HECKLER H563 User manual

H563 - Koala Kiosk Stand
for iPad Pro 12.9-inch (3rd Gen)
For support, please contact Heckler.
[e-mail].
844-432-5930
All manuals and user guides at all-guides.com

all-guides.com

2
IN THE BOX
Koala Kiosk Stand
1 x
USB-C hub with USB-C
Charge Cable and Audio Cable
1 x
Hex Assembly Key
1 x
Torx Assembly Key
1 x
Mounting Hardware
2 x
Alcohol Pad
2 x
CAT 6 Ethernet Cable
1 x
All manuals and user guides at all-guides.com

3
COMPONENTS NEEDED
(Not Included)
OPTIONAL COMPONENTS
(Not Included)
TOOLS NEEDED
(Not Included)
CAT 6, 6e, or 7
Ethernet Cable
Square Reader WiFi Texas GAT-USBC - POE+
Splitter for USB Type C
iPad Pro 12.9-inch (3rd Gen)Square Contactless
Reader
Apple 18W USB-C
Power Adapter
Included with your iPad
Pro 12.9-inch (3rd Gen)
MicroUSB Cable for
Square Contactless Reader
Apple USB-C Charging Cable
Included with your iPad
Pro 12.9-inch (3rd Gen)
Used when providing the kiosk power
and data via Power-Over-Ethernet
3/4” Drill Bit
Tape Measure Power Drill
Pen 1/4” Drill Bit
All manuals and user guides at all-guides.com

STEP 1
Remove back hatch.
4
All manuals and user guides at all-guides.com

STEP 2
Determine how to mount Kiosk Stand.
Without Base plate With Base plate
5
OR
Skip ahead to step 6
All manuals and user guides at all-guides.com

Use the Hex Assembly Key to remove
two srews from base plate.
6
STEP 3
Disassemble base plate.
All manuals and user guides at all-guides.com

all-guides.com

Drill two 1/4" holes and one 3/4" center hole
4.45
7
STEP 4
Drill mounting holes in table top.
4.45”
1”
2”
Table front edge
Table Top
All manuals and user guides at all-guides.com

8
STEP 5
Install mounting hardware.
All manuals and user guides at all-guides.com

STEP 6
Remove front bezel.
9
All manuals and user guides at all-guides.com

Make sure the iPad orientation is correct. The sleep/wake button
should be positioned in the lower right corner. Route the USB-C
cable as shown.
10
STEP 7
Install iPad Pro and connect USB-C cable.
All manuals and user guides at all-guides.com

The front bezel is asymmetric.
Position the bezel as shown.
11
STEP 8
Reinstall front bezel.
All manuals and user guides at all-guides.com

all-guides.com

12
STEP 9
Install Square Contactless Reader
and route its Micro USB Cable. 1. Route the Micro USB Cable
2. Use Alcohol Pad to clean the
bottom of Square Contactless Reader.
3. Adhere Square Contactless
Reader to bracket.
4. Slide bracket in place,
tighten thumb nut.
All manuals and user guides at all-guides.com

13
STEP 10
Connect cables to USB-C hub
USB Port
USB-C Port
Audio Port
All manuals and user guides at all-guides.com

14
STEP 11
Organize cables and USB-C Hub inside
neck and reinstall back hatch.
All manuals and user guides at all-guides.com

15
STEP 12
Select your data and power solution.
Conventional AC Power
and Networking
PoE+ Networking
Apple Power Adapter
(USB-C)
Conventional
Network Switch
PoE+ Network Switch
OR
WiFi Texas GAT-USBC - POE+
Splitter for USB Type C
PowerData
All manuals and user guides at all-guides.com