HIK VISION DS-2AE7232TI-A User manual

HD-TVI Speed Dome
Quick Start Guide
UD02198B

HD-TVI Speed Dome·Quick Start Guide
i
Quick Start Guide
COPYRIGHT © 2016 Hangzhou Hikvision Digital Technology Co., Ltd.
ALL RIGHTS RESERVED.
Any and all information, including, among others, wordings, pictures, graphs are the properties of
Hangzhou Hikvision Digital Technology Co., Ltd. or its subsidiaries (hereinafter referred to be
“Hikvision”). This user manual (hereinafter referred to be “the Manual”) cannot be reproduced,
changed, translated, or distributed, partially or wholly, by any means, without the prior written
permission of Hikvision. Unless otherwise stipulated, Hikvision does not make any warranties,
guarantees or representations, express or implied, regarding to the Manual.
About this Manual
This Manual is applicable to HD-TVI Speed Domes.
The Manual includes instructions for using and managing the product. Pictures, charts, images and
all other information hereinafter are for description and explanation only. The information
contained in the Manual is subject to change, without notice, due to firmware updates or other
reasons. Please find the latest version in the company website (http://overseas.hikvision.com/en/).
Please use this user manual under the guidance of professionals.
Trademarks Acknowledgement
and other Hikvision’s trademarks and logos are the properties of Hikvision in various
jurisdictions. Other trademarks and logos mentioned below are the properties of their respective
owners.
Legal Disclaimer
TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH ITS
HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,
AND HIKVISION MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND
NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL HIKVISION, ITS DIRECTORS, OFFICERS,
EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR
INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS,
BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH THE
USE OF THIS PRODUCT, EVEN IF HIKVISION HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH
DAMAGES.
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY
AT YOUR OWN RISKS. HIKVISION SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL
OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER
ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, HIKVISION WILL
PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR
JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS
THE APPLICABLE LAW. HIKVISION SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED
WITH ILLEGITIMATE PURPOSES.

HD-TVI Speed Dome·Quick Start Guide
ii
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER
PREVAILS.
03261060707

HD-TVI Speed Dome·Quick Start Guide
iii
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits for a digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause
undesired operation
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked with "CE"
and comply therefore with the applicable harmonized European standards listed
under the Low Voltage Directive 2006/95/EC, the EMC Directive 2004/108/EC, the
RoHS Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed
of as unsorted municipal waste in the European Union. For proper recycling, return
this product to your local supplier upon the purchase of equivalent new equipment, or
dispose of it at designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot be
disposed of as unsorted municipal waste in the European Union. See the product
documentation for specific battery information. The battery is marked with this
symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to your supplier or to a designated
collection point. For more information see: www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

HD-TVI Speed Dome·Quick Start Guide
iv
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger
or property loss.
The precaution measure is divided into “Warnings” and “Cautions”
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
Warnings
All the electronic operation should be strictly compliance with the electrical safety regulations,
fire prevention regulations and other related regulations in your local region.
Please use the power adapter, which is provided by normal company. The standard of the power
adapter is 24VAC10% or 12VDC10% (depending on models). The power consumption cannot
be less than the required value.
Do not connect several devices to one power adapter as adapter overload may cause over-heat
or fire hazard.
Please make sure that the power has been disconnected before you wire, install or dismantle the
speed dome.
When the product is installed on wall or ceiling, the device shall be firmly fixed.
If smoke, odors or noise rise from the device, turn off the power at once and unplug the power
cable, and then please contact the service center.
If the product does not work properly, please contact your dealer or the nearest service center.
Never attempt to disassemble the speed dome yourself. (We shall not assume any responsibility
for problems caused by unauthorized repair or maintenance.)
Cautions
Do not drop the dome or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or places
subject to shock (ignorance can cause equipment damage).
Do not place the dome in extremely hot, cold, dusty or damp locations, otherwise fire or
electrical shock will occur. The operating temperature should be -30°C ~ 65°C (outdoor speed
dome) and -10°C ~ 50°C (indoor speed dome).
The dome cover for indoor use shall be kept from rain and moisture.
Exposing the equipment to direct sun light, low ventilation or heat source such as heater or
radiator is forbidden (ignorance can cause fire danger).
Warnings Follow
these safeguards to
prevent serious injury
or death.
Cautions Follow these
precautions to prevent
potential injury or material
damage.

HD-TVI Speed Dome·Quick Start Guide
v
Do not aim the speed dome at the sun or extra bright places. A blooming or smear may occur
otherwise (which is not a malfunction however), and affecting the endurance of sensor at the
same time.
Please use the provided glove when open up the dome cover, avoid direct contact with the dome
cover, because the acidic sweat of the fingers may erode the surface coating of the dome cover.
Please use a soft and dry cloth when clean inside and outside surfaces of the dome cover, do not
use alkaline detergents.
Please keep all wrappers after unpack them for future use. In case of any failure occurred, you
need to return the speed dome to the factory with the original wrapper.Transportation without
the original wrapper may result in damage on the speed dome and lead to additional costs.

HD-TVI Speed Dome·Quick Start Guide
vi
Table of Contents
1 Installation ........................................................................................................ 1
1.1 Connecting the Cables.............................................................................................................. 1
1.2 DIP Switch Settings ................................................................................................................... 2
1.2.1 5-inch Speed Dome Settings.............................................................................................. 2
1.2.2 5-inch IR & Mini IR Speed Dome Settings .......................................................................... 4
1.2.3 7-inch IR Speed Dome Settings.......................................................................................... 7
1.2.4 Mini Speed Dome Settings ................................................................................................ 9
1.3 Wiring and Installation ........................................................................................................... 11
1.3.1 Wiring.............................................................................................................................. 11
1.3.2 Installing the Bracket ....................................................................................................... 12
1.3.3 Setting the DIP Switch ..................................................................................................... 13
1.3.4 Installing the Speed Dome............................................................................................... 13
2 In-door Mounting Applications....................................................................... 14
2.1 5-inch Speed Dome In-ceiling Mounting Applications ............................................................ 14
2.2 5-inch Speed Dome Ceiling Mounting Applications................................................................ 16
2.2.1 Removing the Mounting Bracket ..................................................................................... 16
2.2.2 Wiring.............................................................................................................................. 17
2.2.3 Ceiling Mounting ............................................................................................................. 18
2.3 Mini Speed Dome In-ceiling Mounting Applications............................................................... 20
2.4 Mini Speed Dome Ceiling Mounting Applications .................................................................. 22
2.4.1 Wiring.............................................................................................................................. 22
2.4.2 Ceiling Mounting ............................................................................................................. 22
3 Application and Operations ............................................................................ 24
3.1 System Application ................................................................................................................. 24
3.2 Basic Operations..................................................................................................................... 24
3.2.1 Configuring Patrol............................................................................................................ 25
3.2.2 Configuring Park Actions ................................................................................................. 28
4 Troubleshooting.............................................................................................. 30
4.1 Device Exceptions................................................................................................................... 30
4.2 PTZ Control Exceptions........................................................................................................... 30
4.3 Other Questions ..................................................................................................................... 30

HD-TVI Speed Dome·Quick Start Guide
1
1Installation
Before you start:
Check the package contents and make sure that the device in the package is in good condition and
all the assembly parts are included.
There are several ways to install the analog speed dome. The wall mounting is taken as an example
below.
1.1 Connecting the Cables
Please turn the power off before connecting the cables.
The cable interfaces of speed dome are shown in following figure. The cables are distinguished by
different colors. The labels attached on the cables are for identification.
The cables may vary according to different camera models. Please refer to the actual device.
REDAC24V
YELLOW/GREEN
BLACKAC24V
YELLOWR485-
ORANGER485+
VI EOD
Alarm
HD-TVI Video Output
Power Supply
VI E OD
CVBS Video Output
RS485
Figure 1-1 Cables
Table 1-1 Cables Description
Name
Description
Power Supply
AC24V/DC12V
HD-TVI Video Output
HD-TVI and coaxial video output
CVBS Video Output
SD analog video output
RS485
485 control
Alarm
Alarm input and alarm output

HD-TVI Speed Dome·Quick Start Guide
2
1.2 DIP Switch Settings
1.2.1 5-inch Speed Dome Settings
The DIP switch is used for setting the address and baudrate for the speed dome, with value ON=1
and OFF=0.
The SW1 switches from the first to the eighth are used to set the address. The SW2 switches are
used to set the baudrate.
The default dome address is 0. The default baudrate is 2400.
123456781
2
DIP Switch
Figure 1-2 DIP Switch Settings for 5-inch Outdoor Speed Dome
1 2 3 4 5 6 7
8
1 2
DIP Switch
Figure 1-3 DIP Switch Settings for 5-inch Indoor Speed Dome
Figure 1-4 Enlarged View of DIP Switch
Address Settings
The SW1 switches from 1 to 5 are used for setting the address of speed dome. You can refer to
Table 1-2 for details of setting the speed dome address to a specific number.
Table 1-2 Set the Dome Address

HD-TVI Speed Dome·Quick Start Guide
3
Switch No.
Dome Address
1
2
3
4
5
0
OFF
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
…
…
…
…
…
…
31
ON
ON
ON
ON
ON
Protocol Settings
The number 6 and 7 of SW1 switches are for setting the protocol of the speed dome. You can refer
to Table 1-3 for details of setting the speed dome protocol.
Table 1-3 Set the Protocol of the Dome
Switch No.
Protocol
6
7
Self-adaptive
OFF
OFF
PELCO_D
ON
OFF
MAN_BOSCH
OFF
ON
MAN_AD
ON
ON
TVI Mode Settings
The number 8 of SW1 switches is for setting the TVI mode of the speed dome. You can refer to
Table 1-4 for details of TVI mode settings.
Table 1-4 Set the TVI Mode
Switch No.
TVI Mode
8
V2.0
OFF
V1.0
ON
Baudrate Settings
The number 1 and 2 SW2 switches are used for setting the baudrate of the speed dome. The
baudrate can be 2400bps, 4800bps, 9600bps and 19200bps. The baudrate will be set as 2400bps by
default if it is out of this range. Refer to the following table:

HD-TVI Speed Dome·Quick Start Guide
4
Table 1-5 Set the Baudrate of the Dome
Switch No.
Baudrate
1
2
2400
OFF
OFF
4800
ON
OFF
9600
OFF
ON
19200
ON
ON
1.2.2 5-inch IR & Mini IR Speed Dome Settings
The DIP switch is for setting the speed dome address, baudrate, protocol, etc., with value ON=1 and
OFF=0. The switch label of the 5-inch IR speed dome is on the back of the SWITCH cover as shown
in Figure 1-5. The DIP switch of mini IR speed dome is shown in Figure 1-6.
DIP Switch
Screws
Switch Cover
Figure 1-5 Position of DIP Switch for 5-inch IR Speed Dome
DIP Switch Location of Mini IR Speed Dome
Screws DIP Switch
Figure 1-6 DIP Switch of Mini IR Speed Dome
Setting DIP Switch

HD-TVI Speed Dome·Quick Start Guide
5
1 75 6432 8 9 10
ON DIP
1 2
ON
Figure 1-7 Enlarged View of DIP Switch
For some certain models, the two individual DIP switches at the left side of the Figure 1-7 are
supported for turning on/off the terminator; while other models are not supported.
The default dome address is 0; the default baudrate is 2400; and the default value of the 120Ω
terminator is OFF.
Table 1-6 Switch Functions
Switch
Function
1 to 5
Set the address for the speed dome
6, 7
Set the baudrate for the speed dome
8
Set the protocol for the speed dome
9
Set the TVI mode for the speed dome
10
Set the terminal resistor for the speed dome
The DIP switch is designed according to binary system. When the switch is ON, it stands for the
number 1. When the switch is OFF, it stands for the number 0.
Example:
The switches from No. 1 to 5 are used to set the speed dome address. No. 1 is the lowest digit and
No. 5 is the highest. Turning on all these 5 switches stands for the binary number 11111. Converting
the 11111 to a decimal number is 31. So the speed dome address will be 31.
Address List
For convenient settings, refer to the following list to set the address for the speed domes.
Table 1-7 Dome Address
Switch No.
Dome Address
1
2
3
4
5
0
OFF
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
…
…
…
…
…
…
31
ON
ON
ON
ON
ON

HD-TVI Speed Dome·Quick Start Guide
6
Baudrate List
For convenient settings, refer to the following list to set the baudrate for the speed dome. The
baudrate will be set as 2400bps by default if it is out of this range.
Table 1-8 Baudrate
Switch
Baudrate
6
7
2400
OFF
OFF
4800
ON
OFF
9600
OFF
ON
19200
ON
ON
Protocol List
For convenient settings, refer to the following list to set the protocol for the speed dome.
Table 1-9 Protocol
Protocol
8
Self-adaptive
OFF
MAN_AD
ON
TVI Mode
Table 1-10 TVI Mode
TVI Mode
9
V2.0
OFF
V1.0
ON
The speed dome is self-adaptive to private protocol when the No.8 and 9 switches are both
OFF.
Terminal Resistor
Table 1-11 Terminal Resistor
Terminal Matching Resistance
10
Turn on the Resistor
ON
Turn off the Resistor
OFF

HD-TVI Speed Dome·Quick Start Guide
7
1.2.3 7-inch IR Speed Dome Settings
Two DIP switches SW1 and SW2 are for setting the speed dome address, baudrate, protocol, etc.,
with value ON=1 and OFF=0. The switch label is on the back of the SWITCH cover as shown in Figure
1-8.
Each number of the switch represents a DIP value, ranging from 1 to 8 for the lowest to highest.
SW1 SW2
Figure 1-8 Label of DIP Switch for IR Speed Dome
ON
12345678
SW2
ON
12345678
SW1
Figure 1-9 Enlarged View of DIP Switch
The default dome address is 0; the default baudrate is 2400; and the default value of the 120Ω
terminator is OFF.
Address Settings
The SW1 switches are used for setting the address of speed dome. You can refer to Table 1-12 for
details of setting the speed dome address to a specific number.
Table 1-12 Set the Dome Address
Dome Address
1
2
3
4
5
6
7
8
0
OFF
OFF
OFF
OFF
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
OFF
OFF
OFF
...
...
...
...
...
...
...
...
...
255
ON
ON
ON
ON
ON
ON
ON
ON

HD-TVI Speed Dome·Quick Start Guide
8
Baudrate Settings
The No. 1, 2 of SW2 switches are for setting the baudrate of the speed dome, standing for 2400bps,
4800bps, 9600bps and 19200bps respectively. The baudrate will be set as 2400bps by default if it is
out of this range. Refer to the following table:
Table 1-13 Set the Baudrate of the Dome
DIP Switch SW2-Baudrate Settings
Baudrate
1
2
2400
ON
OFF
4800
OFF
ON
9600
ON
ON
19200
OFF
OFF
Protocol Settings
For convenient settings, refer to the following list to set the protocol for the speed dome.
Table 1-14 Set the Protocol of the Dome
DIP Switch SW2-Protocol Settings
Protocol
3
4
5
Self-adaptive
OFF
OFF
OFF
PELCO_P
ON
OFF
OFF
PELCO_D
OFF
ON
OFF
HIKVISION
ON
ON
OFF
KALATE
OFF
OFF
ON
VICON
ON
OFF
ON
MAN_BOSCH
OFF
ON
ON
MAN_AD
ON
ON
ON
TVI Mode Settings
The No. 7 of SW2 switches is for setting the TVI mode of the speed dome. You can refer to the
following table for details of setting the speed dome TVI mode.
Table 1-15 Set the TVI Mode
TVI Mode
7
V2.0
OFF
V1.0
ON

HD-TVI Speed Dome·Quick Start Guide
9
Terminal Resistor Settings
The No. 8 of SW2 switches is used for turning on/off the 120Ωterminal resistor.
Table 1-16 Set Terminal Resistor
Terminal Matching Resistance
8
Turn on the Resistor
ON
Turn off the Resistor
OFF
The o-ring in the groove of the switch cover is for waterproof.
1.2.4 Mini Speed Dome Settings
DIP Switch Location of Mini Analog Speed Dome
DIP Switch
Figure 1-10 DIP Switch of Mini Analog Speed Dome
Setting DIP Switch
1 75 6432 8 9 10
ON DIP
1 2
ON
Figure 1-11 Enlarged View of DIP Switch
Table 1-17 Switch Functions
Switch No.
Function
1 to 5 (SW1)
Set the address for the speed dome
6, 7 (SW1)
Set the baudrate for the speed dome
8, 9 (SW1)
Set the protocol for the speed dome
10 (SW1)
Set the TVI mode for the speed dome
1, 2 (SW2)
Set the terminal resistor for the speed dome

HD-TVI Speed Dome·Quick Start Guide
10
The DIP switch is designed according to binary system. When the switch is ON, it stands for the
number 1. When the switch is OFF, it stands for the number 0.
Example:
The SW1 switches from No. 1 to 5 are used to set the speed dome address. No. 1 is the lowest digit
and No. 5 is the highest. Turning on all these 5 switches stands for the binary number 11111.
Converting the 11111 to a decimal number is 31. So the speed dome address will be 31.
Address List
For convenient settings, refer to the following list to set the address for the speed domes.
Table 1-18 Dome Address
Switch No.
Dome Address
1
2
3
4
5
0
OFF
OFF
OFF
OFF
OFF
1
ON
OFF
OFF
OFF
OFF
2
OFF
ON
OFF
OFF
OFF
3
ON
ON
OFF
OFF
OFF
…
…
…
…
…
…
31
ON
ON
ON
ON
ON
Baudrate List
For convenient settings, refer to the following list to set the baudrate for the speed dome. The
baudrate will be set as 2400bps by default if it is out of this range.
Table 1-19 Baudrate
Switch No.
Baudrate
6
7
2400
OFF
OFF
4800
ON
OFF
9600
OFF
ON
19200
ON
ON
Protocol List
For convenient settings, refer to the following list to set the protocol for the speed dome.

HD-TVI Speed Dome·Quick Start Guide
11
Table 1-20 Protocol
Switch No.
Protocol
8
9
Self-adaptive
OFF
OFF
Pelco_P
ON
OFF
The speed dome is self-adaptive to private protocol when the No.8 and 9 switches are both
OFF.
TVI Mode
For convenient settings, refer to the following list to set the TVI mode of the speed dome.
Table 1-21 TVI Mode
Switch No.
TVI Mode
10
V2.0
OFF
V1.0
ON
Terminal Resistor
The No. 1 and No.2 of SW2 switches are used for turning on/off the 120Ωterminal resistor.
Table 1-22 Terminal Resistor
Switch No.
1
2
Turn on the Resistor
ON
ON
Turn off the Resistor
OFF
OFF
1.3 Wiring and Installation
There are several ways to install the speed dome. The wall mounting is taken as an example below.
1.3.1 Wiring
The survey of the actual installation environment and planning the wiring is highly recommended
before the accurate deployment of the wire is implemented in order to provide a safe and steady
power supply and a reasonable wiring route.
Get familiar with the installation environment before deploying the wire, including the wiring
distance, surrounding, and electromagnetic interference and so on.
Please choose the cable with nominal voltage higher than the actual voltage, to ensure a
normal running in case of unsteady voltage.

HD-TVI Speed Dome·Quick Start Guide
12
To protect the power cable and the signal transmitting cable from human tampering, you
should pay attention to the protection and reinforcement of the cables.
When deploying the wire, please do not tighten the wire or make the wire loose.
The wiring of the speed dome should be performed by professionals.
1.3.2 Installing the Bracket
Before you start:
Wall mounting is applicable to the indoor/outdoor solid wall construction. The followings are the
mandatory precondition for wall mounting:
The wall must be thick enough to install the expansion screws.
Please make sure that the wall is strong enough to withstand more than 8 times the weight of
the dome and the mount.
Steps:
1. Check whether the type of the bracket and the number of accessories are right, as shown in
the figure below.
Figure 1-12 Wall Mount Bracket, Nuts and Flat Washers
2. Drill 4 screw holes in the wall according to the holes of the mount, and then insert M8
expansion screws (not supplied) into the mounting holes.
Figure 1-13 Drill Mounting Holes
3. Attach the wall mount to the wall by aligning the 4 screw holes of the mount with expansion
screws on the wall.
4. Secure the wall mount with 4 hex nuts and washers.

HD-TVI Speed Dome·Quick Start Guide
13
Figure 1-14 Secure the Mount
5. Install the speed dome to the mount. Please refer to Section 1.3.4 Installing the Speed Dome
for installation details.
Follow the same instructions described above for the short-arm wall mounting. For outdoor
applications, please adopt the water-proof measures. The short-arm wall mount is not
recommended for outdoor applications.
1.3.3 Setting the DIP Switch
Set the address and baudrate for the speed dome. The default value of DIP switch is shown below:
Address: 0
Baudrate:2400
Terminal Resistor: OFF
Please refer to the Section 1.2 DIP Switch Settings for DIP switch settings.
1.3.4 Installing the Speed Dome
The sketches of installing the speed dome are for reference only.
Steps:
1. Hang the safety rope to the speed dome and then hook to the mount as shown in Figure
1-15(left).
2. Route the cables of the speed dome through the wall mount.
3. Connect the corresponding video/power/RS-485 cables.
4. Install the speed dome to the mount, and secure the speed dome by rotating the speed dome
clockwise.
5. Fasten the two lock screws with the Allen wrench, as shown in Figure 1-15(right).
③
②
①
Figure 1-15 Install the Speed Dome