Heuresis Pb200i Alpha User manual

1
Pb200i User Guide
3/14/17
User’s Guide USA
Revision 10.0.1
Before operating the Pb200i, be sure to read this entire User’s
Guide. We strongly recommend that you store this User’s Guide
with the instrument in its carrying case.

2
Pb200i Features
Trigger
LED indicator (warning lights)
Active Measurement Area
(for sample)
Proximity button
Snout protector label
Instrument label (includes
serial numbers)
Foot stabilizer
Camera
Lanyard

3
Power On/Off button
LED/Proximity button
indicator
Power indicator
Pb200i Widget/App
Back (Return) button
Center button
Menu button
Battery door opening
CE mark
Battery wedge
Caution: removing the
Battery wedge may cause
the battery pack not to fit
correctly.
Mini USB port
Battery door

4
Charging the Batteries
The Pb200i requires 6 AA batteries. Only use rechargeable Nickel-Metal Hydride cells or disposable
Lithium Ion cells (we recommend Energizer Ultimate Lithium). Do not use alkaline batteries, as they
will not provide the proper power for the system.
1. Identify the positive and negative ends of the batteries and insert them into the smart charger.
Once the batteries are inserted correctly the LCD will turn on.
2. The batteries are fully charged when you see 4 solid bars on the LCD display and the lights are
no longer blinking. Fully charging the batteries typically takes 5-6 hours. Caution: be sure that
all six batteries are fully charged. If even one AA battery is not fully charged, it will shorten the
battery life of the battery pack.
3. Caution: We recommend using the “Refresh” button on the battery charger at least once every
two to three months. The refresh process typically takes 12 hours. There are four green refresh
buttons, one per each bank of four batteries.
4. Once the batteries are fully charged they are ready for use in the Pb200i.
5. Caution : Do not mix different manufacturer’s batteries in the Pb200i battery holder. This may
cause a reduction in your battery life.
Rechargeable NiMH (Nickel-Metal
Hydride) or disposable Lithium 6 x AA
cell battery holder
Charge indicator
LCD display Refresh button

5
Installing the Batteries
Insert the battery pack with the negative terminal facing the spring, two AA batteries per side, so that all
six chambers of the battery holder are filled (Figure1 and 2 below). Caution that the positive and negative
positions are marked on the top of the battery assembly (Figure 3). Double check that batteries make
complete contact with each other and the springs; adjust as necessary. For more information click here.
Figure 1 Figure 2 Figure 3
Remove the battery door on the bottom of the Pb200i. Slide the battery wedge to the side. Insert the
battery holder with the arrow facing the front of the instrument (Figure4). Apply slight upward force to seat
the battery holder properly; when fully inserted the battery pack should sit firmly against the battery ledge
(Figure 5). Secure the battery holder in place with the battery wedge. Replace the battery door (Figure6).
The latching mechanism will click when the battery pack is seated properly.
Caution: inserting the battery holder with the incorrect orientation will not damage the Pb200i, but the
instrument will not turn on.
Figure 4 Figure 5 Figure 6
Top; this end goes in first.

6
Powering On and Initializing the Pb Application Software
1) To power on the instrument, press and hold the Power ON/Off Button until the instrument turns
on. Caution: The instrument will go to “sleep” after 10 minutes of inactivity. Press any button to
reactivate the instrument.
2) Once the instrument has powered on, the LED will turn green and the home screen will display an
Android application displaying the “Pb” icon (Figure 7 below).
To access the application:
a. Touch the “Pb” icon on the home screen (Figure 7 below).
b. On the next screen, enter the password assigned to you by your Compliance or Safety
Officer. Touch “Login” under the “Password” text to activate the keyboard. (Figure 8
below).
c. Review the Warning Screen and confirm that you understand that the instrument
produces ionizing radiation when the safety shutter is open and the warning lights are on
(see Figure 10). If you are not familiar with the radiation safety, please press “I Do Not
Understand” and read the Radiation Safety section in this User Guide before you return
to this screen. If and when you do understand that the instrument produces ionizing
radiation when the safety shutter is open and the warning lights are on, please select the
words “I understand” to proceed to the next screen.
d. CAUTION: If you do not fully understand the warnings on the Warning Screen, please
press the Back button. Do not in proceed before you reread the Radiation Safety section
in this User Guide (see page 4).
e. On the next screen Select “Test” (Figure 10).
Figure 7 Figure 8
Figure 9 Figure 10

7
Taking a Measurement
The Pb application is designed to open and close the safety shutter of the instrument, exposing the
sample in front of the Pb200i measurement window to x-rays and gamma-rays produced by the sealed
radioisotope source in the instrument.. The safety shutter can only be opened by pulling the trigger of the
instrument when the proximity button at the top of snout of the Pb200i is fully depressed against a
surface.
1. To depress the proximity button, place the front of the instrument’s snout flat against
the sample surface. (The “Power indicator LED/Proximity button indicator” will turn
green when the proximity button is properly depressed.)
2. Pull the trigger. Caution: the proximity button must be depressed before pulling the
trigger.
When the Pb application is running on the Pb200i and the trigger is pulled with the proximity button
depressed, the shutter will open. The LEDs on the left and right side of the instrument will turn on and
emit red light. The red lights indicate that the shutter is open. If any of the conditions above are not met
during the measurement process, the shutter will close immediately and the red LEDs will shut off. Once
the shutter is open, it will remain open for a maximum of 5 minutes.
The front of the instrument’s snout should be flush against the sample surface to obtain a proper reading.
Use the foot stabilizer to balance and level the instrument directly against the surface if needed. When
the proximity button is fully depressed, the green light above the display screen will indicate that the
instrument is ready to take a measurement (Figure13).
Figure 13

8
Testing the Accuracy and Precision of the Pb200i
The Pb200i should be tested for Quality Control (QC) before each inspection, every 4 hours, and when
the inspection is complete.
1. Start by placing the wooden block on top of the Pb200i case. Hold the device with the proximity
button against the wooden reference block, with the snout of the instrument centered on the paint
film nearest 1.0 mg/cm2. When the LED turns green, squeeze and hold the trigger, keeping the
device’s snout in firm contact with the block while continuing to hold the trigger.The reading will
automatically terminate when the device has determined whether the sample is classified as Pb
paint (Positive when Pb≥1.0 mg/cm2, or Negative when Pb<1.0 mg/cm2).
2. Compare the result to the value on the reference block and make a note of the reading.
3. Complete the test 3 times, then average the readings. The average (rounded to 1 decimal place)
of the three readings must fall between 0.8 and 1.2 mg/cm2(inclusive) for the Pb200i to pass its
QC check.
Figure 13a Figure 13b Figure 13c

9
Pressing the trigger initiates the measurement. As the reading is taken, you will see the results on
the screen change to reflect the measurement data (Figure 14).
Figure 14
Once the measurement is determined to be Positive or Negative, the shutter will close, the Warning LEDs
will turn off and the result will be displayed and saved.
Typical measurement times in PCS Paint Mode take 1 to 3 nominal seconds; the closer the measured
value is to 1.0 mg/cm2, the longer the testing time will be. The maximum measurement time in PCS mode
is five nominal seconds . The results shown in the examples shown in Figure 15, 16, and 17 are based on
an action level of 1.0 mg/cm2.
Caution: The Action Level can be changed on the Pb200i by a user with administrative rights, but the
Pb200i’s Performance Characteristic Sheet (PCS) only pertains to doing HUD-based lead inspections
with an Action Level of 1.0 mg/cm2. [This is true for all XRF lead paint analyzers with PCS’s.]
Result
Standard deviation (2
sigma) Off by default
Energy spectrum for
sample Off by default
Action Level indicates “Positive”
or “Negative” result. “NULL”
indicates the reading was
terminated before a
determination could be made.
Measurement reading
time in nominal
seconds
Green vertical
bars indicate lead
Kα and Kβ peaks.
Reading/sample
number

10
Figure 15
Figure 16
“Positive” – lead present.
Result at or above the
selected Action Level.
“Negative” – lead below
selected Action Level.

11
Figure 17
Downloading Data
To download data, begin at the “Main Screen” (Figure 18). You can work your way back to the main
screen from any other screen by pressing the “Back (Return) button” until you get to the Main Screen.
CAUTION: Always export data before you plug in the mini USB cable into the instrument to
retrieve the data.
a) On the main menu, select “Readings.”
Figure 18
“Null” – Reading was
terminated before the
instrument had made a
Positive or Negative
reading. NULL readings
are not valid.

12
b) Next, select “Export Readings.” (Figure 19)
Figure 19
You can export all the readings, or you can choose a range of readings to download. Select the
readings you wish to download, then hit “Export”” (Figure 20). Once the download is complete
you will receive a confirmation (Figure 21); select “OK.” Check the indicated box if want to export
the x-ray spectrum for each reading with your results. . If you do export the spectra with the
results, you can graph the spectra in Excel. Spectra are exported as separate line items with the
results.
Caution if you check the export-spectra box, there will be two lines of data associated with each
reading. The export-spectra feature is turned off by default. The data is “exported” to a “Readings
Directory” folder (see Figure 25)
Figure 20 Figure 21

13
Transferring the Data
You can transfer data to your computer via the supplied mini USB cable or using Wi-Fi.
Using the USB Cable
To use the mini USB cable, start by removing the battery door. Insert the USB cable, making sure the
battery wedge remains in place (Figure 22).
Figure 22
Connect the USB cable to the PC. You will see this screen (Figure 23). You may also get a message on
the analyzer that reads “Allow USB Debugging?” Select “Yes.”
Figure 23

14
Double click on the internal storage icon, then double click the “Readings” folder (Figure 24).
Figure 24
Once you click on the readings file you will see a .csv file (Figure 25), as well as image files for any
photos taken with your Pb200i that were associated with readings. The .csv file contains your readings,
while the image files are named to associate them with individual readings. Drag the file(s) to your
desktop (or any other location) and double click on the file(s) to open.
Figure 25

15
Figure 26
Check to make sure all the requested data is included in the download. If it is not, unplug the
analyzer from the PC, and repeat the steps above.
*Caution – You may also use Heuresis HDMS software to export data and create reports. Please
see the HDMS manual for instructions, located on the analyzer in the “HDMS” folder.
Figure 28

16
Using Wi-Fi Connectivity
You can also use Wi-Fi to download your data. To enable Wi-Fi usage:
a) Select the “settings” icon.
Figure 28
b) Enable Wi-Fi by swiping right; the “Wi-Fi” icon will appear.
Figure 29

17
c) Find the desired network, select and connect.
Figure 30
d) Exit out using the left arrow. Shut the “settings” app off by holding the center button down until it
appears, then swipe left. Caution: Turning on Wi-Fi will decrease the battery life of the Pb200i. It
is generally a good idea to leave the Wi-Fi feature off when it is not being used.
Figure 31

18
e) Select and open the FTP Server app.
Figure 32
f) To enable the FTP server, click on the icon and swipe from off to on. Caution:The FTP server
feature will default to the “off” position for security reasons every time the instrument is turned on.
Figure 33

19
g) Place the number circled below in your web browser. The example shown here is
ftp://10.1.10.13:2121.
Figure 34
h) You will be prompted to enter a user name and password. They are the same for both — the
lowercase letters ftp. Select “Log on” after entering.
Figure 35

20
i) Your screen should look like Figure 36. Be sure to bookmark this page in your browser.
Caution:The ID number you inserted in your browser should come up each time you enable the FTP
app. In the event that it does not, simply erase the number that does and repeat steps g and h. Select the
“readings” folder.
Figure 36
j) At this next screen (Figure 37) select “readings.” You will be prompted to save the readings in a location
of your choice (.csv file format). You can open the file at this time or just save it.
Figure 37