Hi TV Ture TV User manual

MOBILE DIGITAL TV RECEIVER
Ture TV
Ture TV
USER MANUAL

TABLE OF CONTENTS
Remote Control 2
Product Exterior 3
Front Panel 3
Rear Panel 4
Installation Diagram 5
Front Installation Diagram 5
Rear Installation Diagram 6
Operating Guide 7
Control Panlel Usage 7
Channel Function Menu 8
Settings and Machine Setup9
Search Function Menu 14
15
16
17
Specifcations 18
EPG Setting
Muli-Audio Selection
Special Attention Items
NOTE 19

Digital Set-top Box Special Features
Suitable for areas with DVB-T reception.
Receives both UHF and VHF signals. antenna installation
is easier than traditional type.
Built-in digital decoder and receiver , therefore the
images won't be snowy, ghosty, or lose fidelity and
colour.
Digital decoder automatically corrects for distorted signal ,
so as to increase the Signal-to-Noise (S/N) Ratio and
reception capability.
Provides different image ratios of either 4:3 and 16:9,
which the user can select at will.
Can receive SDTV (Standard Digital Television) pro-
grams, so the images are clearer and more natural, and
the colours richer.
Suitable for normal TV sets, the video outputs can be
connected to traditional CRT (Cathode Ray Tube), LCD
(Liquid Crystal Displays), or PDP (Plasma Display
Panel) displays.
Provides the Electronic Program Guide (EPG) function,
which provides program previews.
High fidelity sound; stereo sound output; digital 24-bit
processing; therefore the sound quality is as good as
music CD.
High fidelity images; no loss in fidelity; therefore the
images are as good as DVD quality.
Multi-language control menu.

SAFETY GUIDELINES
In order to ensure vehicle safety, the driver side screen must
be connected to the "4Video Out" connector. This will
ensure the driver won't be able to watch TV while the vehicle
is moving. The driver will be able to watch TV once the hand-
brake is activated. The rear passenger screens are connect-
ed via the "1,2,3Video Out" and are not under the same
restriction.
WARNING
To avoid electrical shock or bodily harm, please ensure the
following:
œPlease do not use the receiver if it is defective.
œPlease do not use the receiver in an environment with
mist, dust, and fuel vapours.
œPlease do not provide the receiver with voltage exceed-
ing the marked range.
EMERGENCY HANDLING
If the machine is exhibiting unusual behaviour, please turn off
its power quickly and contact our service centre for support.
Please do not attempt to repair the machine yourself, so as to
prevent any danger.
1

2
REMOTE CONTROL

3
PRODUCT OVERVIEW
Front Panel
2
1
2
3
4
5
6
7
* M od e : 4 different modes. Each mode has different function.
1 2
O N O N Viewing mode
O N O FF Erase EEPRO M mode (for EEPRO M erasing)
O FF O N Loader mode (for software upgrade)
O FF O FF C hange video output mode (for PAL/ N TSC / SEC AM mode switching)
P r o ce d u r e s :
a. If O SD in video is in PAL mode
b. set switch to O FF/ O FF
c. Reset or cycle the power
d. O SD in video is in N TSC mode
e. For changing N TSC to SEC AM or
SEC AM to PAL mode, just do the
same procedures.
VIDEO OUT
Video output to external device such as
LCD panel
AUDIO OUT L/R
Audio output to external device such
as LCD panel
IR IN
Infra-ray external cable connector
Conect to pc for updation software
POWER LED
The green light is lit in power on mode
MODE
Viewing mode (On/On), Erase
EEPROM (On/Off), software update
(Off/On), PAL/NTSC/SECAM mode switch
DC IN/SC/ANT-POWER
DC 12V~24V power input, ACC,
handbrake control, power antenna, ground
UPGRADE
12347
56

4
Rear Panel
1
1 ANTENNA IN
Connect to terrestrial TV aerial

2A FUSE
LCD
5
INSTALLATION
Front Installation Diagram
Ture TV
HI-FI AMPLIFIER
YELLOW
+12V~+24V
BLACK
GND
RED
ACC
BLUE
+5V OUTPUT
BLACK
GND
GREEN
HANDBRAKE CONTRO

6
Rear Installation Diagram

7
OPERATING GUIDE
Control Panel Usage
œPress the Menu button to display the
control panel.
œThe default menu displayed will be the
CHANNEL menu. (The text of the
selected menu will change its colour
from white to yellow).
œUse the CHANNEL menu to preview
the program parameters, to display the
signal status, and to set up a password
lock.
œWhile in the control panel, press the
Menu button and then the Setup but-
ton to select the SETTING menu. Enter
the sub-menu.
œUse the SETTING menu to customize
the basic functionalities of the set-up
box according to the user's prefer-
ences.
œWhile in the control panel, press the
Menu button and then the SEARCH
button to select the SEARCH menu.
œUse the SEARCH menu to select the
scan method and display the signal sta-
tus.

8
œPress the Menu button to display the
control panel. The default menu dis-
played will be the CHANNEL menu.
œThe small screen on the left shows the
program being broadcasted on the
channel that is currently selected in the
list below.
œUse the ŕŞbuttons to preview other
channels.
œThe small screen to the right displays
the program parameters, the signal
strength and quality.
œSignal strength and quality display bar:
The larger the number and the longer
the bar the better the signal
œAt the bottom of the menu display is the
channel.
œUse the ŕŞbuttons to select a chan-
nel.
œUse the buttons to setup or can-
cel locking for the channel.
œEnter a user-selected 4-digit password
to setup or cancel the lock.
Channel Function Menu
ŕ
ŕ

9
Controlling the menu:
œPress the Menu button to display the
control panel.
œWhile in the control panel, press the
Menu button function menu and then
the Setup button.
œUse the ŕŞbuttons to select a menu
option (on the left).
œPress OK to enter the sub-menu (on
the right).
œUse the ŕŞbuttons to select an
option. Once selected, press OK to
confirm.
œPress EXIT to leave the menu.
Menu Language
œSelect this menu option to change the
language displayed in the control
panel.
Preferred Language
œSelect this menu option to change the
subtitle language.
Settings and Machine Setup

10
Change Password
œTo change the password for the chan-
nel lock, enter first the old 4-digit pass-
word, then the new 4-digit password,
and lastly the new password again as
confirmation.
œThe factory default for the old password
is 0000.
Aspect Ratio
œUse this menu option to select the
aspect ratio that is most suitable for the
TV screen.
Local Time
œIf the TV program being broadcasted
provides time information in GMT
(Greenwich Mean Time), then a local
GMT offset must be provided. For
example, the GMT offset for Sydney is
+10 hours.

11
Menu Transparency
œUse this menu option to change the
transparency of the subtitle.
œThe greater the number selected, the
more transparent it is.
Banner Time
œUse this menu option to change the
amount of time the banner stays visible
when no commands are issued.
œThe greater the number selected, the
longer the subtitle remains.
Factory Default
œUse this menu option to restore the fac-
tory default settings. All changes made
prior would be lost.

12
Controlling the menu:
œPress the Menu button to display the
control panel.
œWhile in the control panel, press the
Menu button function menu and then
the Setup button.
œUse the buttons to select a scan
method.
œPress OK to enter the Country menu
option.
œUse the buttons to select a country.
œPress OK to confirm.
œUse the ŕŞbuttons to select the
options inside the carrier window.
œPress OK to confirm.
œPress EXIT to leave the menu.
Add a New Carrier
œFrom Scan Mode select Add Carrier.
œSelect your country from Country.
œOnce the new carrier has been select-
ed in the carrier window, press OK to
start the scan.
œIf signal was received during the scan,
the statistics window will show details
about the carrier, the signal strength
and quality.
œAfter the scan, the carrier window will
show a green light to indicate that carri-
er is in service. A red light means that
the carrier is not in service.
ŕ
ŕ
ŕ
ŕ

13
Delete a Carrier
œFrom Scan Mode select Delete Carrier.
œSelect your country from Country.
œSelect a carrier from the carrier window
and press OK to delete.

14
Search Function Menu
Auto Scan
Fast
œFrom Scan Mode select Fast.
œOnce your country has been selected,
press OK to run the scan (the scan is
performed quickly).
Complete
œFrom Scan Mode select Complete.
œOnce your country has been selected,
press OK to run the scan (the scan will
run for a longer period of time).
Edit a Carrier
œFrom Scan Mode select Edit Carrier.
œSelect your country from Country.
œSelect a carrier from the carrier window
and press OK to edit.