HECKLER AV Credenza Mini H891 User manual

9/15/22, 9:54 AM
H891 Heckler AV Credenza Mini
https://heckler.notion.site/H891-Heckler-AV-Credenza-Mini-1f0d3ded48d24d04aaf6513838651a72
1/15
H891 Heckler AV Credenza
Mini
In the box
Tools needed
Install wall anchors
How to install a Snaptoggle wall anchors
Mount devices and cabling
Install credenza body
Install camera bracket for Logitech Rally Bar & Rally Bar Mini
Install camera bracket for Google Meet Series One Room Kit
Install camera bracket for PTZ cameras
Install front panel
In the box
A. 1 x main body (R502-1)
B. 1 x front panel (R509)
C. 1 x mounting bracket for Rally Bar & Rally Bar Mini (R502-2)
D. 2 x mounting bracket for Google Meet Series One Room Kit Audio Bar (R502-3)
E. 1 x wall-mounting template (K394)
F. 2 x mounting screw for camera brackets (F036)

9/15/22, 9:54 AM
H891 Heckler AV Credenza Mini
https://heckler.notion.site/H891-Heckler-AV-Credenza-Mini-1f0d3ded48d24d04aaf6513838651a72
2/15
G. 2 x mounting screw for Rally Bar & Rally Bar Mini (F038)
H. 2 x mounting screw for Google Meet Series One Room Kit Audio Bar (F775)
I. 1 x hex key for installing camera brackets (F776)
J. 1 x set screw for mounting PTZ cameras (F040)
K. 1 x wingnut for mounting PTZ cameras (F041)
L. 1 x spacer for mounting PTZ cameras (F042)
M. 4 x screw for mounting VESA-compatible NUCs (F869)
N. 4 x thumb nut for mounting VESA-compatible NUCs (F838)
O. 4 x drywall-mounting screw (F039)
P. 4 x drywall-mounting washer (F035)
Q. 4 x drywall-mounting spacer (F034)
R. 4 x drywall-mounting wall anchor (F037)
S. 5-foot roll of hook & loop strap (F947)
T. 5 x strapping buckle (F751)
U. 2 x key (F033)
Keys for all Heckler AV Credenza Mini’s are identical and interchangeable.

9/15/22, 9:54 AM
H891 Heckler AV Credenza Mini
https://heckler.notion.site/H891-Heckler-AV-Credenza-Mini-1f0d3ded48d24d04aaf6513838651a72
3/15
Tools needed
•Power drill
•1/2-inch drill bit
•Philips screwdriver
•Masking tape
•Level
•Tape measure
•Stud finder
Install wall anchors
Tape the wall-mounting template(E) to the wall. Use a level.

9/15/22, 9:54 AM
H891 Heckler AV Credenza Mini
https://heckler.notion.site/H891-Heckler-AV-Credenza-Mini-1f0d3ded48d24d04aaf6513838651a72
4/15
We recommend mounting the credenza with its top surface at 36 inches
above the finished floor (AFF). This aligns the credenza well with wall outlets
at 18 inches AFF.
Mark the locations of wall studs on the mounting template.
The weight of AV Credenza Mini does not require mounting to wall studs.
The wall-mounting hole pattern is designed to enable you to mount the
credenza to your preferred wall location while mounting exclusively to
drywall.
Mark the hole locations on the wall. Select one hole location for each corner of the
credenza.
Remove the template from the wall.
Drill holes in the drywall. Use a 1/2-inch diameter drill bit.
Install the wall anchors(R).
How to install a Snaptoggle wall anchors
Pass the wall mounting screws(O) and washers(P) through the white nylon
spacers(Q), then fasten loosely into the wall in the upper left and upper right
mounting positions.
Do not fully tighten the screws during this step.

9/15/22, 9:54 AM
H891 Heckler AV Credenza Mini
https://heckler.notion.site/H891-Heckler-AV-Credenza-Mini-1f0d3ded48d24d04aaf6513838651a72
5/15
Mount devices and cabling
You can mount devices and cabling before or after mounting the credenza
to the wall
Cut the provided hook & loop straps(S) to length as you needed for strapping
components and cable management.
Use buckles(T) to firmly strap components.
Strap components to the grid of large rectangular holes on the rear and bottom
surfaces of the credenza body.

9/15/22, 9:54 AM
H891 Heckler AV Credenza Mini
https://heckler.notion.site/H891-Heckler-AV-Credenza-Mini-1f0d3ded48d24d04aaf6513838651a72
6/15
Fasten NUCs and other VESA-compatible devices to the VESA-compatible M4
clearance holes located between the large rectangular hole. M4 mounting hardware
included(M and N).
Install credenza body
Hang the credenza on the top two anchor screws.

9/15/22, 9:54 AM
H891 Heckler AV Credenza Mini
https://heckler.notion.site/H891-Heckler-AV-Credenza-Mini-1f0d3ded48d24d04aaf6513838651a72
7/15
Fasten mounting screws(O) and washers(P) through the lower corners of the
credenza body. Position a white nylon spacer(Q) between the body and the wall in
each lower corner.
Do not tighten the mounting screws.

9/15/22, 9:54 AM
H891 Heckler AV Credenza Mini
https://heckler.notion.site/H891-Heckler-AV-Credenza-Mini-1f0d3ded48d24d04aaf6513838651a72
8/15
Install camera bracket for Logitech Rally Bar & Rally
Bar Mini
Fasten the bracket(C) to Rally Bar with the 1/4-20 screws(G) and key(I) provided.

9/15/22, 9:54 AM
H891 Heckler AV Credenza Mini
https://heckler.notion.site/H891-Heckler-AV-Credenza-Mini-1f0d3ded48d24d04aaf6513838651a72
9/15
Fasten mounting screws(F) to the bracket with key(I) provided. Do not tighten the
screws at this step.
This is a good opportunity to connect all cables to the Rally Bar and install
its rear hatch.
Slide the bracket’s mounting screws into the horizontal keyhole slots on the back
wall of the credenza.
Tighten the screws with the provided hex key(I).

9/15/22, 9:54 AM
H891 Heckler AV Credenza Mini
https://heckler.notion.site/H891-Heckler-AV-Credenza-Mini-1f0d3ded48d24d04aaf6513838651a72
10/15
Install camera bracket for Google Meet Series One
Room Kit
Fasten the pair of Google Meet mounting brackets(D) to the Google Meet Audio Bar
with provided screws(H) and hex key(I). the upper corners of the main body. Position
each bracket so the cork liner rests on the top surface of the credenza body.
Fasten mounting screws(F) to the bracket with key(I) provided. Do not tighten the
screws at this step.

9/15/22, 9:54 AM
H891 Heckler AV Credenza Mini
https://heckler.notion.site/H891-Heckler-AV-Credenza-Mini-1f0d3ded48d24d04aaf6513838651a72
11/15
Slide the bracket’s mounting screws into the horizontal keyhole slots on the back
wall of the credenza.
Tighten the screws with the provided hex key.

9/15/22, 9:54 AM
H891 Heckler AV Credenza Mini
https://heckler.notion.site/H891-Heckler-AV-Credenza-Mini-1f0d3ded48d24d04aaf6513838651a72
12/15
This image couldn't be loaded.
Learn more
s3.us-west-2.amazonaws.com
Install camera bracket for PTZ cameras
Use the slot on the top surface of the credenza for mounting cameras with
1/4-20 mounting holes on their bottom surface.
Fasten the provided 1/4-20 set screw(J) and black spacer(L) into your camera.

9/15/22, 9:54 AM
H891 Heckler AV Credenza Mini
https://heckler.notion.site/H891-Heckler-AV-Credenza-Mini-1f0d3ded48d24d04aaf6513838651a72
13/15
Place the camera on the top surface. Use the black spacer provided to lift the
camera from the top surface a small distance. Fasten the camera to the credenza
body with the provided wing nut(K).
This space enables the front panel to be installed and removed.
Install front panel
Lower the front panel onto the body. Rest the four posts on the panel onto the four
hooks on the main body.

9/15/22, 9:54 AM
H891 Heckler AV Credenza Mini
https://heckler.notion.site/H891-Heckler-AV-Credenza-Mini-1f0d3ded48d24d04aaf6513838651a72
14/15
This image couldn't be loaded.
Learn more
s3.us-west-2.amazonaws.com

9/15/22, 9:54 AM
H891 Heckler AV Credenza Mini
https://heckler.notion.site/H891-Heckler-AV-Credenza-Mini-1f0d3ded48d24d04aaf6513838651a72
15/15
Use the provided keys(U) to turn the cam lock on the underside of the credenza
body.
Keys for all Heckler AV Credenza Mini’s are identical and interchangeable.
The locking feature is a low-security feature intended to reduce end-user
tampering.