini summary is correct at the time of publication. This is only a summary and should be read in conjunction with the full installation
instructions. Pictures are representative only and are not drawn to scale. Installation should be carried out by a licensed gas tter and any electrical work carried out by a
licensed electrician.
Minimum clearances required for balanced ue terminals or the ue terminals of outdoor appliances
(To be installed in accordance with local authority requirements)
a Bellow eaves, balconies or other projections 300 mm
b From the ground or above a balcony 300 mm
c From a return wall or external corner 500 mm
d From a gas meter (M) 1000 mm
e From an electricaity meter or fuse box (P) 500 mm
f From a drain or soil pipe 150 mm
g Horizontal from an building structure 500 mm
h
From any other ue terminal, cowl or combustion air intake 500 mm
j Horizontally from an openable window, door, or non-mechanical
air inlet, or any other opening into a building, with the exception of
sub-oor ventilations 500 mm
k Vertically below an openable widow, door,or non-mechanical
air inlet, or any other opening into a building, with the exception of
sub-oor ventilation 150 mm
l Minimum horizontal clearance to any surface
(such as an exterior wall) for vertical terminations 610 mm
m Minimum height above roof line for vertical termination 600 mm
✘
✔
✔
0m 1m 2m 3m 4m
4m
3m
2m
1m
Example 1
Example 2
Example 3
1
2
3
A 20mm clearance is recommended from the extraction (smaller) ue to combustibles.
NOTE: NOT INTENDED FOR FIREPLACE INSERT
Plumber Incoming gas connection provided – 1/2 inch BSP male connector *please provide approved 1m ex gas
pipe & gas shutoff valve, to allow for removal if required.
Gas input – 36MJ high
18MJ low
Manifold pressure
(Nat gas) 0.88 Kpa
Appliance must be tested for correct operation prior to leaving
If appliance cannot be adjusted to perform correctly contact Heatmaster
Electrician Standard ex 2m, 3 pin plug provided. Requires power point with double pole isolation switch.
Using up to three bends, use this triangle to work
out measurements for your 4.5 mtr ue. The
Seamless can be ued through the roof,
wall or oor. *See your Heatmaster
dealer for full details.