hestan GRSL24 Quick guide

24” REFRIGERATOR DRAWERS
24” OUTDOOR REFRIGERATOR RIGHT HINGE
24” OUTDOOR REFRIGERATOR LEFT HINGE
24” DUAL ZONE REFRIGERATOR WITH WINE SOLID DOOR RIGHT HINGE
24” DUAL ZONE REFRIGERATOR WITH WINE SOLID DOOR LEFT HINGE
GRR24
GRSR24
24” REFRIGERATOR / FREEZER DRAWERS
GRFR24
GRSL24
GRWSR24
GRWSL24
24” DUAL ZONE REFRIGERATOR WITH WINE GLASS DOOR RIGHT HINGE
24” DUAL ZONE REFRIGERATOR WITH WINE GLASS DOOR LEFT HINGE
24” SINGLE FAUCET BEER DISPENSER SOLID DOOR RIGHT HINGE
24” SINGLE FAUCET BEER DISPENSER SOLID DOOR LEFT HINGE
24” DOUBLE FAUCET BEER DISPENSER SOLID DOOR RIGHT HINGE
GRWGR24
GRWGL24
GFDSR241
GFDSL241
24” DOUBLE FAUCET BEER DISPENSER SOLID DOOR LEFT HINGE
GFDSL242
GFDSR242
Outdoor Refrigeration Products
Installation and Instruction
Manual
P/N 011027 rev B
Form. No. Z2424

HESTAN RESIDENTIAL INSTALLATION MANUAL
2
hestanoutdoor.com
TABLE OF CONTENTS
Warranty Information ...................................................... 2,3
Safety Information.............................................................. 4
Plumbing, Electrical and General Information.................... 4
Installation Instructions...................................................... 5
Toe Kick Installation........................................................... 7
Shelving/Drawer Adjustments ........................................... 8
CONGRATULATIONS
Congratulations on your purchase of a Hestan high quality
residential refrigeration product. Hestan’s innovative
functionality and user friendliness in just about any room of
your home, including kitchens, bedrooms, entertainment
rooms, basements and even bathrooms.
All Hestan products are built with commercial grade
stainless steel, providing you with the beauty and durability
for a lifetime of use. This installation guide will show you
how to properly install your new Hestan product.
We dedicate considerable time to ensure that our products
provide the highest level of customer satisfaction. If,
For your own protection, never return merchandise for
credit without our approval.
We thank you again for selecting a high quality Hestan
product. We hope you enjoy using it.
Model Number: _________________________________
Serial Number: _________________________________
Purchase Date: _________________________________
Dealer Name/Address:
______________________________________________
______________________________________________
______________________________________________
Phone Number: ________________________________
IMPORTANT!
Read and understand all information in this manual before attempting the installation. All
plumbing and electrical work must be performed by a qualified technician and conform to all
applicable state and local codes.
C
US
HESTAN RESIDENTIAL PRODUCTS WARRANTY
WARRANTY:
Hestan Corporation (“Hestan”) warrants to the original retail
purchaser that during the Basic Warranty Period, Hestan’s
products will be free from free from defects in material and
workmanship, and during the Extended Warranty Period,
the hermetically sealed refrigeration system contained in
Hestan’s undercounter refrigerator will be free from defects
in material and workmanship. This system consists entirely
of the compressor, condenser, drier, connecting tubing,
evaporator and hot gas bypass valve.
The Basic Warranty Period is as follows:
•
(2) year period commencing on the date of purchase
by the original retail purchaser.
The Extended Warranty Period applies only to the
hermetically sealed refrigeration system contained
in Hestan’s undercounter refrigerators. The Extended
Warranty Period is the portion of the five (5) year period
commencing on the date of purchase by the original retail
purchaser that is not covered by the Basic Warranty Period.
Door Information ................................................................ 8
Handle Installation ................................................................ 9
Door Lock Installation........................................................... 9
Wood Overlay Installation..................................................... 9
Wine Rack Trim....................................................................10
product offering gives you the opportunity to enjoy the
For a new product or floor display model. The two
however, service is required, call Hestan at 888-905-7463

3
hestanoutdoor.com
HESTAN RESIDENTIAL INSTALLATION MANUAL
This Warranty does not apply to:
• Damage to Products occurring during transportation.
• Products that are used in a manner that is not normal
residential or light commercial use.
• Products that are: improperly installed; misused or
abused; operated with low voltage; wired in a manner
not conforming to electrical codes; not properly
operated in accordance with Hestan’s instructions; not
cleaned or maintained in accordance with Hestan’s
other acts of nature.
• Consumable items such as light bulbs.
• Cosmetic damage.
• Adjustments to controls, door reversal, cleaning the
condenser or other routine maintenance.
• Products for which the original proof of purchase,
• Products for which the defective parts are not returned
for inspection if requested by Hestan.
• Damage to other property caused by the products,
including but not limited to loss of food due to spoilage
and damage caused by water leakage.
THIS LIMITED WARRANTY IS IN LIEU OF ANY OTHER
WARRANTY, EXPRESSED OR IMPLIED, INCLUDING BUT NOT
LIMITEDTO ANY IMPLIEDWARRANTY OF MERCHANTABILITY
OR FITNESS FOR A PARTICULAR PURPOSE; PROVIDED
HOWEVER, THAT TO THE EXTENT REQUIRED BY LAW,
IMPLIED WARRANTIES ARE INCLUDED BUT DO NOT EXTEND
BEYOND THE DURATION OF THE EXPRESS WARRANTY FIRST
SET ABOVE.
HESTAN’S SOLE LIABILITY AND YOUR EXCLUSIVE REMEDY
UNDERTHISWARRANTY ARE SET FORTH INTHE PARAGRAPH
ENTITLED “REMEDY” SET FORTH ABOVE.
HESTAN SHALL HAVE NO LIABILITY WHATSOEVER FOR
ANY INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES
ARISING FROM THE SALE, USE OR INSTALLATION OF THE
PRODUCT OR FROM ANY OTHER CAUSES WHATSOEVER,
WHETHER BASED ON WARRANTY (EXPRESS OR IMPLIED) OR
OTHERWISE BASED ON CONTRACT, TORT OR ANY OTHER
THEORY OF LIABILITY. IN NO EVENT SHALL HESTAN’S
LIABILITY WITH RESPECT TO A PRODUCT EXCEED THE
PURCHASE PRICE OF THE PRODUCT.
Some states do not allow limitations on how long an implied
warranty lasts, or the exclusion or limitation of incidental
or consequential damages, so the above limitations and
exclusions may not apply to you. This Warranty gives you
which vary from state to state.
REMEDY:
Hestan will provide the parts and labor necessary to repair
or replace (at Hestan’s option) any parts proven to be
defective in material or workmanship during the Basic
Warranty Period. Hestan will provide the replacement parts,
but not the labor, for any parts of the hermetically sealed
refrigeration system proven to be defective in materials
The cost of freight to ship the replacement parts will be
paid by Hestan.Replacement parts are warranted for the
remainder of the original warranty period, or ninety (90)
days, whichever is longer.
REGISTRATION:
Your Hestan product can be registered via the online
Product Registration form at www.hestanoutdoor.com.
OTHER TERMS AND CONDITIONS:
states of the United States, the District of Columbia and the
ten provinces of Canada.
To obtain the warranty coverage described in this Warranty,
Hestan or its authorized distributor or dealer must receive
written notice of the warranty claim within the applicable
warranty period. To receive parts and/or service and
the name and telephone number of the nearest Hestan
authorized service representative, please contact your
Hestan dealer or distributor, or Hestan’s Customer Service
Department by calling Hestan’s Customer Service
Department at 888-905-7463 or e-mailing Hestan’s
Customer Service Department at
[email protected].
All service provided by Hestan under this Warranty must be
performed by Hestan’s authorized service representatives,
be provided during normal business hours.
This Warranty applies only to the original retail purchaser of
the Hestan product, and may not be assigned or transferred.
instructions; modified; or damaged by lighting or
delivery date or serial number cannot be verified.
This Warranty applies only to products installed in the fifty
unless otherwise specified by Hestan in writing. Service will
specific legal rights, and you may also have other rights,
or workmanship during the Extended Warrany Period.

HESTAN RESIDENTIAL INSTALLATION MANUAL
4hestanoutdoor.com
SAFETY
PLEASE READ all instructions completely before attempting
to install or operate the unit. Take particular note of the
DANGER , WARNING and CAUTION information in the
manual. The information is important for the safe and
DANGER
Indicates a hazard that WILL result in serious injury or
death if precautions are not followed.
Indicates a hazard MAY cause serious injury or death if
precautions are not followed.
WARNING
Indicates a hazard where minor injury or product
damage may occur if precautions are not followed.
CAUTION
PRIOR TO INSTALLATION
Carefully inspect cabinet for hidden damage. If damage is
company. Hestan is not responsible for damage in transit.
When moving the unit, be sure
appropriate material to avoid damage from moving
the unit.
Do not lift unit by drawer, shelving
or door handles, as damage to the
unit could occur if not moved as instructed.
To prevent personal injury, a
minimum of two people are
required to lift the unit. Larger units may require
additional personnel.
Before moving the unit, secure the door shut with tape
to prevent door from swinging open while being moved.
Carefully move unit to installation site and place in front of
opening.
If unit has been laid on its back or
sides, place unit upright and allow
minimum of 24 hours before connecting power.
CAUTION
CAUTION
WARNING
CAUTION
PLUMBING
No plumbing connections are required. Condensate from
the cooling coil is automatically evaporated through a
condensate pan located in the condensing section of the
unit.
ELECTRICAL
A 115 volt, 60 Hz, 15 amp circuit breaker and electrical
supply are required. A separate circuit is required for each
Hestan unit installed.
Follow the National Electrical Code and any local codes or
ordinances when installing the receptacle.
All Hestan units come equipped with a NEMA 5-15P 90° plug
with a 5’ cord extending beyond the rear of the cabinet.
the wall surface for all Hestan models.
CAUTION Do not attempt to operate the
equipment on any other power
Plate attached to the unit.
efficient installation, operation and care of your unit.
The electrical outlet must be flush with, or recessed into,
discovered, file your claim immediately with the transport
to protect finished flooring with
source than that listed on the Electrical Specification

5
hestanoutdoor.com
HESTAN RESIDENTIAL INSTALLATION MANUAL
DANGER
INSTALLATION
Unit may tip forward if loaded racks/shelves are all pulled
out at the same time. To prevent tipping, and to provide
stable installation, the unit must be secured in place with
the anti-tip brackets supplied with the unit. The anti-tip
brackets, when properly installed, should secure the rear
legs/glides to the mounting surface and prevent the unit
from tipping forward.
Figure 1. 24” Anti-tip Kit
Serious Electrocution Hazard!
Electrical grounding is required.
This appliance is equipped with a 3-prong (grounding)
polarized plug for your protection against possible
shock hazards. Failure to comply with these electrical
guidelines may result in possible death or serious
• Never remove the round grounding prong from the
plug.
• Never use a 2-prong adapter.
• Never use extension cord to connect power to the unit.
• If a 2-prong receptacle is encountered, or a longer power
replaced in accordance with applicable electrical codes.
ADDITIONAL GENERAL INFORMATION
• All electrical instructions assume the outlet is located
• Floor must be level in area of installation. Leg levelers
1/2”.
NOTE: Anti-tip brackets are only used for stationary cabinets
and should not be installed on cabinets with accessory casters.
Caster kits are available for Hestan models.
Refer to the instructions supplied with the caster kit for proper
installation.
required and not included with the anti-tip kit.
provide a secure surface for attaching the brackets.
A set of anti-tip brackets is supplied with the unit. These
unit. Each bracket must be located to engage the rear
glides when the cabinet is pushed back into position. Refer
to Figure 1 (shown below) for anti-tip bracket
mounting locations.
cord is required, contract a qualified electrican to have it
4” - 10” above the floor surface.
are used for fine-tune adjustment only and should not
be used to compensate for floor differences exceeding
brackets should be attached to the floor at the rear of the
Note: Some installation sites may require modifications to
Note: If installing on a concrete floor, concrete fasteners are
injury, fire, or loss of property.

HESTAN RESIDENTIAL INSTALLATION MANUAL
6hestanoutdoor.com
PREPARING THE SPACE
If the unit is to be installed under
a countertop, it is recommended
that the countertop be supported by a structure other
than the unit itself to prevent damage to the unit.
unit is level with the surrounding
cardboard, or some other suitable material before
moving the unit into place. Failure to do this may
1). Make sure the space opening is correctly sized for
requirements:
CAUTION
CAUTION
24” Hestan Models
Height Depth Width
34-3/8” minimum,
35-1/2” maximum
24” 24”
installations to assure a full 90° opening. Allow 25” clearance
in front of unit for full door swing and shelf/drawer pull out for
all units.
2). Check that the following are level and square:
• Front and interior opening
•
• Countertop bottom front edge
To prevent possible damage to the
countertop, do not place heavy
objects on countertop directly over unit.
INSTALLING THE UNIT
1). Plug the unit into the 15 amp grounded electrical
outlet located within the installation opening. With power
applied to the unit, check that the lighting and cooling
outlet at the circuit breaker.
2). With all surfaces in the installation opening square and
level, refer to Figure 2 on page 7 and perform the following
steps to level the unit:
•
the bottom of the front edge of the countertop.
•
the rear corners.
• Adjust the unit legs so these two measurements are
equal. Using an adjustable wrench or pliers, turn legs
clockwise to lower the unit or counterclockwise to raise it.
NOTE: Legs should not extend more than 3/4” from the bottom
of the unit.
3). Slide the unit into position in the opening. Make sure
the rear leveling legs slide under the ant-tip brackets. Push
the unit into the opening until the bottom front edge of
rear legs are tight against the anti-tip brackets.
with the surrounding cabinetry. Adjust the front legs to
support the countertop at the shimmed height. Using
an adjustable wrench or pliers, turn the legs clockwise to
lower the unit or counterclockwise to raise it. Countertop
should be resting on top of the unit.
NOTE: Countertop should be resting evenly on entire top of the
unit. Shim if necessary to prevent damage to the countertop.
CAUTION
Make sure the floor under the
finished floor. Protect a finished floor with plywood
result in damage to the floor.
the unit. See chart below for finished rough opening
Installation opening and floor surface
NOTE: The floor under the unit must be at the same level as
surrounding finished floor.
functions operate properly. Turn off the power to the wall
At the front of the opening, measure from the floor to
Measure from the floor surface to the top of the unit at
the unit is flush with the surrounding cabinetry, or until the
4). Shim the front of the unit so the front face is flush
open a minimum of 90°. Use a minimum 3” filler in corner
NOTE: For a cabinet door to open properly, the door must

7
hestanoutdoor.com
HESTAN RESIDENTIAL INSTALLATION MANUAL
5). Check interior door openings to make sure the unit is
level and square. Install shelving and/or drawers. Place
the slide brackets squarely into the bracket grooves.
When installed properly, a “click” should be heard from the
slide bracket retaining tabs and the brackets should slide
smoothly. The retaining tabs will stop the shelf/drawer
when pulled out to full extension.
6). Turn on the power to the wall outlet at the circuit
breaker.
NOTE: Improper shelf/drawer installation may not actuate
slide mechanism.
Measure front of opening
from floor surface to bottom
edge of countertop
Measure at both rear corners of
unit from floor surface to bottom
of countertop
TOE PLATE INSTALLATION
Once the unit is secured in place, install the louvered toe
plate. Secure the plate by snapping the latch into the latch
catch on the unit (Figure 3).
The toe plate must be removed to
interfere with removal, and the louvered sections
must not be covered or obstructed. Obstructions could
prevent proper air circulation, which may damage the
unit.
NOTE: To achieve maximum performance, interior louver
openings and fan guard openings should never be obstructed.
CAUTION
Latch
Strike
Latch
Figure 2. Leveling the Unit
Figure 3. Toe Plate Installation
service the unit. The floor cannot

HESTAN RESIDENTIAL INSTALLATION MANUAL
8hestanoutdoor.com
SHELVING/DRAWER ADJUSTMENTS
Completely empty shelf or drawer
before removing.
1. Pull the shelf/drawer out to its furthest position. Locate
the tabs in the middle of both extenders. Lift one tab up
while pushing the opposite tab down, and pull shelf/
drawer out (Figure 4).
2. Position each bracket separately. Grasp the middle of
the bracket, pull the front end up and out, then forward
to remove it.
3. Place bracket at desired location. Push the bracket rear
hook into the rear mounting slot, then set front of the
bracket in the front slot.
4. Repeat for other brackets.
5. Push extenders completely into brackets. Align the
shelf/drawer grooves with the extenders and slide
completely into the unit.
CAUTION
Lift one tab on extender UP while
pushing tab on opposite extender DOWN
and pull out to remove.
To remove brackets,
remove shelf, lift front
of bracket to disengage
the front key slot, then
pull forward to disengage
the rear key slot.
DOOR OPTIONS
NOTE: Glass with stainless steel trim and glass with wood trim
may sweat in conditions with relative humidity over 75%.
Figure 4. Shelving/Drawer Adjustment
Hestan residential units can be converted from stainless steel
to wood overlay in the field. Solid stainless steel and stainless
steel glass doors are shipped from the factory with decorative
stainless steel panels and handles in place on the unit. All
stainless steel doors and drawers are convertible to fully
integrated models, ready to accept custom panels from your
cabinetry supplier. Templates for custom panels are available
at www.hestanoutdoor.com.
Take care in choosing the correct template for your specific
unit. Original appliance handle or custom cabinet handle can
be installed onto overlay panel.

9
hestanoutdoor.com
HESTAN RESIDENTIAL INSTALLATION MANUAL
HANDLE INSTALLATION
The handle mounting on the wood
overlay should be mounted on the
overlay only (not the actual door) to avoid damage to
the factory door.
CAUTION
DOOR LOCK INSTALLATION
NOTE: Full size lock installation wood overlay panel templates
are available on the Hestan website www.hestanoutdoor.com
Lock templates are available for all Hestan models. Take care
in choosing the
When installing to a wood overlay, perform the lock
installation before mounting the wood overlay to the
door!
1. See Figure 5 below. Attach mounting bracket to wood
overlay.
2. Insert lock body and attach with nut.
Mounting bracket
Screw
Lockwasher
Lock strike
Nut
Lock bracket
Lock body
Proper woodworking materials
and equipment should be used to
avoid damage or errors in workmanship.
CAUTION
1. Handle must be attached to the overlay before
mounting the overlay onto the door. Mark the rear of
the wood overlay panel with handle fastening locations.
2. Drill through the wood overlay panel at marked
locations, taking care not to damage the panel.
3.
with the back side of the panel. Attach the handle to the
overlay panel.
Figure 5. Installing Door Lock
Countersink screw heads so that screw heads are flush
correct template for your specific model.
WOOD OVERLAY INSTALLATION
Before beginning installation, check all components for
For best performance and
functionality, the overlay panels
should be 3/4” thick. The weight of the overlays should
not exceed 20 lbs for solid (-2) doors, 10 lbs for glass
(-4) doors, or 10 lbs for drawer (-6) models.
1. With the unit secured in position, open the door, remove
the door gasket and make sure panel pre-drilled holes
align with door frame holes.
2. Loosely attach four corners of overlay panel to the door
using #10 x 3/4” wood screws, installed through the
door frame from the rear.
3.
function. Make minor adjustments as necessary. When
panel is properly aligned, tighten mounting screws
securely. Install the rest of the mounting screws and
tighten securely.
Do not overtighten wood overlay
attachment screws, as this may
damage the factory supplied door frame.
CAUTION
CAUTION
proper fit and finish.
Check for overall wood overlay panel fit, position, and

All wine reserve racks come with sleek stainless steel fronts,
which can be removed and replaced with other wood to match
your cabinetry. See Figure 6 for wine rack face details.
WINE RACK TRIM (OPTIONAL)
HESTAN RESIDENTIAL INSTALLATION MANUAL
10 hestanoutdoor.com
Figure 6
NOTE: The unfinished faces should be finished and sealed.
In many cases, stains and / or finishes have odors that
may be objectionable in an enclosed area. Do not stain
or finish wood faces while installed on unit. To remove
the front wood face from the wine shelf, simply pull out
the wine shelf and remove the fasteners, finish as desired.

Use and Care Guide, Specification Sheets, Wood Overlay Templates for Doors, Drawers and
Grilles, and Corresponding Compliance and Energy Guides are available for download at
www.hestanoutdoor.com
Contact Hestan Customer or Technical Service at
888-905-7463
Customer Service and Technical Service are available business days
Monday through Friday from 8:00 a.m. to 5:00 p.m. PST.
P/N 011027 rev B
Form. No. Z2424