HeatStar HSP40E Assembly instructions

WARNING: If the information in this manual is not followed exactly, a fire or
explosion may result causing property damage, personal injury or loss of life.
— Thisheaterhashotorarcingpartsinside.Donotuseitinareaswheregasoline,paintorother
flammableliquidsareusedorstored.
— Servicemustbeperformedbyaqualifiedserviceagency.
Languages included
• English
For Indoor Use Only
Not For Use Outdoors
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
OPERATING INSTRUCTIONS
AND OWNER’S MANUAL
READ INSTRUCTIONS CAREFULLY:Readandfollowallinstructions.Placeinstructionsinasafe
placeforfuturereference.Donotallowanyonewhohasnotreadtheseinstructionstoassemble,
light,adjustoroperatetheheater.
Model#
HSP40E
Electric Construction
HEATER
HEATSTARbyENERCO,4560W.160THST.,CLEVELAND,OHIO44135•866-447-2194

2
HEATSTAR Electric Construction Heater Operating Instructions and Owner’s Manual
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
WARNING: UNITNOTINTENDEDFORUSININDOORAREAS
WHEREHEATERMAYBEEXPOSEDTOWATER.AVOIDUSEIN
BATHROOMS,LAUNDRYROOMSORANYOTHERAREASWHERE
THEUNITMAYCOMEINCONTACTWITHWATER.NEVERLOCATE
THEHEATERWHEREITMAYFALLINTOABATHTUBOROTHER
LIQUIDCONTAINER.
WARNING:Donotoperateanyheaterwithadamagedcord
orplugoraftertheheatermalfunctions,hasbeendroppedor
damagedinanymanner.Returnheatertoauthorizedservice
facilityforexamination,electricalormechanicaladjustmentor
repair.
WARNING:Donotpointatflammablematerials.
WARNING:Donotinsertorallowanyforeignobjectsto
entertheunitviatheintakeorexhaustventsontheunit.
Failuretoobservethiswarningmayresultinelectricshock,fire
ordamagetotheunit.
WARNING:Topreventfiredonotblockeithertheairintake
orexhaustinanymanner.Donotuseonsoftsurfaceslikea
bed,whereopeningsmaygetblocked.
WARNING:Unitisequippedwithinternalactiveelectrical
componentsthatsparkduringuse.Donotuseinareaswhere
fumesfromgasoline,paintorotherflammableliquidsmaybe
present.
WARNING:Extremecautionmustbeusedwhenanyheater
isusedbyornearchildrenorinvalidsandwhenevertheheater
isleftoperatingandunattended.
WARNING: Donotuseoutdoors.
WARNING: Usethisheateronlyasdescribedinthismanual.
Anyotherusenotrecommendedbythemanufacturermay
causefire,electricshock,orinjurytopersons.
SAVE THESE INSTRUCTIONS.
WARNING: DO NOT OPERATE THIS
HEATER UNTIL YOU READ AND UNDER-
STAND THIS INSTRUCTION MANUAL FOR
SAFETY, OPERATION, AND MAINTENANCE
INSTRUCTIONS.
CAUTION:Useofthisheaterinanymeansnotdescribedin
thismanualmaycausefire,electricshock,personalinjuryand/
orpropertydamage.
CAUTION:Thisheaterishotwheninuse.Toavoidburns,
donotletbareskintouchhotsurfaces.Usehandlewhen
movingthisheater.Keepcombustiblematerials,suchas
furniture,pillows,bedding,papers,clothes,andcurtainsat
least6feet(2m)fromthefrontoftheheaterandkeepthem
awayfromsidesandrear.
CAUTION:Inordertoavoidunintendedcyclingoftheheater,
alwaysunplugorunitfrompowersourcewhennotinuse.
CAUTION: TODISCONNECTHEATER,reduceambient
thermostattozero.Fanwillcontinuetorununtilunitcoolsand
shutsdownautomatically,turnswitchesoff,disconnectpower.
CAUTION:Donotcoverthepowersupplywiringor
runthewiringunderanycarpetorrugs.Arrangecordand
connectionsawayfromtrafficpatternssoitisnotatripping
hazard.
CAUTION:Connectunittoonlyproperlygroundedoutlets
andadequatelysizedandgroundedelectricalsystems.Always
plugheatersdirectlyintoawalloutlet/receptacle.Neveruse
withanextensioncordorrelocatablepowertap(outlet/power
strip)
CAUTION:Donotusethisunitwithunapprovedorunder
sizedelectricalconnectionsorwiring.Theymayoverheatand
causeariskoffire.
Definitions: Safety Guidelines IMPORTANT INSTRUCTIONS.
Thedefinitionsbelowdescribethelevelofseverityforeachsignalword.Pleasereadthemanualandpayattentiontothesesymbols.
Danger:Indicatesanimminentlyhazardoussituationwhich,ifnotavoided,willresultindeath or serious injury.
Warning:Indicatesapotentiallyhazardoussituationwhich,ifnotavoided,couldresultindeath or serious injury.
Caution: Indicatesapotentiallyhazardoussituationwhich,ifnotavoided,may resultinminor or moderate injury.
NOTICE: Indicatesapracticenotrelatedtopersonalinjurywhich,ifnotavoided,mayresultinproperty damage.
CONTENTS
WARNINGS................................................................................. 2
HEATERSPECIFICATIONS............................................................. 3
PRINCIPALOFOPERATION.......................................................... 3
SETUPANDOPERATIONINSTRUCTIONS.................................... 4
MAINTENANCEANDSTORAGE.................................................. 4
HEATERSIZINGANDCORDSELECTION....................................... 4
TROUBLESHOOTING.................................................................... 5
WIRINGDIAGRAMS................................................................. 6-7
PARTSLIST..............................................................................8-10
WARRANTY...............................................................................12
INSTRUCTIONSFORORDERINGPARTS.......................................12

Operating Instructions and Owner’s Manual
3
HEATSTAR Electric Construction Heater
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
SPECIFICATIONS
HeatOutput(MaxBTU’s) 136,000
(FirstStage) 51,200
(SecondStage) 102,400
(ThirdStage) 136,500
Watts(Max) 40,000
(FirstStage) 16,000
(SecondStage) 32,000
(ThirdStage) 40,000
ElectricalRating 480V60Hz3Ø
Min.VoltageatHeater 440
AmpDraw(Max) 50
(FirstStage) 20
(SecondStage) 40
(ThirdStage) 50
AirFlow 1,800CFM
(3,000Cu.m/hr)
PRINCIPAL OF OPERATION
AmbientThermostat 32to100˚F
Weight 130lbs.
Ducting(Max) 14”x50’(straight)
DuctPN-WD1425
14”x25’Long
TempRise(from0˚Fambient) 100˚F
dBNoise 82dB(A)1m
ULListed Ye s
Dimensions 46”Lx20”Wx25”H
Clearance to Combustibles
Outlet 6’(1.8M)
Sides 1’(.3M)
Rear 2’(.6M)
Top 2’(.6M)
Floor Combustible
Ambient Thermostat
Sensor Tube
Solid Plastic
Wheels
Overheat Sensors
Rugged Galvanized
Steel Housing
Power Selector
Contactors
Thermostat +
Switches
Fully Sealed, Non-Glowing
Stainless Steel Heating Element
(15 pcs)
Electric Fan
Motor
Steel
Handle
Aluminum
Fan Blades
WARM
AIR
OUT
COOL
AIR
IN

4
HEATSTAR Electric Construction Heater Operating Instructions and Owner’s Manual
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
Assembly
• Removetheheaterandallofthepackagingmaterialfromthe
box.
• Checkallofthepackingmaterialforloosepartsandset
aside.
• Thoroughlyinspecttheheaterfordamage.Ifanyisfound
donotcontacttheplaceofpurchase.Pleasecallthe
Manufacturerat866-447-2194.
Starting Instructions
IMPORTANT:Reviewandunderstandallwarningsinthismanual.They
areessentialforsafeuseoftheheater.Followalllocalcodes.
1. Placetheheateronastableandlevelsurface.Makesurethatno
explosiveorcombustiblefumesordustarepresent.Seethatthe
heaterisnotexposedtowaterspray,rain,ordrippingwater.Insure
clearancetocombustiblesareobserved(Seeclearancesinthe
specificationtable).
2. Connectheatertoa480V,60Hzthreephase,50Amppower
source.
IMPORTANT:ALLPOWERSOURCESNEEDTOBEEQUIPPEDWITHA
CIRCUITBREAKER!
NOTE:Whenpowerisfirstappliedtounit,theheaterfanmayblowair
outofheaterINLET.Ifthisconditionoccurs,(afterfirstremovingpower
fromcord)reversethefirsttwohotwiresatheaterterminalinletblock.(3
PhaseModelsOnly)
3. Settheremotethermostattoatemperatureabovetheambient
roomtemperaturebyturningtheknob.
NOTE:Theheaterwillstartonlyifthethermostat“callsforheat”,
meaningthatitissettohigherthanprevailingambienttemperature.
4. Settheselectorswitchtothedesiredheatingsetting.Theswitches
arelabeledS1withaheatoutputof16Kw(54,600Btu’s),S1and
S2withaheatoutputof32Kw(109,200Btu’s)orS1,S2andS3with
aheatoutputof40Kw(136,000Btu’s).
Theheaterwillnowoperateautomatically,controlledbythethermostat.
To Stop Heating
1. Turnallswitchesto“Off”.
2. Allowfantorununtilunitstopsautomatically,controlledby
unitcooldownthermostat(fanswitch).Heatermaycycle
morethanonce.
3. Unplugthepowersupplycableafterthefanhasstopped
coolingdowntheheatercompletely.
NOTE:Thisheaterisequippedwithanoverheatlimitswitchwhich
maycausetheheatertostop.Checkandremovethecauseofthe
overheatingbeforerestarting.
IMPORTANT:Neverdisconnectsupplyplugtostoptheheater
whileinoperation!!
Maintenance
WARNING:
Neverattempttoservicetheheaterwhiletheunitishot,In
use,orpluggedin.Severebodilyinjuryorelectricshockmay
occur.Onlyqualifiedservicetechniciansshouldservicethese
units.
1. Keepheaterclean(ex.drywalldust).Usepressurizedairto
blowfanbladesclean.
NOTE:Usemoderatepressuretoavoiddamagetofan
blades.
2. Inspectheaterbeforeandaftereachuse.
3. Thebearingsofthefanmotorarepermanentlylubricated
andsealed.Noadditionallubricationisneeded.
Storage
Whennotinuse,theheatermustbedisconnectedfrompower
source,dustedoffandthecordshouldbelooselywoundaround
thehandle.
For service :
PleasecallToll-Free866-447-2194orvisitwww.
heatstarbyenerco.com.
Ourofficehoursare8:00AM–5:00PM,EST,Mondaythrough
Friday.Pleaseincludethemodelnumber,dateofpurchase,and
descriptionofprobleminallcommunication.
General Electric Heater Sizing Issues
WhenrunningHEATSTARelectricheatersfromagenerator,itis
extremelyimportanttomakesurethatthegeneratorselected
foryourheaterisnotundersized.Thesinglelargestserviceissue
withHEATSTARelectricheatersisimpropersetuprelatingto
inadequatevoltageduetotoosmallofanelectricsourceand/or
toosmallofapowercord.
The HSP40E heater would require a minimum 40,000 Watt
(40KW), 480 volt three phase generator that can provide 50
amps of continuous power.
NOTE:Thisheater’sHeatingCoilOhmReadingis85.
Electrical Cord Selection for
HEATSTAR Electric Heaters
Onceyouhaveestablishedthatyouhaveenoughpowerto
properlyrunaHEATSTARElectricHeater,youstillneedtodeliver
thepowertotheheateradequately.YouwillneedtodoaVoltage
DropFormula.TheVoltageDropFormulaisamps(source),times
resistance(cord’swiresize)equalsvoltagedrop.Acordswiresize
resistancechartisbelow:
Wire Size Resistance Chart
#4 0.000308ResistanceperFoot
#6 0.000403ResistanceperFoot
#8 0.000641ResistanceperFoot
#10 0.00102ResistanceperFoot
# 12 0.00162ResistanceperFoot
# 14 0.00258ResistanceperFoot
#16 0.00409ResistanceperFoot
#18 0.00651ResistanceperFoot
Asampleformulaislistedbelow:
MinimumVoltageRequired=440V
150ft.x18gaugewire(0.00651)=.98
50ampsx.98=49.0voltdrop
480v(atsource)–49v=431volts
Conclusion:Heaterwillnotrun,wiretoosmallorcordtoolong.
OptionstoCorrecttheSituation:
1.Increasegaugeofwire:Ifyouincreasedyourwiretoa12gauge
wire,thenyourformulawouldbeasfollows:
MinimumVoltageRequired=440V
150ft.x12gaugewire(0.00162)=0.24
50ampsx0.24=12voltdrop
480volts(atsource)–12volts=468volts
Now,yourheaterwillrunproperly.

Operating Instructions and Owner’s Manual
5
HEATSTAR Electric Construction Heater
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
Troubleshooting
Symptom Cause Check Remedy
Turnthermostatupandmotordoes
notcomeon
•Nopoweronanyphase
•OverheatLimit(TO)
•MainSwitchassembly
•Motor
•MotorRelay
•ControlTransformer
•Checkfor240VbetweenL1andL2(for
singlephasemodels).Checkforpower
betweenL1andL2,L2andL3,and
betweenL1andL3(for3phasemodels).
OverheatLimit(TO)
•Checkforcontinuity.Theswitchshould
beclosed.
•Checkforcontinuity
•Checkforpropervoltagetomotor
•Checkfor24voltstocontactor
•Checkfor24voltsoutfromControl
Transformer
•RefertoSetupand
Operationsection
•Replace
•Replace
•Replace
•Makesurecontactor
pullsin.Ifnot,replace.
•Replace
MotorStartsbutaircomesoutthe
inlet
•Reversedpower(hot)wires •Checkpoweratterminalblock •Switchfirsttwopower
wiresatterminalblock
Motorstartsbutnoheat •AmbientThermostat
•Overheatlimit(s)
•Contactors
•HeatingElements
•Turnthermostataboveambient
temperature
•Checkforcontinuity.Itisaclosedswitch
•Makesuretheyareclean,tight,and
thattheypullinwhenvoltageisapplied
•Visualcheckforburns.Checkresistance
ofeachindividualelement
•Replace
•Replace
•Replace
•85KOhms
Heateroperates,fandoesn’tcool
theunitafterthermostatissatisfied
•FanCooldownThermostat •Checkforresistance
•Checkforproperwiring
•Replace
•Rewire
Highlimittripping •LowVolumeofAir •Ductrestrictions
•Dustbuilduponinletgrill
•Straightenduct
•Cleanfanarea
BeforebeginningtheTroubleshootingsection,pleasereviewtheSet-upandInstallationsectionofthismanual.Mosttechnicalissuescanbe
resolvedwithproperset-upandpreventativemaintenance.
2.Runashortercord.Ifbychanceyoucouldusea50ftcord
insteadofa150ftcord,thenyourformulawouldbeasfollows:
MinimumVoltageRequired=440V
50ft.x18gaugewire(0.00651)=.33
50ampsx.33=16.5voltdrop
480volts(atsource)–16.5volts=463.5volts
Now,yourheaterwillrunproperly.

6
HEATSTAR Electric Construction Heater Operating Instructions and Owner’s Manual
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
WIRING DIAGRAM HSP40E
480 Volt 60 Hz 3 PH
3
9
8
7
6
5
4
2
1
16
16
16
16
16
15
14 1312
11
10
# P/N DESCRIPTION
14115 8 Transformer
24115 6 Fuse
34116 5 FanMotor
44113 5 OverheatLimitSwitch
541170 AmbientThermostat
64113 7 OverheatLimitSwitch-AirOutlet
74113 6 UnitCooldownThermostat
84115 4 ToggleSwitch(foroutput16KW)
# P/N DESCRIPTION
94115 4 ToggleSwitch(foroutput+16KW)
10 4115 4 ToggleSwitch(foroutput8KW)
11 4115 2 Contactor&Coil(foroutput16KW)
12 41151 Contactor&Coil(foroutput+16KW)
13 41151 Contactor&Coil(foroutput+16KW)
14 41151 FanContactor
15 4115 2 Pole4ofContactorC1
16 4114 2 HeatingElements,2.7KWeach
WARNING: USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR
DEATH. REPLACEMENT PARTS ARE ONLY AVAILABLE DIRECT FROM THE FACTORY AND MUST BE INSTALLED BY A QUALIFIED
SERVICE AGENCY.

Operating Instructions and Owner’s Manual
7
HEATSTAR Electric Construction Heater
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
WIRING DIAGRAM HSP40E
WARNING: USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR
DEATH. REPLACEMENT PARTS ARE ONLY AVAILABLE DIRECT FROM THE FACTORY AND MUST BE INSTALLED BY A QUALIFIED
SERVICE AGENCY.

8
HEATSTAR Electric Construction Heater Operating Instructions and Owner’s Manual
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
HSP40E
A
A
11
17
18
10
9
1
1
20 12 13
14 21
1
1
7
19 8
15
164
5
6
29
24
41
40
41
36
36A
31
46
48
43
34
38
26
48
32
15
33
37
39
30
25
30
47
28
45
42
32
35

Operating Instructions and Owner’s Manual
9
HEATSTAR Electric Construction Heater
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
HSP40E
# P/N DESCRIPTION
14112 5 HeatExchangerChamber
44112 6 Hood(includingConnectionHatch)
54112 7 ConnectionHatchOnly
64112 8 Handle
74112 9 FrontPanel
84113 0 DuctAdapter
941131 BottomFrame
10 4113 2 SupportLeg
11 4113 3 WheelShaft
12 4113 4 Plate,FanThermostat
13 4113 5 OverheatLimitSwitch(Inner)
14 4113 6 CooldownThermostat
15 4113 7 OverheatLimitSwitch,AirOutlet(PETE)
16 4113 8 MetalBracket,orBulb
17 4113 9 Wheel
18 4114 0 LockingWasher
19 41141 Gasket,Rubber
20 4114 2 HeatingElement(15PerHeater)
21 4114 3 GuardRing,Rubber
24 4114 4 RearPanel
25 4114 5 PartitionPanel/Bracket
26 4114 6 ContactorMountingPlate
28 4114 7 MountingPlate,FanMotor
29 4114 8 FanGuardGrill
# P/N DESCRIPTION
30 4114 9 Bushing,Medium
31 4115 0 Bushing,Large
32 41151 Contactor(3PerHeater)
S/Npriorto2142use41152
33 4115 2 Contactor(1PerHeater)
34 4115 3 StrainReliever(Qty2)
35 4115 4 ToggleSwitch
36 4115 5 FuseHolder
36A 4115 6 Fuse
37 4115 7 TerminalBlock
38 4115 8 Transformer
39 4115 9 LockingClamp+EndPlate
40 4116 0 PlasticBracket
41 41161 AmbientThermostat(KnobNotIncluded)
S/N2022&Beyond
42 4116 2 ThermostatKnob(For180017)
4116 3 ThermostatKnob(For20220)
43 4116 4 GroundBolt
45 4116 5 FanMotor
47 4116 6 FanBlade
48 4116 7 Bushing,Small
41168† Duct(14”x25’long)
4116 9 † BracketforTerminalBlock
†NotShown
WARNING: USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR
DEATH. REPLACEMENT PARTS ARE ONLY AVAILABLE DIRECT FROM THE FACTORY AND MUST BE INSTALLED BY A QUALIFIED
SERVICE AGENCY.

10
HEATSTAR Electric Construction Heater Operating Instructions and Owner’s Manual
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
# P/N DESCRIPTION
141161 AmbientThermostat
241151 Contactor,3-Pole(S/Npriorto2142use41152)
2A 4115 2 Contactor,4-Pole
34115 4 ToggleSwitch
44113 7 OverheatLimitSwitch(PETE)
54115 7 TerminalBlock
# P/N DESCRIPTION
64115 8 Transformer(PETR)
74115 6 Fuse
84114 2 HeatingElement
94113 5 OverheatLimitSwitch(Inner)
10 4113 6 CooldownThermostat
11 4116 5 FanMotor
CONTROL BOX HSP40E
3
3
3
7
2
4
6
5
2A
2
2
8
9
4
10
1
11
WARNING: USE ONLY MANUFACTURER’S REPLACEMENT PARTS. USE OF ANY OTHER PARTS COULD CAUSE INJURY OR
DEATH. REPLACEMENT PARTS ARE ONLY AVAILABLE DIRECT FROM THE FACTORY AND MUST BE INSTALLED BY A QUALIFIED
SERVICE AGENCY.

Operating Instructions and Owner’s Manual
11
HEATSTAR Electric Construction Heater
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
NOTES:

OPERATING INSTRUCTIONS
AND OWNER’S MANUAL
Model#
HSP40E
NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!NEVER LEAVE THE HEATER UNATTENDED WHILE BURNING!
HeatstarProducts,Inc.reservestherighttomakechangesatanytime,without
noticeorobligation,incolors,specifications,accessories,materialsandmodels.
WARNING:
USEONLYMANUFACTURER’SREPLACEMENTPARTS.USEOFANYOTHERPARTS
COULDCAUSEINJURYORDEATH.REPLACEMENTPARTSAREONLYAVAILABLE
DIRECTFROMTHEFACTORYANDMUSTBEINSTALLEDBYAQUALIFIEDSERVICE
AGENCY.
PARTS ORDERING INFORMATION:
PURCHASING: AccessoriesmaybepurchasedatanyHEATSTARbyENERCOlocal
dealerordirectfromthefactory
FOR INFORMATION REGARDING SERVICE
PleasecallToll-Free866-447-2194
www.heatstarbyenerco.com
Ourofficehoursare8:00AM–5:00PM,EST,MondaythroughFriday.
Pleaseincludethemodelnumber,dateofpurchase,anddescriptionofproblemin
allcommunication.
LIMITED WARRANTY
EnercoTechnicalProducts,Inc.warrantsitsheatersandaccessoriestobefreefrom
defectsinmaterialandworkmanshipforaperiodof1yearfromdateofpurchase.
EnercoTechnicalProducts,Inc.willrepairorreplacethisproductfreeofcharge
ifithasbeenproventobedefectivewithinthe1-yearperiod,andisreturnedat
customerexpensewithproofofpurchasetoEnercoTechnicalProducts,Inc.within
thewarrantyperiod.
Somestatesdonotallowtheexclusionorlimitationofincidentalorconsequential
damages,sotheabovelimitationorexclusionmaynotapplytoyou.ThisWarranty
givesyouspecificlegalrights,andyoumayhaveotherrightswhichvaryfromstate
tostate.
HEATSTARbyENERCO,4560W.160THST.,CLEVELAND,OHIO44135
866-447-2194
©2019,EnercoTechnicalProducts,Inc.Allrightsreserved
PRODUCTREGISTRATION:Thankyouforyourpurchase.
Pleaselogintohttp://www.egiregistration.comtoregisteryourproduct.