HH Electronics SYSTEM 2 S2-210 User manual

SYSTEM 2
FULL RANGE ENCLOSURES
WITH A DETACHABLE MIXER

CONTENTS
3.Contents
4 Imp ortant Safety Instructions - English
5. Instructions Importantes De Securite - Français
6. Wichtige Sicherheitshinweise - Deusch
7. Instrucciones Importantes Para Su Seguridad - Español
8. Important Safety Instructions Pt 2.
9. Foreword
10. Introduction
11. Setting Up
12. Panel Controls
13. Media Player
14-15. Application Diagrams
16. Block Diagram & Connector Wiring
17. Specifications
18. Useful Hints and Tips
19. Legal
3

IMPORTANT SAFETY INSTRUCTIONS
Duration Per Day
in Hours
8
6
4
3
2
1 ½
1
½
¼ or less
Sound Level dBA,
slow response
90
92
95
97
100
102
105
110
115
WARNING: When using electrical products, basic cautions should always be followed, including the following:
1. Read these instructions.
2. Keep these instructions safe.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including
amplifiers) that produce heat.
9. An apparatus with Class I construction shall be connected to a mains socket outlet with a protective connection.
Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or third
prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for
replacement of the obsolete outlet.
10. Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the
point they exit from the apparatus.
11. Only use attachments/accessories provided by the manufacturer.
12. Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
13. The mains plug or appliance coupler is used as the disconnect device and shall remain readily operable. The user
should allow easy access to any mains plug, mains coupler and mains switch used in conjunction with this unit thus
making it readily operable. Unplug this apparatus during lightning storms or when unused for long periods of time.
14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in
any way, such as when power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
15. Never break off the ground pin. Connect only to a power supply of the type marked on the unit adjacent to the
power supply cord.
16. If this product is to be mounted in an equipment rack, rear support should be provided.
17. Note for UK only: If the colours of the wires in the mains lead of this unit do not correspond with the terminals
in your plug‚ proceed as follows:
a) The wire that is coloured green and yellow must be connected to the terminal that is marked by the letter E‚
the earth symbol‚ coloured green or coloured green and yellow.
b) The wire that is coloured blue must be connected to the terminal that is marked with the letter N or the
colour black.
c) The wire that is coloured brown must be connected to the terminal that is marked with the letter L or the
colour red.
18.This electrical apparatus should not be exposed to dripping or splashing and care should be taken not to place
objects containing liquids, such as vases, upon the apparatus.
19. Exposure to extremely high noise levels may cause a permanent hearing loss. Individuals vary considerably in
susceptibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently
intense noise for a sufficient time.
The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the following
permissible noise level exposures: According to OSHA, any exposure in excess of the above permissible limits could
result in some hearing loss. Earplugs or protectors to the ear canals or over the ears must be worn when operating
this amplification system in order to prevent a permanent hearing loss, if
exposure is in excess of the limits as set forth above. To ensure against
potentially dangerous exposure to high sound pressure levels, it is
recommended that all persons exposed to equipment capable of
producing high sound pressure levels such as this amplification system be
protected by hearing protectors while this unit is in operation.
4

Durée par
Jour (heures)
8
6
4
3
2
1 ½
1
½
¼ ou inférieur
INSTRUCTIONS IMPORTANTES DE SECURITE - FRANÇAIS
Niveau sonore
moyen (dBA)
90
92
95
97
100
102
105
110
115
5

Dauer pro
Tag in Stunden
8
6
4
3
2
1 ½
1
½
¼ oder weniger
GeräuschpegelldBA
langsame Reaktion
90
92
95
97
100
102
105
110
115
WICHTIGE SICHERHEITSHINWEISE - DEUTSCH
6

Duración por
Día en Horas
8
6
4
3
2
1 ½
1
½
¼ o menos
Nivel de Sonido
dBA, Respuesta Lenta
90
92
95
97
100
102
105
110
115
INSTRUCCIONES IMPORTANTES PARA SU SEGURIDAD - ESPAÑOL
7

CAUTION:
WARNING:
PRECAUCION:
ADVERTENCIA:
ATTENTION:
ADVERTISSEMENT:
VORSICHT:
ACHTUNG:
IMPORTANT SAFETY INSTRUCTIONS PT 2
After unpacking your amplifier check that it is factory fitted
with a three pin 'grounded' (or earthed) plug. Before plugging
into the power supply ensure you are connecting to a grounded
earth outlet.
If you should wish to change the factory fitted plug yourself,
ensure that the wiring convention applicable to the country
where the amplifier is to be used is strictly conformed to. As an
example in the United Kingdom the cable colour code for
connections are shown opposite.
EARTH or
GROUND
GREEN/YELLOW
NEUTRAL - BLUE
LIVE - BROWN
8

FOREWORD
Thank you for choosing to purchase an HH product.
We at HH are guided by the principle that all of our products must
balance the elements of ‘Head’ and ‘Heart: ‘Head’ is about finding the
right specifications, the right engineering solutions, the right
manufacturing techniques and of course the right price. The ‘Heart’
comes from our understanding and passion for our industry, our desire
to make interesting and relevant products, and many years of
experience using these products in their real applications.
We hope you enjoy using your product as much as we enjoyed creating
it.
By choosing HH you are joining a brand with heritage dating back to
1968, a brand that helped define the techniques and principles for
sound reinforcement and backline that still inform us today. HH
products and users dating from this time are nothing short of legendary,
a history we are proud of and constantly inspired by. Today we look
forward, reinvent and challenge ourselves constantly to build on this
history and answer current and future demands.
To register your purchase, leave your feedback and learn more about
other HH products please visit us at: www.HHelectronics.com
Thanks again.
HH Electronics
Designed and engineered with Head & Heart in the United Kingdom
9

INTRODUCTION
10
The HH System S2-210 is designed to be an all-in-one audio solution for a
wide variety of everyday applications – from classroom, dance studio to a
business seminar or any kind of musical performance
The S2-210 gives you all the ease and convenience of everything you need to
get the job done with the minimum of fuss. Its sleek detachable mixer
module offers a wide selection of inputs/outputs including a Bluetooth®
equipped media player. The pair of speaker leads and power cord that are
supplied, are all housed in their own neat clip off module. Both enclosures
include handles and 35mm pole sockets.
The HH System S2-210 – Clarity & Convenience.
This manual contains important information regarding correct and safe
operation of your active system. Please read it thoroughly in order to get
the best performance and reliability from your new HH product.

FUSE
SETTING UP
11
Access to the Mixer & accessory Modules:
Slide the catch to
the left as indicated.
Gently tilt the mixer/accessory box
then unhook from the cab.
Power and speaker connections:
The mains inlet power switch and
fuse are located to the right of the
mixer.
Mixer & Storage modules

CONTROL PANEL
10
1-4: MONO INPUT CHANNELS.
5. PEAK: Adjust the level controls and signal
level from your source(s) so the LED
illuminates only briefly on peaks in the music.
Using the system with this LED on all or
most of the time will result in poor sound
quality.
6. MIC INPUT: A balanced XLR input for
low level, low impedance devices eg. - mic
(200-600ohms) or electro-acoustic guitar.
7. LINE INPUT: an unbalanced input - for
higher output line level devices eg. -keyboard,
processor, sample/drum machine etc.
Note: Mic and Line inputs can be used
simultaneously.
8. EQ: 2 band active EQ for adjusting the
signal. Setting both controls to 0 is a good
starting point.
9. ECHO: This control determines how
much (if any) of each channel is sent
through the onboard echo FX processor -
also see (15)
10. LEVEL: Controls the channel level to the master volume - also see (22).
11. CH 5/6: A multi input line level Stereo channel. Choose from 2x 6.35mm jack, RCA or 3.5mm jack. Any
combination, or all can be used together.
12. LEVEL: Control the level of signal from channel 5/6 to the Master Volume.
13: AUX IN: Connect an audio feed from an external MP3 player or mobile phone here. Please use a stereo cable for
this. The level can be adjusted using Level control(12).
14. PHANTOM POWER: Turns on Phantom Power to all Mic channels should it be needed, eg. condenser mic’s.
15. MASTER ECHO: Control the overall level of the feed from the onboard FX processor. If you want to apply Echo
to a mono channel, first set the Master control to 5. Slowly increase the Input Echo send control until the desired amount
of echo is achieved. The Master control can then be used to control the overall Echo level.
16. MEDIA PLAYER LEVEL: Controls the overall level of music from the onboard media player. See media player
controls.
17. MONITOR OUTPUTS: A convenient way of connecting your HH S2-210 to another device such as an
additional amp/speaker setup, recording device or possibly both at the same time via the jack and RCA
connectors or 6.35mm jacks. You can also monitor this signal feed via headphones.
18. MONITOR LEVEL: Control the MONITOR OUTPUT and headphone level.
19: HEADPHONES: Connect your headphones here. The volume can be adjusted using level control (18).
20. OUTPUT LEVEL METER: Use this to give an idea of the overall output level of your HH S2-210 system. If the
LIMIT led is constantly on, reduce the MASTER VOLUME (22)
21. POWER LED: This will illuminate when the unit is powered up.
22. MASTER VOLUME: Controls the overall level of your HH S2-210 system.

MEDIA PLAYER CONTROLS
11
Use the onboard player for playing back MP3/ WMA encoded audio tracks from Micro SD
card/USB Stick or Bluetooth device. The media player is automatically powered up
when the amplifier is switched on and displays the S2-210 welcome screen
opposite.
1. SD CARD SLOT: Insert your Micro SD card here.
(Automatically detected on insertion, or if removed & reinserted uses smart
technology to resume play from the previous point).
2. MEMORY STICK SLOT: Connect your USB memory stick here.
(Automatically detected on insertion, or if removed & reinserted uses
smart technology to resume play from the previous point).
NOTE. The Media Player will play the music tracks on a USB
Stick/Micro SD Card :
in the order that they were created on the device. i.e from oldest
to newest
NOTE. The USB socket is for the playback of recorded tracks
only, not for charging a USB device.
3. LOOP: Gives 5 different options when playing tracks from an SD card or
a USB Stick :
1 - Repeat Single Track.
I - Intro.
N - One Track & then stop.
R - Random.
A - Play all in order.
4. MODE: From the welcome screen, select - Bluetooth
Hold the button in to power the player ON/OFF.
Micro SD card, USB Stick - auto detected upon insertion - if a
Micro SD Card & USB stick are inserted at the same time, use
Mode button to select either.
5. EQ: Cycle through: Normal, Pop, Rock, Jazz, Classical, Soft, DBB.
6. FD-: Folder navigate down. (Remembers the last played) not applicable
in Bluetooth mode
7. FD+: Folder navigate up. (Remembers the last played) not applicable in
Bluetooth mode
8. PREVIOUS: Press to skip to the preceding track.
9. NEXT: Press to skip to the next track.
10. PLAY/PAUSE: Use this control to play or pause your music.
11. DISPLAY SCREEN: Displays track information.
12. Device symbol dependant on what is playing.
13. Time into the track/length of the track.
14. Normal EQ setting chosen with button (5)
15. Shows the option selected via the LOOP button (3), either 1, N, R, I or A
16. Number of the track playing on the top line, number of tracks on the device on
the bottom line.
17. Bit Rate of the track currently playing - (Information only)
18. Track title.
19. EQ Bargraph display
CONNECT TO AN EXTERNAL BLUETOOTH DEVICE:
a. Select Bluetoooth via the MODE button (4), screen shows status i.e. no BT device linked yet.
b. On your Bluetooth capable device, make sure Bluetooth is enabled. Scan down the list
of available devices - search for: HH S2-210 and select. (No password required),
screen shows status i.e. Connecting...
c. Your S2-210 is now connected to your Bluetooth device which can be controlled
using the PLAY/PAUSE, PREVIOUS, NEXT & EQ BUTTONS, screen
shows status i.e. Play Music...
Only one S2-210 can be paired to your Bluetooth capable device at once, so
remember to de-select if you plan to use a different S2-210 device next time.
USB
MICROSD CARD
FD+
FD-
8
7
6
5
4
3 9
10
11
1
2
12 13 14 15 16
HH S2-210
A
17
18
19
Connecting...
BT Not Linked
Play Music...
HH S2-210
HH S2-210
HH S2-210
HH S2-210
a
b
c

14
APPLICATIONS
MP3
Solo performance.
Hard-wired
or via Bluetooth
RH SPEAKER
LH SPEAKER
CH5/6
MASTER
VOLUME
5
4
3
2
1
010
9
8
7
6
5
4
3
2
1
010
9
8
7
6
-5 +5
4 4
3 3
2 2
1 1
0
5
4
3
2
1
010
9
8
7
65
4
3
2
1
010
9
8
7
6
5
4
3
2
1
010
9
8
7
65
4
3
2
1
010
9
8
7
6
MASTER ECHO
BASS
PHANTOM
POWER
LIMIT
POWER
LINE
MIC
PEAK
TREBLE LEVEL LEVEL
L L
R R
MEDIA PLAYER
5
4
3
2
1
010
9
8
7
6
-5 +5
4 4
3 3
2 2
1 1
0
AUX IN
LEVEL LEVEL
MONITOR OUTPUTS
CH4
MP3
5
4
3
2
1
010
9
8
7
65
4
3
2
1
010
9
8
7
65
4
3
2
1
010
9
8
7
6
-5 +5
4 4
3 3
2 2
1 1
0
-5 +5
4 4
3 3
2 2
1 1
0
-5 +5
4 4
3 3
2 2
1 1
0
BASS BASS
TREBLE
LINELINE LINE
MIC MIC MIC
PEAK PEAK PEAK
TREBLE TREBLE
CH1
5
4
3
2
1
010
9
8
7
65
4
3
2
1
010
9
8
7
65
4
3
2
1
010
9
8
7
6
-5 +5
4 4
3 3
2 2
1 1
0
-5 +5
4 4
3 3
2 2
1 1
0
-5 +5
4 4
3 3
2 2
1 1
0
BASS
ECHO
LEVEL LEVEL LEVEL
CH1 CH2 CH3

15
APPLICATIONS
Full band setup.
RH SPEAKER
HOUSE PA SYSTEM.
LH SPEAKER
MASTER
VOLUME
5
4
3
2
1
010
9
8
7
65
4
3
2
1
010
9
8
7
65
4
3
2
1
010
9
8
7
65
4
3
2
1
010
9
8
7
6
5
4
3
2
1
010
9
8
7
6
-5 +5
4 4
3 3
2 2
1 1
0
-5 +5
4 4
3 3
2 2
1 1
0
-5 +5
4 4
3 3
2 2
1 1
0
-5 +5
4 4
3 3
2 2
1 1
0
5
4
3
2
1
010
9
8
7
65
4
3
2
1
010
9
8
7
6
5
4
3
2
1
010
9
8
7
65
4
3
2
1
010
9
8
7
6
MASTER ECHO
BASS BASS BASS
PHANTOM
POWER
LIMIT
POWER
TREBLE
LINELINE LINE LINE
MIC MIC MIC MIC
PEAK PEAK PEAK PEAK
TREBLE TREBLE TREBLE LEVEL LEVEL
LL
RR
CH1 MEDIA PLAYER
5
4
3
2
1
010
9
8
7
65
4
3
2
1
010
9
8
7
65
4
3
2
1
010
9
8
7
65
4
3
2
1
010
9
8
7
6
-5 +5
4 4
3 3
2 2
1 1
0
-5 +5
4 4
3 3
2 2
1 1
0
-5 +5
4 4
3 3
2 2
1 1
0
-5 +5
4 4
3 3
2 2
1 1
0
BASS
ECHO
AUX IN
LEVEL LEVEL LEVEL LEVEL LEVEL
MONITOR OUTPUTS
CH1 CH2 CH3 CH4 CH5/6

BLOCK DIAGRAM
16
1
2
2 1
+
-
+
GND
GND
GND
6.35mm Unbalanced Jack 3.5mm Stereo Jack
(HOT)LEFTRIGHT
3
Balanced XLR
1 GROUND
2 HOT
3 COLD
CONNECTOR WIRING

17
SPECIFICATIONS
(Stand
not included)
W
H
D
35mm pole Socket
Thumb screw
Media Player
Depth - D Width - W Height - H Weight
Unit 312 315 490 9.5 + 10.5
Packed 365 635 555 22
~10V-240V 50/60Hz
F3.15A L 250V
1x 10" (per Cabinet)
Level Control
300W (Maximum)
400W Total (2*200W)
1" Compression Driver (per Cabinet)
2 Unbalanced Line Level 6.35mm Jack
1 Stereo 3.5mm minijack
Left & right RCA connectors
3.5mm Headphone Output
Features:
Balanced XLR Mic (with global switchable Phantom Power)
20Hz - 20KHz
Balanced 2K2 Ohm
-33dBu (15mV)
Unbalanced 10K Ohm
0dBu (0.75V) Nominal
Operating voltage Range
Mains Fuse
Power Consumption
Amplifier Power
Woofer
Multi Input Stereo
Tweeter
Frequency Range
Mic Input
Mic Sensitivity
Line Input
Line Senditivity
4 Mono Inputs
Left & Right 6.35 JackMonitor Outputs
Master Outputs
Dimensions (mm) & (Kg)
Unbalanced Line Input 6.35mm Jack
Active EQ - Treble & Bass
Echo Level send control
Channel Level Control
Peak LED
Bluetooth A2DP
Micro SD Card
USB Host
Level Control
Left & right RCA connectors
Level Control
Left & Right 6.35 Jack
Master Volume
LED Level Meter
Master Echo Level

18
HINTS & TIPS
Unpacking
Inspect the product during unpacking, if any damage is found, notify the dealer you purchased it from immediately.
Be sure to save the carton and all packaging materials. Should you ever need to return the unit back to the dealer
or HH Electronics, use only the original factory packing.un all cables neatly, use cable ties to tidy excess cable length
in 'figure-8' not loops.
Basic Setup
HH Vector cabs can be mounted on the floor, or a suitable pole or tripod. Don't over-extend poles/tripods; ensure
at least 4 x the pole diameter is still inside the outer pole. Make sure the legs have a good splay on tripods, but do
not obstruct doorways or other access-ways.
If a pole mount is used, make sure that the thumb screw on the cabinet is tight.
Switching Off
After using the amplifier, please adjust the gain controls to their lowest settings, then the amplifier can be turned off
safely. Turn the power switch to the OFF position and remove the power cord from the electrical source.
NOTE:
Do not connect or disconnect from the input signal source when the amplifier is turned ON, damage could occur
to the amplifier and the speaker.
If the amplifier is in standby mode without use for over 3 hours, remove the power cord from the electrical source.
QUICK TIPS
ŸUse electronic safety devices such as circuit breakers.
ŸStart with EQ settings flat and gains low.
ŸMaster volumes should be at zero for switch on and off.
ŸUse the minimum cut or boost in EQ. If all bands are boosted or cut, flatten EQ, re-adjust gain and start again.
ŸUse input gain to set maximum signal level without distortion (use VU meters, bar graphs or peak lights). Amps
should have peak or clip lights illuminating only on signal peaks, not all the time.
ŸSet up mic levels first, and adjust other equipment to match.
ŸAvoid very high onstage levels from backline amps.
ŸWhen using separate power amps, turn the level of the amp to maximum. Control overall level from your mixer,
not the power amp.
ŸAvoid damp environments and extremes of temperature for storage and use of all audio equipment.
ŸLook after your cables. Do not stand equipment on, or run cases over them, do not tie knots in them and
always use them for the correct application (a signal lead is NOT a speaker lead). Coil and secure with cable
ties before storing.
ŸEnsure your equipment is properly loaded and cannot move around during transit.
ŸKeep lights away from speakers; heat can cause fires/speaker damage.
ŸDon't run cables across access-ways; if you have to, run them above doors or use approved cable covers.
ŸBe aware of total power usage. Overloading a mains socket is potentially dangerous, and likely to cause a power
out during use.
ŸKeep lighting cables away from ALL sound cables including mains, use separate circuit for lights if possible.
ŸKeep power and signal cables apart.

19
LEGAL
FCC COMPLIANCY STATEMENT
This device complies with Part 15 of the FCC rules.
Operation is subject to the following two conditions:
1) This device may not cause harmful interference
2) This device must accept any interference received, that may cause undesired
operation.
Warning: Changes or modification to the equipment not approved by Laney can void the user's
authority to use the equipment.
!Note: This equipment has been tested and found to comply with the limits for Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try and correct the
interference by one or more of the following measures.
!Reorient or relocate the receiving antenna.
!Increase the separation between the equipment and receiver.
!Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
!Consult the dealer or an experienced radio/TV technician for help
--------------------------------------------------------------------------------
This product conforms to the requirements of the following European Regulations, Directives &
Rules:
CE Mark (93/68/EEC), Low Voltage 2006/95/EC, EMC (2004/108/EEC), RoHS (2011/65/EU),
RED (2014/30/EU), ErP 2009/125/EU
---------------------------------------------------------------------------------
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, HH Electronics Ltd. declares that the radio equipment type S2-210 is in compliance with
Directives 2014/53/EU, 2011/65/EU, 2009/125/EU
Full text of the EU declaration of conformity is available at the following internet address:
support.hhelectronics.com/approvals
---------------------------------------------------------------------------------
In order to reduce environmental damage, at the end of its useful life, this product must not be
disposed of along with normal household waste to landfill sites. It must be taken to an approved
recycling centre according to the recommendations of the WEEE (Waste Electrical and Electronic
Equipment) directive applicable in your country.
---------------------------------------------------------------------------------
Bluetooth® and the Bluetooth logo are registered trademarks of Bluetooth SIG. All other product
or company names are trademarks or registered trademarks of their respective owners.
INCORPORATED RADIO EQUIPMENT DEVICE TECHNICAL SPECIFICATION:
Frequency Range:
Transmit Power:
Receiver Sensitivity:
Operating Protocol:
2402-2480MHz
+8dBm (6.3mW)
-91dBm
Bluetooth Class 2
In the interest of continued development, HH Electronics Ltd.
reserves the right to amend product specification without prior notification.