Hidrotermal UV-Y80W(2U/40W) User manual

UV-Y Disinfection Systems
Swimming UV-Y Sterilizer
USER MANUAL

Y Series UV Sterilizer Specifications
Y Series UV Sterilizer
No. Model
Flow rate
(30mj/cm2 )Lamp
watts
Qty.
Lamps
Total
Power Inlet/Outlet
Reactor Size
(mm)
GPM m3/Hr L W H
1 UV-Y80W(2U/40W) 44 10 40W 2 80W Ф63mm(2") 300 445 1103
2 UV-Y120W(3U/40W) 66 15 40W 3 120W Ф63mm(2") 300 445 1103
3 UV-Y160W(4U/40W) 88 20 40W 4 160W Ф75mm(2.5") 350 458 1162
4 UV-Y200W(5U/40W) 110 25 40W 5 200W Ф110mm(4") 400 548 1180
5 UV-Y240W(6U/40W) 132 30 40W 6 240W Ф110mm(4") 400 548 1180
6 UV-Y160W(2U/80W) 88 20 80W 2 160W Ф75mm(2.5") 300 445 1103
7 UV-Y240W(3U/80W) 132 30 80W 3 240W Ф90mm(3") 300 445 1103
8 UV-Y320W(4U/80W) 176 40 80W 4 320W Ф110mm(4") 350 491 1162
9 UV-Y400W(5U/80W) 220 50 80W 5 400W Ф110mm(4") 400 548 1180
10 UV-Y480W(6U/80W) 264 60 80W 6 480W Ф110mm(4") 400 548 1180
Specifications subject to change without notice, since our company reserves the change right.
Inlet
Outlet

1. Installation
1.1 Feature
1．Water cooling for ballasts installed inside the cover hat of chamber.
2．Water right rate: IP56
3．Outdoor and indoor installation available
4．Start up and off according the signal from flow switch.
5. Easily installation and simple maintenance.
1.2 Installation of UV sterilizer
The UV sterilizer should be placed Vertically. Filtration should be applied before the UV Sterilizer
system to provide high quality pretreated water for UV disinfection. Procedure for UV Sterilizer
installation is as follow:
(1) Unloose and take off the nut(s) on the end(s) of chamber.
(2) Insert the quartz sleeve into the chamber carefully, then cover the O-ring on the end of the quartz
sleeve.
(3) Screw the nut on the end of chamber and tighten it. Note: Do not use force implement to avoid
breaking up the quartz sleeve.
(4) Check all the junctions and open the tap to see if leaks happen.
(5) Please install water flow controller before UV sterilizer if the water flow is too fast.
(6) Once it is determined that there are no leaks, connect the lamp with ballast , then insert into quartz
sleeve. Screw the waterproof connector into the nut, and tighten it.
(7) Open the water valve first, then power on the unit..
(8) Power on and to check whether the lamp works well or not. Warning: Do never look at the UV
Lamps with naked eyes when the UV lamp is power on.
1.3 Operation
1．Open the Inlet and Outlet valve.
2．Plug the power, and the unit will be powered on automatically.
When the water level can not reach the set level, the alarm will be triggered.
3．When the ballast and lamp fail, the alarm will be triggered.
4．Power off the unit, closed the Inlet and Outlet valve, then unplug the power.

2. Instructions of Operating & Maintenance
2.1 Caution: Be sure to unplug the unit before performing any work on the
sterilizer
1. Regularly inspect your sterilizer unit to ensure that the UV lamp working properly. If the UV lamp
fails, the audio and visual alarm will be triggered.
2．Screw out the waterproof connector , and take out the fault lamp. Re-install a new UV lamp into
the quartz sleeve and connect the wire. Screw the waterproof connector into the nut . You should pay
attention that no water leaks at the all junctions. Then power on the unit to see if it works.
3．Replace the UV lamp after one year of continual working time (9000 hours), to ensure high
disinfection effect. Do not turn on and off the UV lamp frequently, it will reduce the lamp’s effective
life.
4．Never touch the place where there is UV radiation.
3. Quality Warranty
1. Not responsible for any incidental or consequential damages of misuse.
2. One year guarantee for unit quality.