Heatstore TORNADO S User manual

IMPORTANT SAFEGUARDS
WHEN USING ANY ELECTRICAL APPLIANCE, BASIC SAFETY
PRECAUTIONS SHOULD ALWAYS BE FOLLOWED.
PLEASE READ ALL INSTRUCTIONS CAREFULLY
AND RETAIN FOR FUTURE REFERENCE
IF IN ANY DOUBT ABOUT THE INSTALLATION OR USE OF THIS
PRODUCT, CONSULT A COMPETENT ELECTRICIAN.
HS5900 Tornado S
Hi-Speed Hand Dryer
Operating Instructions
Telephone: [phone] Fax: [phone]
Unit 12, Access 18, Bristol BS11 8HT
www.heatstore.co.uk
ISSUE 1/0318
SPECIFICATION: HEATSTORE TORNADO S
Electrical: Cool: 800W or hot:1650W; 220/240V; 50Hz;
Air Speed: 95m/s ±5%;
Drying Time: 5-10 seconds;
Dimensions/Weight: 730(h) x 300(w) x 222 mm; 13kG
Sound level: 75dB
This marking indicates that this product should not be disposed with other household
wastes throughout the EU. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of
material resources. To return your used device, please use the return and collection systems
or contact the retailer where the product was purchased. They can take this product for
environmental safe recycling.

23
Technical Data:
Rated voltage AC 220-240V
AC 110/127V
WATERPROOF
GRADE
IPX4
Rated frequency 50/60HZ Heating conditions Ambient temperature <23
Rated power 1650W Air speed 95m/s
Motor power 800W Drying time 5-10s
Weight 13KG Overall size(mm) 300x222x730
Important Safety Warnings
injury can occur if used improperly
The HS5900 TORNADO S is a stylish stainless steel, hi-speed hand dryer with
auto-element switching and tamper-proof controls.
The information contained in these installation instructions must be read carefully
before any attempt to install the hand dryer.
Failure to accurately follow these instructions may result in the incorrect operation of
the unit, damage to property and/or personal injury.
Heatstore will not be held liable for any damage to property or personal injury as a
result of failure to comply with the instructions contained herein.
All electrical installation and repair work should be carried out by a qualified
electrician in accordance with current UK IEE regulations and any local codes or
regulations.
Any maintenance to this appliance should be carried out by a qualified electrician.
This product must be earthed.
Isolate power to the device before installation or servicing.
Check that the electrical supply corresponds to that shown on the rating plate on the
device.
NOT to be used for any purpose other than drying hands.
Important Safety Information – Please Read before Proceeding
Prohibited
Don’t open the front panel.
Components:
Cover
Key
Wall Bracket
Screws
Plugs
Air Filter
Body
Draininage
Tank
Power Switch

45
Installation:Installation:

67
Before installation
Be sure to select a suitable position where the unit is easy to use, and away from direct sunlight,
high condensation or corrosive elements. Choose a flat surface, away from high traffic. The unit
is IPX4 rated.
Make certain that you have all the parts and appropriate tools for installation.
Be sure that the electrical supply (via a switched fuse spur/connection box to which you intend to
connect the device) has been isolated/switched off to reduce the risk of electric shock.
Ensure that there is no pipe work or electrical cables located directly within the drilling area.
All pole-disconnection must be incorporated in the fixed wiring in accordance with applicable
wiring regulations.
Installation: Drying your hands:
Maintenance and cleaning
Note: Always switch the unit off before cleaning or disconnect the unit from the electrical
supply before completing any maintenance.
From time to time you will need to empty the water tank located at the front/bottom of the
machine. Simply grasp the tank by the handle and pull out. Then empty and replace the
tank before further use.
To prevent any potential clogging, pour 200cc (around 1 cup) of water through the
drain hole to fl ush.
Pull the drain tank out horizontally to ensure water does not spill.
Remove the cover in the direction indicated, and empty.
Wash out the interior with warm soapy water and dry.
Close the water tank cover, and re- fi t to the unit, making sure it is fi rmly seated.
Emptying the water tank
Shake off excess water before inserting your hands into the unit.
Step 1
Insert your hands into the unit with your fingers slightly spread. The hand dryer will start
automatically as you do this.
Step 2
Slowly withdraw your spread fingers; you will feel the powerful air flow pressing against your
hands as you do this.
Step 3
If your hands still feel wet repeat the first two steps.
Installation
Note
This unit is equipped so that it can blow hot and cool air when in operation.
Electrical
Use a single-phase alternating current 220V-240V power supply.
This unit comes pre-wired ready for installation.
The left side of the unit must be at least 150mm away from any walls to allow access to the control
panel. Before ‘offering up’ the backplate and marking the wall.