Hella marine 2LT 980 740 Series User manual

Hella marine LED products offer many advantages over conventional bulb lamps. Signicantly reduced power consumption, ultra long life
and high tolerance to shock and vibration make the LED lamps the ideal choice for the harsh marine environment.
www.hellamarine.com
INSTRUCTION SHEET: Sea Hawk-XLR LED Deck Floodlight
for: 2LT 980 740-xxx
Product specications:
Light Source LED
Light Output ~1500 lumens (White) / ~1250 lumens (Warm White)
Colour Temperature 5000K (White) / 3000K (Warm White)
Operating Voltage MultivoltTM 9-33V DC
Power Consumption 18W (1.5A @ 12V / 0.75A @ 24V) on High and 2W on Low.
Cable Pre-wired with tinned marine cable
Housing Material 'Non-metal' thermally conductive housing
Lens Material Heavy duty Grilamid®
Bracket Material Polished 316 stainless steel
Degree of Protection IP 67 – Completely sealed
Cable Colour Connect to Function
Red Positive (+) High mode
Blue or Brown Positive (+) Low Mode
Black or White Negative (-)
Dimensions
a = 170mm / 6.69”
b = 68mm / 2.68”
c = 58mm / 2.28”
d = 55mm / 2.17”
e = 120mm / 4.72”
f = 154mm / 6.06”
g = 30mm / 1.18”
c
d
b
a
b
f
e
g
g
Dimensions
a = 170mm / 6.69”
b = 68mm / 2.68”
c = 58mm / 2.28”
d = 55mm / 2.17”
e = 120mm / 4.72”
f = 154mm / 6.06”
g = 30mm / 1.18”
c
d
b
a
b
f
e
g
g
Angle adjustment
Once the lamp is installed, the swivel resistance can be
adjusted by gradually tightening the end cap screws located on
each side. It is important that both friction mounts are adjusted to
apply similar friction and that the screws are not over tightened.
LED modules are polarity conscious. Reverse polarity will not damage this product but will inhibit its function. HELLA recommends wire
connections be soldered, and heat shrink tubing applied to seal the joint. Lamp must be protected by a fuse rated at 5 amperes maximum.
Designed and Manufactured in New Zealand
Option 1
2 x On/O Switches
Option 2
1 x On/O/On switch (Double Pole)
+_
+_
Red = High
Blue / Brown = Low
Black / White = Neg
Red = High
Blue / Brown = Low
Black / White = Neg
Option 1
2 x On/O Switches
Option 2
1 x On/O/On switch (Double Pole)
+_
+_
Red = High
Blue / Brown = Low
Black / White = Neg
Red = High
Blue / Brown = Low
Black / White = Neg
Electromagnetic Compatibility (EMC)
This LED lamp is an electronic device. The electrical circuits contain components that suppress possible interference, both emission as
well as susceptibility, to the limits prescribed in international regulations.
Wiring and High / Low mode activation
The lamp defaults to High mode when positive (Red) and negative (Black or White) cables are connected. To activate Low mode, connect
both Red and Blue or Brown cables to positive and the Black or White cable to negative. Switching between Low and High can be achieved
via two ON / OFF switches (see Option 1), a double pole ON / OFF / ON switch (see Option 2) or a headlamp type OFF / ON / ON (both) switch.
958 315-16 / 06.19
Warranty / Garantie / Garantie
ENGLISH
Congratulations! The product you have selected comes from HELLA – one of the world's leading manufacturers of lighting products.
The product comes with a 5 year warranty from end user purchase covering faults in materials, components or workmanship.
In the unlikely event that you should experience a conrmed warranty related problem with your purchase, HELLA will, at its discretion, either
repair, replace or refund the purchase price of the product. Warranty services may be obtained by returning the product within the warranty
period to the HELLA dealer where the product was originally purchased.
This warranty is in addition to and does not preclude any other rights or remedies available to the consumer under any local legislation related
to the provision of goods or services.
Our goods come with guarantees that cannot be excluded under the Australian Consumer Law. You are entitled to a replacement
or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to
have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.
This warranty does not cover:
1. Claim/s as a result of normal wear and tear or of any modications and / or alterations to the product in any shape or form.
2. Claim/s as a result of non-compliance of the assembly, service and operating instructions and/or any unt or improper use.
3. Any expenses incurred in the process of making the claim.
Note: For lamps sold in Australia, warranty services are provided by Hella Australia Pty Ltd., 4 Hargrave Place, Mentone, Victoria, 3194 Australia.
Customer Service 1800 061 729 email: [email protected] https://www.hella.com/hella-au/assets/media_global/IAM_Statement_of_Warranty.pdf
For general comments about HELLA'S products please contact us on E-mail at [email protected]
DEUTSCH
Herzlichen Glückwunsch! Das von Ihnen erworbene Qualitätsprodukt kommt von HELLA, einem der führenden Hersteller von
Beleuchtungssystemen weltweit, und ist mit einer Garantie von 5 Jahren ausgestattet. Diese deckt Fehler in Materialien, Komponenten
und Verarbeitung ab und gilt ab Kaufdatum.
In dem unwahrscheinlichen Fall, dass ein Produkt tatsächlich fehlerhaft ist und ein Garantiefall vorliegt, wird HELLA Ihr Produkt nach eigenem
Ermessen reparieren, ersetzen oder den Kaufpreis zurückerstatten.
Garantieleistungen können durch Rücksendung der Ware innerhalb der Garantiezeit an den HELLA-Händler, bei dem das Produkt ursprünglich
gekauft wurde, erhalten werden.
Diese Garantie gilt zusätzlich zu allen anderen Rechten oder Rechtsmitteln, die dem Verbraucher im Rahmen einer lokalen Gesetzgebung
in Bezug auf die Bereitstellung von Waren oder Dienstleistung zur Verfügung stehen und schließt diese nicht aus.
Diese Garantie gilt nicht für:
1. Ansprüche, die aus normalem Verschleiß des Produktes oder etwaigen Änderungen oder Modikationen am Produkt in irgendeiner Form entstehen.
2. Ansprüche, die als Folge aus Nichteinhaltung der Montage-, Service-, oder Bedienungsanleitung oder durch unsachgemäßen Gebrauch entstehen.
3. Jegliche Kosten, die durch Inanspruchnahme der Garantie entstehen.
Wenn Sie Fragen oder Anmerkungen zu HELLA Produkten haben, kontaktieren Sie uns bitte per E-Mail: [email protected]
FRANCAIS
Félicitations ! Le produit que vous venez d'acquérir est conçu et fabriqué par HELLA, l'un des premiers fabricants mondiaux
d'éclairage. Ce produit est couvert par une garantie de 5 ans à partir de la date d’achat par l’utilisateur nal, cette garantie couvrant
tout défaut lié à la fabrication, aux matériaux ou aux composants utilisés.
Dans l'éventualité peu probable que où rencontriez un cas avéré de garantie sur le produit acheté, HELLA pourra, à sa discrétion, soit réparer,
soit remplacer le produit ou encore rembourser celui-ci à hauteur de sa valeur d’achat.
Pour toute demande de prise en charge d'un produit sous garantie, veuillez retourner celui-ci dans les délais impartis auprès du revendeur
HELLA où l’achat a été effectué.
Cette garantie s’applique en complément et ne s’oppose pas à tous autres droits ou recours dont le consommateur pourrait bénécier au
terme de la législation locale en vigueur relative à la prestation de biens ou de services.
La garantie ne couvre pas:
1. les réclamations découlant d’une usure normale du produit ou faisant suite à toute modication ou altération du produit sous quelque forme que ce soit.
2. toute réclamation résultant du non-respect des instructions de montage, d’entretien ou d’utilisation ou encore d’un usage inadapté ou détourné du produit.
3. tout frais engendrés par la demande de prise en charge.
Pour tout commentaire ou suggestion sur les produits HELLA, nous vous invitons à nous contacter par email: [email protected]

I N S TA L L AT I O N S A N W E I S U N G : S e a H a w k - X L R L E D D e c k s c h e i n w e r f e r
für: 2LT 980 740-xxx
Les projecteurs à LED de Hella marine offrent de nombreux avantages par rapport aux projecteurs traditionnels à ampoules. Avec leur
consommation d'énergie minimale, leur durée de vie extrêmement longue et leur haute résistance aux chocs et aux vibrations, les
projecteurs à LED représentent le choix idéal face aux rigueurs du milieu marin.
www.hellamarine.com
INSTRUCTIONS DE MONTAGE: P r o j e c t e u r d e p o n t à L E D S e a H a w k - X L R
pour: 2LT 980 740-xxx
Caractéristiques du produit:
Source lumineuse: LED
Intensité lumineuse: ~1500 lumens (Blanc) / ~1250 lumens (Blanc Chaud)
Température de couleur: 5000K (Blanc) / 3000K (Blanc Chaud)
Tension de fonctionnement: MultivoltTM 9-33V DC
Consommation: 18W (1.5A @ 12V / 0.75A @ 24V) en mode "High" et 2W en mode "Low".
Cablâge: précâblé avec du câble marin
Matériau boîtier: boitier non métallique à transfert thermique
Matériau lentille: Grilamid®ultra résistant
Matériau étrier: inox 316 poli
Niveau de protection: IP 67 – complètement étanche
Couleur Raccordement Mode
Rouge Positif (+) Intensité max
Bleu ou Brun Positif (+) Economie
Noir ou Blanc Négatif (-)
Dimensions
a = 170mm / 6.69”
b = 68mm / 2.68”
c = 58mm / 2.28”
d = 55mm / 2.17”
e = 120mm / 4.72”
f = 154mm / 6.06”
g = 30mm / 1.18”
c
d
b
a
b
f
e
g
g
Dimensions
a = 170mm / 6.69”
b = 68mm / 2.68”
c = 58mm / 2.28”
d = 55mm / 2.17”
e = 120mm / 4.72”
f = 154mm / 6.06”
g = 30mm / 1.18”
c
d
b
a
b
f
e
g
g
Ajustement angulaire:
Une fois le projecteur mis en place, la résistance de pivotement
peut être ajustée en serrant progressivement les vis latérales.
Il est important que les deux plaques de friction soient ajustées de
manière identique. Eviter un serrage excessif des vis.
Les éclairages à LED ont une polarité prédéterminée. L’inversion de polarité n’endommagera pas ce produit mais ses fonctions seront
rendues inopérantes. HELLA recommande que les câbles soient soudés et qu’une gaine de protection thermorétractable soit ajoutée
pour garantir l’étanchéité. Le projecteur doit être protégé par un fusible de 5 ampères maximum.
Designé et fabriqué en Nouvelle Zelande
Option 1
2 x On/O Interrupter
Option 2
1 x On/O/On Interrupter (Biploaire)
+_
+_
Rouge = Max
Bleu / Brun = Economie
Noir / Blanc = Neg
Rouge = Max
Bleu/Brun = Economie
Noir / Blanc = Neg
Option 1
2 x On/O Interrupter
Option 2
1 x On/O/On Interrupter (Biploaire)
+_
+_
Rouge = Max
Bleu / Brun = Economie
Noir / Blanc = Neg
Rouge = Max
Bleu/Brun = Economie
Noir / Blanc = Neg
Compatibilité électromagnétique (EMC)
Cet éclairage à LED est un appareil électronique. Les circuits électriques incorporent des composants qui éliminent les
interférences potentielles, tant au niveau des émissions propres à l'appareil qu'à la susceptibilité aux émissions externes,
selon les limites prescrites par les normes internationales.
Câblage et activation des modes High / Low
L'intensité maximale (mode High) est obtenue lorsque les câbles positif (Rouge) et négatif (Noir ou Blanc) sont connectés.
Pour activer le mode Low (veilleuse), connecter les câbles Rouge et Bleu ou Brun au positif et le câble Noir ou Blanc au négatif.
3 types de branchement sont possibles: avec 2 interrupteurs ON / OFF (voir Option1), avec un interrupteur double ON / OFF / ON
(voir Option 2) ou encore un interrupteur automobile OFF / ON (1) / ON (1+2)
Dimensions
a = 170mm / 6.69”
b = 68mm / 2.68”
c = 58mm / 2.28”
d = 55mm / 2.17”
e = 120mm / 4.72”
f = 154mm / 6.06”
g = 30mm / 1.18”
c
d
b
a
b
f
e
g
g
Dimensions
a = 170mm / 6.69”
b = 68mm / 2.68”
c = 58mm / 2.28”
d = 55mm / 2.17”
e = 120mm / 4.72”
f = 154mm / 6.06”
g = 30mm / 1.18”
c
d
b
a
b
f
e
g
g
Spezifikationen:
Leuchtmittel LED
Lichtleistung ~1500 lumens (5000K Weiß) / ~1250 lumens (Warmweiß)
Farbtemperatur 5000K (weiß) / 3000K (warmweiß)
Betriebsspannung MultivoltTM 9-33V DC
Leistungsaufnahme 18W (1.5A @ 12V / 0.75A @ 24V) im High- und 2W im Low-Modus.
Kabel Vorverkabelt mit verzinntem Marinekabel
Material Gehäuse Thermisch leitfähiges, nicht-metallisches Gehäuse
Material Lichtscheibe Heavy duty Grilamid®
Material Halter Edelstahl 316 rostfrei, poliert
Schutzgrad IP 67 – Hermetisch versiegelt
www.hellamarine.com
Hella marine LED Leuchten bieten erhebliche Vorteile gegenüber herkömmlichen Laternen mit Glühlampen: Durch deutlich verringerte
Leistungsaufnahme, extrem lange Lebensdauer und Unempndlichkeit gegen Stöße und Vibrationen sind LED Leuchten ideal für hohe
Beanspruchungen im maritimen Einsatz.
Abmessungen
Farbe Verbinden mit Funktion
Rot Positiv (+) Einstellung
Hoch
Blau order Braun Positiv (+) Einstellung
Niedrig
Schwarz order
Weiß Negativ (-)
Verstellung des Neigungswinkels
Ist die Leuchte installiert, kann der Schwenkwiderstand
eingestellt werden, indem die Schrauben an den Seiten
schrittweise festgezogen werden. Es ist wichtig, dass beide
Schrauben gleich fest angezogen und nicht überdreht sind.
Bei Verpolung wird die Laterne nicht beschädigt, aber in ihrer Funktion beeinträchtigt. HELLA empehlt, alle Kabelverbindungen
zu löten und anschließend mit Schrumpfschlauch abzudichten. Die Sicherung für die Laterne sollte nicht mehr als 5 Ampere
betragen.
Designed und hergestellt in New Zealand
Option 1
2 x Ein/Ausschalter
Option 2
1 x Ein/Aus/Einschalter (Zweipolig)
+_
+_
Rot = Hoch
Blau / Braun = Niedrig
Schwarz / Weiß = Neg
Rot = Hoch
Blau / Braun = Niedrig
Schwarz / Weiß = Neg
Option 1
2 x Ein/Ausschalter
Option 2
1 x Ein/Aus/Einschalter (Zweipolig)
+_
+_
Rot = Hoch
Blau / Braun = Niedrig
Schwarz / Weiß = Neg
Rot = Hoch
Blau / Braun = Niedrig
Schwarz / Weiß = Neg
Elektromagnetische Verträglichkeit (EMV)
LED-Leuchten sind elektronische Geräte. Ihre integrierten Schaltkreise beinhalten Komponenten, die Interferenzen (sowohl Emissionen
als auch Anfälligkeit für Strahlung anderer Geräte) unterdrücken und entsprechen internationalen Bestimmungen.
Kabel und High-/Low-Modus-Aktivierung
Die Leuchte bendet sich im High-Modus, wenn das Rot Kabel mit dem Plus-Pol und das Schwarz order Weiß Kabel mit dem Minus-
Pol verbunden ist. Um den Low-Modus zu aktivieren, müssen das Rot und das Blau order Braun Kabel beide an den Plus-Pol und das
schwarz order weiß Kabel an den Minus-Pol angeschlossen werden. Es gibt drei verschiedene Möglichkeiten, um den Modus zu wechseln.
Entweder mit 2 AN / AUS-Schaltern (Option 1), einem zweipoligen AN / AUS / AN-Schalter (Option 2) oder einem AUS / AN / AN (beide)
Automobil-Schalter.
Other Hella marine Floodlight manuals
Popular Floodlight manuals by other brands

HOLOPHANE
HOLOPHANE Predator Medium Floodlight Marine Installation and maintenance manual

REMS
REMS Lumen 5000 instruction manual

Erco
Erco Trion Mounting instructions

ADJ
ADJ Boom Box FX1 User instructions

Eaton
Eaton Crouse-hinds series Installation & maintenance information

Peak Beam Systems
Peak Beam Systems Maxa Beam 400 series Operation manual