hestan DELUXE GRILL AGCP36 Series User manual

©2019 Hestan Commercial Corporation
1
EN
COLORED PANEL
REPLACEMENT
DELUXE GRILL -
MODEL # AGCP36x / 42x
IMPORTANT - READ ALL INSTRUCTIONS BEFORE YOU BEGIN
THE INSTRUCTIONS HEREIN SHOULD BE PERFORMED BY A QUALIFIED SERVICE TECHNICIAN.
THE APPLIANCE MUST BE COMPLETELY COOL AND THE GAS SOURCE MUST BE SHUT OFF.
THE POWER MUST BE DISCONNECTED. IF AN LP TANK IS INSTALLED, REMOVE IT. REMOVE
ALL ITEMS INSIDE THE LARGE DRAWER.
Some parts inside your Deluxe Grill have sharp edges. Care must be taken
when handling the various components to avoid personal injury. Wear gloves
when handling.
TOOLS REQUIRED:
Flat and Phillips screwdrivers
1/8” Allen wrench
CART DISASSEMBLY
NOTE: Parts of the grill are very heavy. Ask a helper to provide assistance
removing the large drawer. Apply the brakes to the 2 casters.
FIG. 1
1. Fully extend the large drawer and place a block of wood beneath to support the weight of the
drawer. Using an Allen wrench, remove 3 attachment bolts on each drawer slide (red arrows)
as shown in Fig. 1. Remove the drawer from the grill cart with help from an assistant.

©2019 Hestan Commercial Corporation
2
EN
CART DISASSEMBLY (CONTINUED)
LEFT PANEL REPLACEMENT
2. As shown in Fig. 2, remove 4 screws
on the large louvered cover at the
back of the grill. Remove cover and
set aside.
Remove 4 screws for small access
panel. The grill electrical box
is attached to the inside of this
panel. Detach the 4, 8, and 1o-pin
electrical connectors at the top and
bottom of the box and remove this
assembly and set aside.
You now have access to all interior
screws securing left and right
textured panels of the cart. FIG. 2
3. When viewed from the front, remove 6 screws
shown in Fig. 3.
FIG. 3 FIG. 4
4. When viewed from the rear access areas,
remove 3 screws shown in Fig. 4.

©2019 Hestan Commercial Corporation
3
EN
LEFT PANEL REPLACEMENT (CONTINUED)
5. Remove the last 2 screws at the
left-bottom of the cart as shown
in Fig. 5. Panel should come
off by pushing from the inside
toward the exterior of the unit.
Re-assembly is the reverse
process. It is recommended to
install all screws by hand, and
NOT use a drill-driver or screw
gun. It is very easy to strip the
threaded holes.
FIG. 2
RIGHT PANEL REPLACEMENT
6. When viewed from the front,
remove 7 screws shown in Fig. 6.
FIG. 6
FIG. 7
7. When viewed from the rear access
areas, remove 3 screws shown in Fig. 7.
FIG. 5

©2019 Hestan Commercial Corporation
4
EN
RIGHT PANEL REPLACEMENT (CONTINUED)
P/N 030520 REV A
9. Lay the drawer face-down on a flat surface with a blanket or towel to protect the finish.
Remove the textured panel by removing all screws as shown in Fig. 9. There are 12-14 screws
(depending on which model grill you own). There are also 3 screws inside the drawer (Fig 10).
Re-assembly is the reverse process. It is recommended to install all screws by hand, and NOT
use a drill-driver or screw gun. It is very easy to strip the threaded holes.
8. Remove the last 3 screws at the right-
bottom of the cart as shown in Fig. 8.
Panel should come off by pushing from
the outside toward the interior of the
unit. There is a small drain hose which
also must be disconnected from inside
the panel.
Re-assembly is the reverse process. It
is recommended to install all screws
by hand, and NOT use a drill-driver or
screw gun. It is very easy to strip the
threaded holes.
FIG. 8
FRONT PANEL REPLACEMENT
FIG. 9
10. Final re-assembly is the reverse process of steps 1 & 2. Re-installing the large drawer into the
grill can be difficult without the aid of a helper. Be sure to tighten the 6 screws on the drawer
slides, then check for easy movement and proper clearances all around the drawer as you push it
back in. Remember to plug in the electrical box connections. Check for proper grill operation.
FIG. 10