HIK VISION DS-2CD6362F-I User manual

Network Fisheye Camera
User Manual
UD.6L0201D1624A01

User Manual of Network Fisheye Camera
1
Thank you for purchasing our product. If there are any questions or requests, please
do not hesitate to contact the dealer.
This manual applies to DS-2CD6362F-I (V) (S), DS-2CD6332FWD-I (V) (S)network
fisheye camera.
This manual may contain several technical incorrect places or printing errors, and the
content is subject to change without notice. The updates will be added to the new
version of this manual. We will readily improve or update the products or procedures
described in the manual.
DISCLAIMER STATEMENT
“Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability
of the security or signaling aspects of this product. UL has only tested for fire, shock
or casualty hazards as outlined in UL’s Standard(s) for Safety, UL60950-1. UL
Certification does not cover the performance or reliability of the security or signaling
aspects of this product. UL MAKES NO REPRESENTATIONS, WARRANTIES OR
CERTIFICATIONS WHATSOEVER REGARDING THE PERFORMANCE OR
RELIABILITY OF ANY SECURITY OR SIGNALING RELATED FUNCTIONS
OF THIS PRODUCT.”
0509001041027

User Manual of Network Fisheye Camera
2
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the
limits for a digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful
interference in which case the user will be required to correct the interference at his
own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the
following two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation.
EU Conformity Statement
This product and - if applicable - the supplied accessories too are
marked with "CE" and comply therefore with the applicable
harmonized European standards listed under the Low Voltage
Directive 2006/95/EC, the EMC Directive 2004/108/EC, the RoHS
Directive 2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol
cannot be disposed of as unsorted municipal waste in the European
Union. For proper recycling, return this product to your local
supplier upon the purchase of equivalent new equipment, or dispose
of it at designated collection points. For more information see:
www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that
cannot be disposed of as unsorted municipal waste in the European
Union. See the product documentation for specific battery
information. The battery is marked with this symbol, which may
include lettering to indicate cadmium (Cd), lead (Pb), or mercury
(Hg). For proper recycling, return the battery to your supplier or to
a designated collection point. For more information see:
www.recyclethis.info.

User Manual of Network Fisheye Camera
3
Safety Instruction
These instructions are intended to ensure that the user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into ‘Warnings’ and ‘Cautions’:
Warnings: Serious injury or death may be caused if any of these warnings are
neglected.
Cautions: Injury or equipment damage may be caused if any of these cautions are
neglected.
Warnings Follow these safeguards to
prevent serious injury or death.
Cautions Follow these precautions to
prevent potential injury or material
damage.
Warnings:
Please adopt the power adapter which can meet the safety extra low voltage
(SELV) standard. And source with 12 VDC or 24 VAC (depending on models)
according to the IEC60950-1 and Limited Power Source standard.
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the camera yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
To reduce the risk of fire or electrical shock, do not expose this product to rain or
moisture.
This installation should be made by a qualified service person and should conform
to all the local codes.
Please install blackouts equipment into the power supply circuit for convenient
supply interruption.
Please make sure that the ceiling can support more than 50(N) Newton gravities if
the camera is fixed to the ceiling.
If the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the camera yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)

User Manual of Network Fisheye Camera
4
Cautions:
Make sure the power supply voltage is correct before using the camera.
Do not drop the camera or subject it to physical shock.
Do not touch sensor modules with fingers. If cleaning is necessary, use a clean
cloth with a bit of ethanol and wipe it gently. If the camera will not be used for an
extended period of time, put on the lens cap to protect the sensor from dirt.
Do not aim the camera lens at the strong light such as sun or incandescent lamp.
The strong light can cause fatal damage to the camera.
The sensor may be burned out by a laser beam, so when any laser equipment is
being used, make sure that the surface of the sensor not be exposed to the laser
beam.
Do not place the camera in extremely hot, cold temperatures (the operating
temperature should be between -30°C ~ 60°C, or -40°C ~ 60°C if the camera
model has an “H” in its suffix), dusty or damp environment, and do not expose it
to high electromagnetic radiation.
To avoid heat accumulation, good ventilation is required for a proper operating
environment.
Keep the camera away from water and any liquid.
While shipping, the camera should be packed in its original packing.
Improper use or replacement of the battery may result in hazard of explosion.
Please use the manufacturer recommended battery type.
Notes:
For the camera supports IR, you are required to pay attention to the following
precautions to prevent IR reflection:
Dust or grease on the dome cover will cause IR reflection. Please do not remove
the dome cover film until the installation is finished. If there is dust or grease on
the dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol.
Make certain the installation location does not have reflective surfaces of objects
too close to the camera. The IR light from the camera may reflect back into the
lens causing reflection.
The foam ring around the lens must be seated flush against the inner surface of
the bubble to isolate the lens from the IR LEDS. Fasten the dome cover to camera
body so that the foam ring and the dome cover are attached seamlessly.

User Manual of Network Fisheye Camera
5
Table of Contents
Chapter 1 System Requirement................................................................................8
Chapter 2 Network Connection................................................................................9
2.1 Setting the Network Camera over the LAN......................................................... 9
2.1.1 Wiring over the LAN........................................................................................................9
2.1.2 Detecting and Changing the IPAddress .........................................................................10
2.2 Setting the Network Camera over the WAN.......................................................11
2.2.1 Static IP Connection .......................................................................................................11
2.2.2 Dynamic IP Connection..................................................................................................12
Chapter 3 Access to the Network Camera.............................................................15
3.1 Accessing by Web Browsers................................................................................ 15
3.2 Accessing by Client Software.............................................................................. 17
Chapter 4 Live View.................................................................................................18
4.1 Live View Page ..................................................................................................... 18
4.2 Starting Live View................................................................................................ 19
4.3 Recording and Capturing Pictures Manually ................................................... 20
4.4 Operating PTZ Control....................................................................................... 20
4.4.1 PTZ Control Panel..........................................................................................................20
4.4.2 Setting / Calling a Preset.................................................................................................21
4.4.3 Setting / Calling a Patrol.................................................................................................22
Chapter 5 Network Camera Configuration...........................................................24
5.1 Configuring Local Parameters............................................................................ 24
5.2 Configuring Time Settings .................................................................................. 26
5.3 Configuring Network Settings ............................................................................ 28
5.3.1 Configuring TCP/IP Settings..........................................................................................28
5.3.2 Configuring Port Settings ...............................................................................................29
5.3.3 Configuring PPPoE Settings...........................................................................................30
5.3.4 Configuring DDNS Settings...........................................................................................30
5.3.5 Configuring SNMP Settings ...........................................................................................34
5.3.6 Configuring 802.1X Settings..........................................................................................35
5.3.7 Configuring QoS Settings...............................................................................................36
5.3.8 Configuring UPnP™ Settings.........................................................................................37
5.3.9 Email Sending Triggered by Alarm ................................................................................38
5.3.10 Configuring NAT (Network Address Translation) Settings............................................40
5.3.11 Configuring FTP Settings...............................................................................................41
5.4 Configuring Video andAudio Settings............................................................... 42
5.4.1 Configuring Video Settings ............................................................................................42

User Manual of Network Fisheye Camera
6
5.4.2 Configuring Audio Settings............................................................................................44
5.4.3 Configuring ROI Encoding.............................................................................................45
5.5 Configuring Image Parameters .......................................................................... 47
5.5.1 Configuring Display Settings .........................................................................................47
5.5.2 Configuring OSD Settings..............................................................................................50
5.5.3 Configuring Privacy Mask..............................................................................................51
5.6 Configuring and Handling Alarms..................................................................... 52
5.6.1 Configuring Motion Detection........................................................................................52
5.6.2 Configuring Video Tampering Alarm .............................................................................55
5.6.3 Configuring Alarm Input ................................................................................................56
5.6.4 Configuring Alarm Output..............................................................................................57
5.6.5 Handling Exception ........................................................................................................58
5.6.6 Configuring Line Crossing Detection.............................................................................59
5.6.7 Configuring Intrusion Detection.....................................................................................60
5.7 Configuring Heat Map......................................................................................... 62
Chapter 6 Storage Settings......................................................................................65
6.1 Configuring NAS Settings................................................................................... 65
6.2 Configuring Recording Schedule........................................................................ 67
6.3 Configuring Snapshot Settings ........................................................................... 71
Chapter 7 Playback..................................................................................................73
Chapter 8 Log Searching.........................................................................................75
Chapter 9 Others......................................................................................................76
9.1 Managing UserAccounts..................................................................................... 76
9.2 Configuring RTSPAuthentication...................................................................... 78
9.3 Anonymous Visit .................................................................................................. 78
9.4 IPAddress Filter................................................................................................... 79
9.5 Security Service.................................................................................................... 81
9.6 Viewing Device Information................................................................................ 81
9.7 Maintenance ......................................................................................................... 82
9.7.1 Rebooting the Camera ....................................................................................................82
9.7.2 Restoring Default Settings..............................................................................................83
9.7.3 Exporting / Importing Configuration File.......................................................................83
9.7.4 Upgrading the System.....................................................................................................84
9.8 RS-232 Settings..................................................................................................... 84
9.9 RS-485 Settings..................................................................................................... 85
9.10 Fisheye Parameters.............................................................................................. 86

User Manual of Network Fisheye Camera
7
Appendix.....................................................................................................................88
Appendix 1 SADP Software Introduction....................................................................... 88
Appendix 2 Port Mapping................................................................................................ 91

User Manual of Network Fisheye Camera
8
Chapter 1 System Requirement
Operating System: Microsoft Windows XP SP1 and above version / Vista / Win7 /
Server 2003 / Server 2008 32bits
CPU: Intel Pentium IV 3.0 GHz or higher
RAM: 1G or higher
Display: 1024×768 resolution or higher
Web Browser: Internet Explorer 6.0 and above version, Safari 5.02 and above
version, Mozilla Firefox 3.5 and above version and Google Chrome8 and above
versions.

User Manual of Network Fisheye Camera
9
Chapter 2 Network Connection
Before you start:
If you want to set the network camera via a LAN (Local Area Network), please
refer to Section 2.1 Setting the Network Camera over the LAN.
If you want to set the network camera via a WAN (Wide Area Network), please
refer to Section 2.2 Setting the Network Camera over the WAN.
2.1 Setting the Network Camera over the LAN
Purpose:
To view and configure the camera via a LAN, you need to connect the network
camera in the same subnet with your computer, and install the SADP or iVMS-4200
software to search and change the IP of the network camera.
Note: For the detailed introduction of SADP, please refer to Appendix 1.
2.1.1 Wiring over the LAN
The following figures show the two ways of cable connection of a network camera
and a computer:
Purpose:
To test the network camera, you can directly connect the network camera to the
computer with a network cable as shown in Figure 2-1.
Refer to the Figure 2-2 to set network camera over the LAN via a switch or a
router.
Figure 2-1 Connecting Directly

User Manual of Network Fisheye Camera
10
Figure 2-2 Connecting via a Switch or a Router
2.1.2 Detecting and Changing the IPAddress
You need the IP address to visit the network camera.
Steps:
1. To get the IP address, you can choose either of the following methods:
Use SADP, a software tool which can automatically detect the online
network cameras in the LAN and list the device information including IP
address, subnet mask, port number, device serial number, device version, etc.,
shown in Figure 2-3.
Use the iVMS-4200 client software to list the online devices. Please refer to
the user manual of iVMS-4200 client software for detailed information.
2. Change the IP address and subnet mask to the same subnet as that of your
computer.
3. Enter the IP address of network camera in the address field of the web browser to
view the live video.
Notes:
The default IP address is 192.0.0.64 and the port number is 8000. The default user
name is admin, and password is 12345. And you are highly recommended change
the initial password after your first login.
For accessing the network camera from different subnets, please set the gateway
for the network camera after you logged in. For detailed information, please refer
to Section 5.3.1 Configuring TCP/IP Settings.

User Manual of Network Fisheye Camera
11
Figure 2-3 SADP Interface
2.2 Setting the Network Camera over the WAN
Purpose:
This section explains how to connect the network camera to the WAN with a static IP
or a dynamic IP.
2.2.1 Static IP Connection
Before you start:
Please apply a static IP from an ISP (Internet Service Provider). With the static IP
address, you can connect the network camera via a router or connect it to the WAN
directly.
Connecting the network camera via a router
Steps:
1. Connect the network camera to the router.

User Manual of Network Fisheye Camera
12
2. Assign a LAN IP address, the subnet mask and the gateway. Refer to Section 2.1.2
Detecting and Changing the IP Address for detailed IP address configuration of
the camera.
3. Save the static IP in the router.
4. Set port mapping, e.g., 80, 8000, and 554 ports. The steps for port mapping vary
according to the different routers. Please call the router manufacturer for
assistance with port mapping.
Note: Refer to Appendix 2 for detailed information about port mapping.
5. Visit the network camera through a web browser or the client software over the
internet.
Figure 2-4 Accessing the Camera through Router with Static IP
Connecting the network camera with static IPdirectly
You can also save the static IP in the camera and directly connect it to the internet
without using a router. Refer to Section 2.1.2 Detecting and Changing the IP Address
for detailed IP address configuration of the camera.
Figure 2-5 Accessing the Camera with Static IP Directly
2.2.2 Dynamic IP Connection
Before you start:
Please apply a dynamic IP from an ISP. With the dynamic IP address, you can connect
the network camera to a modem or a router.
Connecting the network camera via a router
Steps:

User Manual of Network Fisheye Camera
13
1. Connect the network camera to the router.
2. In the camera, assign a LAN IP address, the subnet mask and the gateway. Refer
to Section 2.1.2 Detecting and Changing the IP Address for detailed LAN
configuration.
3. In the router, set the PPPoE user name, password and confirm the password.
4. Set port mapping. E.g. 80, 8000, and 554 ports. The steps for port mapping vary
depending on different routers. Please call the router manufacturer for assistance
with port mapping.
Note: Refer to Appendix 2 for detailed information about port mapping.
5. Apply a domain name from a domain name provider.
6. Configure the DDNS settings in the setting interface of the router.
7. Visit the camera via the applied domain name.
Connecting the network camera via a modem
Purpose:
This camera supports the PPPoE auto dial-up function. The camera gets a public IP
address by ADSL dial-up after the camera is connected to a modem. You need to
configure the PPPoE parameters of the network camera. Refer to Section 5.3.3
Configuring PPPoE Settings for detailed configuration.
Figure 2-6 Accessing the Camera with Dynamic IP
Note: The obtained IP address is dynamically assigned via PPPoE, so the IP address
always changes after rebooting the camera. To solve the inconvenience of the
dynamic IP, you need to get a domain name from the DDNS provider (E.g.
DynDns.com). Please follow the steps below for normal domain name resolution and
private domain name resolution to solve the problem.
Normal Domain Name Resolution

User Manual of Network Fisheye Camera
14
Figure 2-7 Normal Domain Name Resolution
Steps:
1. Apply a domain name from a domain name provider.
2. Configure the DDNS settings in the DDNS Settings interface of the network
camera. Refer to Section 5.3.4 Configuring DDNS Settings for detailed
configuration.
3. Visit the camera via the applied domain name.
Private Domain Name Resolution
Figure 2-8 Private Domain Name Resolution
Steps:
1. Install and run the IP Server software in a computer with a static IP.
2. Access the network camera through the LAN with a web browser or the client
software.
3. Enable DDNS and select IP Server as the protocol type. Refer to Section 5.3.4
Configuring DDNS Settings for detailed configuration.

User Manual of Network Fisheye Camera
15
Chapter 3 Access to the Network
Camera
3.1 Accessing by Web Browsers
Steps:
1. Open the web browser.
2. Input the IP address of the network camera in the address bar, e.g., 192.0.0.64 and
press the Enter key to enter the login interface.
3. Input the user name and password and click Login.
Figure 3-1 Login Interface
Notes:
The default user name is admin, and the default password is 12345.
Switch the display language from the upper-right corner between Chinese and
English.
4. Install the plug-in before viewing the live video and operating the camera. Please
follow the installation prompts to install the plug-in.

User Manual of Network Fisheye Camera
16
Figure 3-2 Download and Install Plug-in
Figure 3-3 Install Plug-in (1)
Figure 3-4 Install Plug-in (2)
Note: You may have to close the web browser to install the plug-in. Please reopen the
web browser and log in again after installing the plug-in.

User Manual of Network Fisheye Camera
17
3.2 Accessing by Client Software
The product CD contains the iVMS-4200 client software. You can view the live video
and manage the camera with the software.
Follow the installation prompts to install the software. The control panel and live view
interface of iVMS-4200 client software are shown as bellow.
Figure 3-5 iVMS-4200 Client Software
Note: For detailed information about the software, please refer to the user manual of
the iVMS-4200 Client Software.

User Manual of Network Fisheye Camera
18
Chapter 4 Live View
4.1 Live View Page
Purpose:
The live view page allows you to view the real-time video, capture images, realize
PTZ control, set/call presets and configure video parameters.
Log in the network camera to enter the live view page, or you can click Live View on
the menu bar of the main page to enter the live view page.
Descriptions of the live view page:
Figure 4-1 Live View Page
Menu Bar:
Click the tab to enter Live View, Playback, Log and Configuration page respectively.
Layout Control:
Click each tab to adjust the layout of the live view. 4:3, 16:9, and auto are selectable.
Live View Mode:
Display the live video in Fisheye View, Panorama View, or PTZ View.
Fisheye View: In the Fisheye View mode, the whole wide-angle view of the
fisheye camera is displayed. This view mode is called Fisheye View because it

User Manual of Network Fisheye Camera
19
approximates the vision of a fish’s convex eye. The lens produces curvilinear
images of a large area, while distorting the perspective and angles of objects in
the image.
Panorama View: In the Panorama View mode, the distorted fisheye image is
transformed to normal perspective image by some calibration methods.
PTZ View: The PTZ View is the close-up view of some defined area in the
Fisheye View or Panorama View, and it supports the electronic PTZ function,
which is also called e-PTZ.
Note: Each PTZ View is marked on the Fisheye View and Panorama View with a
specific navigation box.
Live View Window:
Display the live view in fisheye mode, panorama mode, or PTZ mode.
Toolbar:
Start / Stop the live view, enable / disable the two-way audio, adjust the audio volume,
capture pictures and record the video files.
PTZ Control:
Realize the pan / tilt / zoom function of PTZ view via the navigation box, and set the
PTZ moving speed.
Preset/Patrol Settings:
Set and call the preset/patrol for the camera.
4.2 Starting Live View
In the live view window as shown in Figure 4-2, click on the toolbar to start the
live view of the camera.
Figure 4-2 Live View Toolbar
Table 4-1 Descriptions of the Toolbar
Icon
Description
/
Start/Stop live view.