Hessaire MC92 User manual

Mobile Evaporative Cooler
Use & Care Guide
MC92
INDEX
Safety Rules..............…1
Quick Start............….…2
Features........................3
Maintenance.........….....4
Cooler Parts........……...5
Warranty.............……...6
Trouble Shooting…......7

Safety
Key Operational Points
Your cooler must be positioned in front of an
open windowor door if it isto operate effectively.
(see below picture)
1. Always ensure that there is another open
window or door through which the air can
exhaust from the room.
2. Ensure the rigid media is kept clean
throughout the use of your cooler.
3. At the end of each day run your cooler on
FAN ONLY for 30 minutes to dry out the
rigid media.
4. Prior to putting your cooler away for
winter, always:
a. Drain the tank and wipe clean.
b. Clean the rigid media.
c. Reassemble and run on FAN
ONLY for 30 minutes to dry out the rigid
media.
Indoor Use
Safety Rules
1. Read and follow all instructions, cautions,
and warnings. Failure to do so could result in
personal injury, death or property damage.
2. Unit must be in the OFF position and
UNPLUGGED from power receptacle before
performing any maintenance.
3. Make sure the electrical power source
conforms to the requirement of the evaporative
cooler(s) as well as local codes.
4. To reduce the risk of fire or electrical shock,
do not expose electrical connections to water.
5. Do not touch electrically live components.
6. Assurethat all power cords do not meet any
sharp edges, hot surfaces or chemicals.
Immediately replace any damaged parts.
CAUTION: BEFORE CLEANING OR SERVICING DISCONNECT POWER SUPPLY

Quick Start
After unpacking your evaporative cooler, carefully inspect for any damage that may have occurred
during transit. Inspect for loose, missing or damaged parts.
Contents: Evaporative cooler (1), Hardware Bag (1), Casters (4)
Tools / Materials Needed: Drill with #2 Phillip’s bit or Phillp’s head screwdriver
A
B
C
D
E
Remove the
screws from
the top, rear
panel.
Lift and pull out
bottom of the
panel to remove.
Locate the bag/box of
hardware inside the
cooler. Remove the
hardware bag/box.
Check for 4 casters,
16 bolts and a
garden hose
adapter.
Install 4 casters
1Install Casters and Front caster with lock
4 Fill cooler by
using bucket or hose
5 Turn the cooler
On and ENJOY
3 Connect to any
power supply
2 Install garden
hose adapter

Features
Control Panel
Rotary Switch for Fan
Has 4 positions. (Clockwise from OFF)
OFF, LOW, MED, HI.
Rocker Switch for Pump
Controls the pump
Rocker Switch for Swing
Controls the oscillation
Rocker Switch for POWER
Main power control. When the power is turned
to the “OFF” position, the other controls will not
work.
Tool Tray
Our coolers have a place to put your tools,
drinks and much more!
Hose Adapter
Ourconvenienthose adapter allows you tohave
continuous water fill on your cooler.
Air Intake
This cooler has 3 media panels instead of a
single panel found on most mobile coolers. 3
panels allow more air-intake area and reduce
pre-rotation of the air to the prop, which
translates into lower static pressure and more
efficient air delivery to the prop.

Cooler Maintenance
Cleaning Cooler and Rigid Media Pads
The removable panel and media pad can be
sprayed out on the ground to clean pad. Use
light pressure when sprayingpads. You can use
asoft bristlebrush to gently wipe away deposits.
NEVER spray pads with water while cooler is
operating, and fan is running. This can cause
damage to motor and will void the warranty.
Removal of the Back Panel (Disconnect power
supply before this procedure.)
Remove the screws
from the top, rear
panel.
Lift and pull down
and out on the
panel to remove
Removal and Replacement of Cooling Media
1. If your cooler includes media pins,
remove by unscrewing/pulling out the
disc.
2. Remove media pad. Replace with new
pad.
3. Reinstall the back panel and you are
ready to use the cooler again.
Go to www.hessaire.com for replacement
videos and tips for eliminating any odor.
Draining the Cooler Tank
1. Pull or unscrew drain plug/cap from drain
assembly.
2. Tip unit to ensure all water exits the unit.
3. Replace drain plug.
Use all precautions and
disconnect from power source
before performing any
maintenance.