hestan AGCP Series User manual

©2019 Hestan Commercial Corporation
1
EN
COLORED PANEL
REPLACEMENT
CABINETRY - AGCP SERIES
IMPORTANT - READ ALL INSTRUCTIONS BEFORE YOU BEGIN
THE INSTRUCTIONS HEREIN SHOULD BE PERFORMED BY A QUALIFIED SERVICE TECHNICIAN.
IF CABINET OR DRAWER IS NEAR AN APPLIANCE, IT MUST BE COMPLETELY COOL AND THE GAS
SOURCE MUST BE SHUT OFF. THE POWER MUST BE DISCONNECTED.
Some parts inside your cabinet or drawer have sharp edges. Care must be
taken when handling the various components to avoid personal injury. Wear
gloves when handling.
TOOLS REQUIRED:
Flat and Phillips screwdrivers
PART REPLACEMENT - TYPICAL DOOR (VARIOUS PRODUCTS)
1. Unclip door hinge from frame. Consult the
Installation Manual 009798 or 009799 which came
with your cabinet product. If door was part of a
Grill Cart, consult the manual which came with
the cart.
Remove the hinges from the back face of the door
as shown in Fig. 1.
FIG. 1
2. Lay the door on a flat surface with a blanket or
towel to protect the door finish. Remove the door
liner by removing all screws as shown in Fig. 2.
FIG. 2

©2019 Hestan Commercial Corporation
2
EN
PART REPLACEMENT - TYPICAL DOOR (CONTINUED)
PART REPLACEMENT - LIFT-OFF DOOR (AGLP)
3. Remove the textured panel insert by
removing all the internal screws as
shown in Fig. 3.
4. Re-assembly is the reverse process. It
is recommended to install all screws
by hand, and NOT use a drill-driver or
screw gun. It is very easy to strip the
threaded holes.
Re-attach and adjust doors to frame
as per Installation Manual 009798 or
009799 which came with your cabinet
product.
If the door was part of a Grill Cart,
consult the manual which came with
the cart.
FIG. 3
1. For the AGLP cabinet, remove the door by pulling straight up until the door comes off the pins
(shown here in red). Panel replacement is the same as step 2-4 in the previous section.
DOOR
PINS

©2019 Hestan Commercial Corporation
3
EN
PART REPLACEMENT - TYPICAL DRAWER
RELEASE
LEVER DRAWER
FRAME
2. Lay the drawer face-down on a flat surface with a blanket or towel to protect the finish.
Remove the drawer face from the drawer box by removing 10 screws as shown below in red.
1. To remove the drawer(s) from
the box, press the release lever
(shown here in green) on each
side of the drawer to disengage
the slide (up on the left, down
on the right), then pull the
drawer all the way out.
Cart drawers are removed in a
similar way.

©2019 Hestan Commercial Corporation
4
EN
PART REPLACEMENT - TYPICAL DRAWER (CONTINUED)
3. Remove the textured panel insert by
removing all the internal screws as
shown in Fig. 4.
4. Re-assembly is the reverse process.
It is recommended to install all
screws by hand, and NOT use a drill-
driver or screw gun. It is very easy
to strip the threaded holes.
Reinstall the drawer by aligning the
slides on either side and push the
drawer back into the opening. You
will hear the release levers click.
Open and close the drawer a few
times to check for proper function
and alignment.
FIG. 4
PART REPLACEMENT - PAPER TOWEL DISPENSER
1. For the AGPTD16 Paper Towel Dispenser, slightly close the door and remove 2 hidden screws
(shown in red) and the door stop (shown in green). The door will open further, exposing the
inner walls of the box.

©2019 Hestan Commercial Corporation
5
EN
PART REPLACEMENT - PAPER TOWEL DISPENSER (CONTINUED)
2. Reach inside to remove 2 screws at rear
edge of door, then 2 screws and handle.
The entire inner panel with towel holder
walls will come out (Fig. 5).
FIG. 5
FIG. 6
3. Remove the textured panel insert by removing
all the internal screws as shown in Fig. 6.
4. Re-assembly is the reverse process. It is
recommended to install all screws by hand, and
NOT use a drill-driver or screw gun. It is very
easy to strip the threaded holes.

©2019 Hestan Commercial Corporation
6
EN
PART REPLACEMENT - STORAGE DRAWER (AGSR30/36)
2. Lay the drawer face-down on a flat surface with a blanket or towel to protect the finish and the
handle. Remove the drawer face from the drawer box by removing 10 screws as shown below in
red. Remove 4 rubber bumpers as well.
1. To remove the drawer from
the box, press the release lever
(shown here in green) on each
side of the drawer to disengage
the slide (up on the left, down
on the right), then pull the
drawer all the way out.
4. The handle and endcaps can be transferred to
the new drawer face. Re-assembly is the reverse
process. It is recommended to install all screws
by hand, and NOT use a drill-driver or screw
gun. It is very easy to strip the threaded holes.
Reinstall the drawer by aligning the slides on
either side and push the drawer back into the
opening. You will hear the release levers click.
Open and close the drawer a few times to check
for proper function and alignment. Don’t forget
to re-install the rubber bumpers.
3. The drawer face should slide off as shown below.
The screws which secure the handle endcaps are
now accessible and can be removed.
P/N 030526 REV A