Heatstore HS5510 User manual
Issue 1 0216
IMPORTANT SAFEGUARDS
WHEN USING ANY ELECTRICAL APPLIANCE, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED.
PLEASE READ ALL INSTRUCTIONS CAREFULLY
AND RETAIN FOR FUTURE REFERENCE
IF IN ANY DOUBT ABOUT THE INSTALLATION OR USE OF THIS
PRODUCT, CONSULT A COMPETENT ELECTRICIAN.
Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist.
Check with your local authority or retailer for recycling advice.
Operation
After washing hands shake off excess water droplets.
Place hands approx 100mm under the air outlet, the infra-red sensor will
automatically activate the unit.
During drying, rub your hands to aid the drying time. The nearer your
hands are to the unit, the more efficient the drying will be.
Remove hands when dry.
After 3 seconds, the unit will automatically stop running.
After 60 seconds continuous drying, the unit will stop and will need to be
reactivated if further drying is required.
Cleaning and maintenance
It is recommended that all surfaces of the HS5510
hand dryer are cleaned regularly using a soft cloth
and a non-abrasive/non-caustic cleaning fluid.
If the unit malfunctions, consult a competent electrician
or the Heatstore Technical department for advice
where the unit is under warranty.
Cleaning the filter
The HS5510 is fitted with a removable, cleanable air filter. Should the
performance of the unit deteriorate, or the air flow slows noticeably, the filter
needs cleaning. We suggest the power is switched off during maintenance.
Remove the filter box from behind the door on the base of the machine
– see figure 4. Take out the filter and remove any dust or dirt either by
blowing or with a small hand vacuum. DO NOT WASH THE FILTER.
When clean, replace the filter in its box and replace the box into the hand
dryer and close the door.
EXCHANGE
Telephone: 0117 923 5375 Fax: 0117 923 5374
Victoria Road, Avonmouth, Bristol BS11 9DB
www.heatstore.co.uk
HS5510 Hi-Speed Hand Dryer
Installation and Operating Instructions
SPECIFICATION: HS5510
Electrical: 220-240V, 1100W, ~50/60Hz;
Air Speed: 90 m/s; Drying Time: 10 seconds;
Dimensions/Weight: 248 x 174 x 250 mm; 4,25kG
IP
X1
ZONE
U
HS5510
Figure 4
HS5510[16]instructions 26/2/16 09:49 Page 1
32
Important Safety Information
– Please Read before Proceeding
The information contained in these installation
instructions must be read carefully before any attempt
to install the hand dryer.
This appliance is not intended for use by persons
(including children) with reduced physical, sensory or
mental capabilities, or lack of experience and
knowledge, unless they have been given supervision
or instruction concerning use of the appliance by a
person responsible for their safety.
Failure to accurately follow these instructions may
result in the incorrect operation of the unit, damage to
property and/or personal injury.
Heatstore will not be held liable for any damage to
property or personal injury as a result of failure to
comply with the instructions contained herein.
All electrical installation and repair work should be
carried out by a qualified electrician in accordance
with current UK IEE regulations and any local codes or
regulations.
Any maintenance to this appliance should be carried
out by a qualified electrician.
Isolate power to the device before installation or
servicing.
Check that the electrical supply corresponds to that
shown on the rating plate on the device.
Not to be used for any purpose other than drying
hands.
HS5510
Before installation
Select a suitable position to install the hand dryer.
Allow 400mm all around the unit for safe
operation. Do not install close to reflective
worktops.
Make certain that you have all the parts and
appropriate tools for installation.
Ensure that the power is disconnected before
installation.
Installation
Electrical
The electrical supply required for this unit is (single
phase) 220V AC, 50Hz. NOTE: a circuit breaker
(RCCB) may be required in certain installations.
installation
Firstly, remove the outer casing by undoing the two
screws in the bottom of the casing – see figure 1
above. And undo the power cable – inset figure 1.
Using figure 2 as a guide, offer up the backplate in
the preferred mounting position and mark the
position for the 4 holes. Drill the holes and affix
wall plugs.
Mount the backplate and fix screws, making sure to
pull the power cable through its hole in the
backplate.
Ensure the backplate is secure and re-connect the
power cable. Replace the outer casing by firstly aligning the bottom of the
cover and then tapping the top of the cover into position by hand, then fix
the screws in the bottom of the casing, as shown in figure 3.
Power Switch Location
Figure 3
Figure 2
Figure 1
HS5510[16]instructions 26/2/16 09:49 Page 2
Other Heatstore Dryer manuals
