Heatstore HS5610 User manual

Issue 1 0216
IMPORTANT SAFEGUARDS
WHEN USING ANY ELECTRICAL APPLIANCE, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED.
PLEASE READ ALL INSTRUCTIONS CAREFULLY
AND RETAIN FOR FUTURE REFERENCE
IF IN ANY DOUBT ABOUT THE INSTALLATION OR USE OF THIS
PRODUCT, CONSULT A COMPETENT ELECTRICIAN.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling advice.
Operation
After washing hands shake off excess water droplets.
Place hands approx 120mm under the air outlet, the infra-red sensor will
automatically activate the unit.
During drying, rub your hands to aid the drying time. The nearer your
hands are to the unit, the more efficient the drying will be.
Remove hands when dry.
After 3 seconds, the unit will automatically stop running.
After 60 seconds continuous drying, the unit will stop and will need to be
reactivated if further drying is required.
Cleaning and maintenance
It is recommended that all surfaces of the HS5610 hand dryer are cleaned
regularly using a soft cloth and a non-abrasive/non-caustic cleaning fluid.
If the unit malfunctions, consult a competent electrician or the Heatstore
Technical department for advice where the unit is under warranty.
EXCHANGE
Telephone: [phone] Fax: [phone]
Victoria Road, Avonmouth, Bristol BS11 9DB
www.heatstore.co.uk
HS5610 Hi-Speed Hand Dryer
Installation and Operating Instructions
SPECIFICATION: HS5610
Electrical: 220-240V, 1800W, ~50/60Hz;
Air Speed: 90 m/s;
Drying Time: 10 seconds;
Dimensions/Weight: 320 x 290 x 170 mm; 5.5kG
IP
X1
ZONE
U
HS5610
HS5610[16]instructions 9/2/16 10:02 Page 1

32
Important Safety Information
– Please Read before Proceeding
The information contained in these installation
instructions must be read carefully before any attempt
to install the hand dryer.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Failure to accurately follow these instructions may
result in the incorrect operation of the unit, damage to
property and/or personal injury.
Heatstore will not be held liable for any damage to
property or personal injury as a result of failure to
comply with the instructions contained herein.
All electrical installation and repair work should be
carried out by a qualified electrician in accordance
with current UK IEE regulations and any local codes or
regulations.
Any maintenance to this appliance should be carried
out by a qualified electrician.
Isolate power to the device before installation or
servicing.
Check that the electrical supply corresponds to that
shown on the rating plate on the device.
Not to be used for any purpose other than drying
hands.
HS5610
Before installation
Be sure to select a suitable position to install the
hand dryer.
Allow 400mm all around the unit for safe operation.
Do not install close to reflective worktops.
Make certain that you have all the parts and
appropriate tools for installation.
Ensure that the power is disconnected before
installation.
Installation
Electrical
The electrical supply required for this unit is (single
phase) 220V AC, 50Hz.
NOTE: a circuit breaker (RCCB) may be required in
certain installations.
installation
Firstly, remove the outer casing by undoing the two
screws in each side of the casing – see figure 1
above. And undo the power cable – inset figure 1.
Using figure 2 as a guide, offer up the backplate in
the preferred mounting position and mark the
position for the 4 holes. Drill the holes and affix wall
plugs.
Mount the backplate and fix screws, making sure to
pull the power cable through its hole in the
backplate.
Ensure the backplate is secure, re-connect the power
cable and replace the outer casing and fix screws in
each side of the casing, as shown in figure 3.
Figure 1
Figure2
Figure3
Air outlet
Sensor
Air intake
outer casing screws
HS5610[16]instructions 9/2/16 10:02 Page 2