Hilti NURON SID 6--22 User manual

SID 6-22 English 1
Français 17
Español 35
Português 53

1

2
3
4

SID 6-22
en Original operating instructions . . . . . . . . . . . . . . . . . . . . . . . . . . 1
fr Moded'emploioriginal ............................... 17
es Manual de instrucciones original . . . . . . . . . . . . . . . . . . . . . . . 35
pt Manual de instruções original . . . . . . . . . . . . . . . . . . . . . . . . . . 53

*2274162* 2274162 English 1
Original operating instructions
1 Information about the documentation
1.1 About this documentation
• Read this documentation before initial operation or use. This is a
prerequisite for safe, trouble-free handling and use of the product.
• Observe the safety instructions and warnings in this documentation and
on the product.
• Always keep the operating instructions with the product and make sure
that the operating instructions are with the product when it is given to
other persons.
1.2 Explanation of symbols
1.2.1 Warnings
Warnings alert persons to hazards that occur when handling or using the
product. The following signal words are used:
DANGER
DANGER !
▶Draws attention to imminent danger that will lead to serious personal
injury or fatality.
WARNING
WARNING !
▶Draws attention to a potential threat of danger that can lead to serious
injury or fatality.
CAUTION
CAUTION !
▶Draws attention to a potentially dangerous situation that could lead to
personal injury or damage to the equipment or other property.
1.2.2 Symbols in the operating instructions
The following symbols are used in these operating instructions:
Comply with the operating instructions
Instructions for use and other useful information
Dealing with recyclable materials
Do not dispose of electric equipment and batteries as household
waste
Hilti Liion battery
Hilti charger

2 English 2274162 *2274162*
1.2.3 Symbols in illustrations
The following symbols are used in illustrations:
These numbers refer to the illustrations at the beginning of these
operating instructions.
The numbering reflects the sequence of operations shown in the
illustrations and may deviate from the steps described in the text.
Item reference numbers are used in the overview illustration and
refer to the numbers used in the key in the product overview sec-
tion.
These characters are intended to specifically draw your attention to
certain points when handling the product.
1.3 Product-dependent symbols
1.3.1 Additional symbols
The following symbols can be used additionally in this documentation or on
the product:
The device supports near-field communication (NFC) technology
compatible with iOS and Android platforms.
Hilti Li-ion battery type series used. Observe the information given in
the section headed Intended use.
Rated speed under no load
Direct current (DC)
Revolutions per minute
Forward / reverse
Li-ion battery
Never use the battery as a striking tool.
Do not drop the battery. Never use a battery that has suffered an
impact or is damaged in any other way.
If applied on the product, the product has been certified by this cer-
tification body for the US and Canadian markets according to the
applicable standards.
1.4 Product information
products are designed for professional users and only trained,
authorized personnel are permitted to operate, service and maintain the
products. This personnel must be specifically informed about the possible
hazards. The product and its ancillary equipment can present hazards if
used incorrectly by untrained personnel or if used not in accordance with
the intended use.

*2274162* 2274162 English 3
The type designation and serial number are printed on the rating plate.
▶Write down the serial number in the table below. You will be required to
state the product details when contacting Hilti Service or your local Hilti
organization to inquire about the product.
Product information
Cordless impact wrench SID 622
Generation 01
Serial no.
2 Safety
2.1 General power tool safety warnings
WARNING Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all instruc-
tions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
Work area safety
▶Keep work area clean and well lit. Cluttered or dark areas invite
accidents.
▶Do not operate power tools in explosive atmospheres, such as in
the presence of flammable liquids, gases or dust. Power tools create
sparks which may ignite the dust or fumes.
▶Keep children and bystanders away while operating a power tool.
Distractions can cause you to lose control.
Electrical safety
▶Power tool plugs must match the outlet. Never modify the plug in
any way. Do not use any adapter plugs with earthed (grounded)
power tools. Unmodified plugs and matching outlets will reduce risk of
electric shock.
▶Avoid body contact with earthed or grounded surfaces, such as
pipes, radiators, ranges and refrigerators. There is an increased risk
of electric shock if your body is earthed or grounded.
▶Do not expose power tools to rain or wet conditions. Water entering
a power tool will increase the risk of electric shock.
▶Do not abuse the cord. Never use the cord for carrying, pulling or
unplugging the power tool. Keep cord away from heat, oil, sharp
edges or moving parts. Damaged or entangled cords increase the risk
of electric shock.
▶When operating a power tool outdoors, use an extension cord
suitable for outdoor use. Use of a cord suitable for outdoor use
reduces the risk of electric shock.

4 English 2274162 *2274162*
▶If operating a power tool in a damp location is unavoidable, use
a residual current device (RCD) protected supply. Use of an RCD
reduces the risk of electric shock.
Personal safety
▶Stay alert, watch what you are doing and use common sense when
operating a power tool. Do not use a power tool while you are tired
or under the influence of drugs, alcohol or medication. A moment
of inattention while operating power tools may result in serious personal
injury.
▶Use personal protective equipment. Always wear eye protection.
Protective equipment such as a dust mask, non-skid safety shoes, hard
hat or hearing protection used for appropriate conditions will reduce
personal injuries.
▶Prevent unintentional starting. Ensure the switch is in the off-
position before connecting to power source and/or battery pack,
picking up or carrying the tool. Carrying power tools with your finger
on the switch or energising power tools that have the switch on invites
accidents.
▶Remove any adjusting key or wrench before turning the power tool
on. A wrench or a key left attached to a rotating part of the power tool
may result in personal injury.
▶Do not overreach. Keep proper footing and balance at all times. This
enables better control of the power tool in unexpected situations.
▶Dress properly. Do not wear loose clothing or jewellery. Keep your
hair and clothing away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
▶If devices are provided for the connection of dust extraction and
collection facilities, ensure these are connected and properly used.
Use of dust collection can reduce dust-related hazards.
▶Do not let familiarity gained from frequent use of tools allow you
to become complacent and ignore tool safety principles. A careless
action can cause severe injury within a fraction of a second.
Power tool use and care
▶Do not force the power tool. Use the correct power tool for your
application. The correct power tool will do the job better and safer at
the rate for which it was designed.
▶Do not use the power tool if the switch does not turn it on and off.
Any power tool that cannot be controlled with the switch is dangerous
and must be repaired.
▶Disconnect the plug from the power source and/or remove the
battery pack, if detachable, from the power tool before making any
adjustments, changing accessories, or storing power tools. Such
preventive safety measures reduce the risk of starting the power tool
accidentally.

*2274162* 2274162 English 5
▶Store idle power tools out of the reach of children and do not
allow persons unfamiliar with the power tool or these instructions
to operate the power tool. Power tools are dangerous in the hands of
untrained users.
▶Maintain power tools and accessories. Check for misalignment or
binding of moving parts, breakage of parts and any other condition
that may affect the power tool’s operation. If damaged, have the
power tool repaired before use. Many accidents are caused by poorly
maintained power tools.
▶Keep cutting tools sharp and clean. Properly maintained cutting tools
with sharp cutting edges are less likely to bind and are easier to control.
▶Use the power tool, accessories and tool bits etc. in accordance
with these instructions, taking into account the working conditions
and the work to be performed. Use of the power tool for operations
different from those intended could result in a hazardous situation.
▶Keep handles and grasping surfaces dry, clean and free from oil and
grease. Slippery handles and grasping surfaces do not allow for safe
handling and control of the tool in unexpected situations.
Battery tool use and care
▶Recharge only with the charger specified by the manufacturer. A
charger that is suitable for one type of battery pack may create a risk of
fire when used with another battery pack.
▶Use power tools only with specifically designated battery packs. Use
of any other battery packs may create a risk of injury and fire.
▶When battery pack is not in use, keep it away from other metal
objects, like paper clips, coins, keys, nails, screws or other small
metal objects, that can make a connection from one terminal to
another. Shorting the battery terminals together may cause burns or a
fire.
▶Under abusive conditions, liquid may be ejected from the battery;
avoid contact. If contact accidentally occurs, flush with water. If
liquid contacts eyes, additionally seek medical help. Liquid ejected
from the battery may cause irritation or burns.
▶Do not use a battery pack or tool that is damaged or modified.
Damaged or modified batteries may exhibit unpredictable behaviour
resulting in fire, explosion or risk of injury.
▶Do not expose a battery pack or tool to fire or excessive temperature.
Exposure to fire or temperature above 130° C (265 °F) may cause
explosion.
▶Follow all charging instructions and do not charge the battery pack
or tool outside the temperature range specified in the instructions.
Charging improperly or at temperatures outside the specified range may
damage the battery and increase the risk of fire.

6 English 2274162 *2274162*
Service
▶Have your power tool serviced by a qualified repair person using
only identical replacement parts. This will ensure that the safety of the
power tool is maintained.
▶Never service damaged battery packs. Service of battery packs should
only be performed by the manufacturer or authorized service providers.
2.2 Safety warnings for screwdrivers and impact wrenches
▶Hold the power tool by insulated gripping surfaces, when performing
an operation where the fastener may contact hidden wiring. Fasten-
ers contacting a "live" wire may make exposed metal parts of the power
tool "live" and could give the operator an electric shock.
2.3 Additional safety instructions
▶Use the product and accessories only when they are in perfect working
order.
▶Never tamper with or modify the product or accessories in any way.
▶Before beginning work, check the working area for concealed electric
cables or gas and water pipes. External metal parts of the product could
give you an electric shock or cause an explosion if you accidentally
damage an electric cable or a gas or water pipe.
▶Keep the air vents clear at all times. Risk of burn injuries due to blocked
air vents!
▶Avoid touching rotating parts – risk of injury!
▶Wear eye protection, a hard hat and ear protection while the product is
in use.
▶Wear protective gloves when changing the accessory tool. Touching the
accessory tool can result in cuts and burns.
▶Wear eye protection. Flying fragments present a risk of injury to the body
and eyes.
▶Dust produced by grinding, sanding, cutting and drilling can contain
dangerous chemicals. Some examples are: lead or lead-based paints;
brick, concrete and other masonry products, natural stone and other
products containing silicates; certain types of wood, such as oak,
beech and chemically treated wood; asbestos or materials that contain
asbestos. Determine the exposure of the operator and bystanders
by means of the hazard classification of the materials to be worked.
Implement the necessary measures to restrict exposure to a safe level,
for example by the use of a dust collection system or by the wearing
of suitable respiratory protection. The general measures for reducing
exposure include:
▶working in an area that is well ventilated,
▶avoidance of prolonged contact with dust,

*2274162* 2274162 English 7
▶directing dust away from the face and body,
▶wearing protective clothing and washing exposed areas of the skin
with water and soap.
▶Take frequent breaks and do physical exercises to improve the blood
circulation in your fingers. High vibration during long periods of work can
lead to disorders of the blood vessels and nervous system in the fingers,
hands and wrists.
▶Do not look directly into the light source (LED) of the product and do not
aim the beam at other persons’ faces. Risk of dazzling or eye damage.
▶Switch the product on only after you have brought it to the working
position.
▶Wait until the product has come to a complete stop before you lay it
down.
▶Risk of injury by falling tools and/or accessories. Before starting work,
check that the battery and installed accessories are secure.
2.4 Battery use and care
▶Comply with the following safety instructions for the safe handling
and use of Li-ion batteries. Failure to comply can lead to skin irritation,
severe corrosive injury, chemical burns, fire and/or explosion.
▶Use only batteries that are in perfect working order.
▶Treat batteries with care in order to avoid damage and prevent leakage
of fluids that are extremely harmful to health!
▶Do not under any circumstances modify or tamper with batteries!
▶Do not disassemble, crush or incinerate batteries and do not subject
them to temperatures over 80 °C (176 °F).
▶Never use or charge a battery that has suffered an impact or been
damaged in any other way. Check your batteries regularly for signs of
damage.
▶Never use recycled or repaired batteries.
▶Never use the battery or a battery-operated power tool as a striking tool.
▶Never expose batteries to the direct rays of the sun, elevated tempera-
ture, sparking, or open flame. This can lead to explosions.
▶Do not touch the battery poles with your fingers, tools, jewelry, or other
electrically conductive objects. This can damage the battery and also
cause material damage and personal injury.
▶Keep batteries away from rain, moisture and liquids. Penetrating moisture
can cause short circuits, electric shock, burns, fire and explosions.
▶Use only chargers and power tools approved for the specific battery
type. Read and follow the relevant operating instructions.
▶Do not use or store the battery in explosive environments.

8 English 2274162 *2274162*
▶If the battery is too hot to touch, it may be defective. Put the battery
in a place where it is clearly visible and where there is no risk of fire,
at an adequate distance from flammable materials. Allow the battery
to cool down. If it is still too hot to touch after an hour, the battery is
faulty. Consult Hilti Service or read the document entitled "Instructions
on safety and use for Hilti Li-ion batteries".
Observe the special guidelines applicable to the transport, storage
and use of lithium-ion batteries. → page 14
Read the instructions on safety and use of Hilti Li-ion batteries
that you can access by scanning the QR code at the end of these
operating instructions.
3 Description
3.1 Product overview 1
@Chuck (1⁄4″ hex socket) with
locking sleeve
;Work-area light (LED)
=Forward/reverse switch with
switch-on interlock
%Control switch (with electronic
speed control)
&Grip
(Installation opening for acces-
sories
)Battery
+Battery release button
§Battery status indicator
/Mode selector
:Mode indicator
3.2 Intended use
The product described is a hand-held cordless impact wrench. It is designed
for driving and removing screws and for tightening and releasing nuts and
bolts in wood, metal, masonry and concrete.
• For this product, use only Hilti Nuron lithium-ion batteries of the B 22
series. For optimum performance, Hilti recommends the batteries stated
in the table at the end of these operating instructions for this product.
• For these batteries, use only Hilti chargers of the type series stated in
the table at the end of these operating instructions.
3.3 Items supplied
Impact wrench, operating instructions
Other system products approved for use with this product can be found at
your local Hilti Store or at: www.hilti.group
3.4 Status indicators of the Liion battery
Hilti Nuron Li-ion batteries can indicate state of charge, fault messages and
the battery's state of health.

*2274162* 2274162 English 9
3.4.1 Indicators for state of charge and fault messages
WARNING
Risk of injury by a falling battery!
▶If the release button is pressed with a battery inserted in the product,
subsequently check that the battery is correctly re-engaged and secure.
Short-press the release button of the battery to get whichever of the following
status indications is applicable at the time.
State of charge and, if applicable, faults are indicated constantly as long as
the connected product is switched on.
Status Meaning
Four (4) LEDs show constantly
green
State of charge: 100 % to 71 %
Three (3) LEDs show constantly
green
State of charge: 70 % to 51 %
Two (2) LEDs show constantly
green
State of charge: 50 % to 26 %
One (1) LED shows constantly
green
State of charge: 25 % to 10 %
One (1) LED slow-flashes green State of charge: < 10 %
One (1) LED quick-flashes green The Li-ion battery is completely
discharged. Recharge the battery.
If the LED again starts
quick-flashing after the battery has
been charged, consult Hilti Service.
One (1) LED quick-flashes yellow The Li-ion battery or the product in
which it is inserted is overloaded,
too hot or too cold, or experiencing
some other fault.
Bring the product and the battery
to the recommended working tem-
perature and do not overload the
product when it is in use.
If the message persists, consult
Hilti Service.
One (1) LED shows yellow The Li-ion battery and the product
in which it is inserted are not com-
patible. Consult Hilti Service.
One (1) LED quick-flashes red The Li-ion battery is locked and
cannot be used. Consult Hilti Ser-
vice.

10 English 2274162 *2274162*
3.4.2 Indicators showing the battery's state of health
To check the battery's state of health, press the release button and hold it
down for longer than three seconds. The system does not detect a potential
malfunction of the battery due to misuse, for example battery dropped or
pierced, external heat damage, etc.
Status Meaning
All LEDs show in sequence, fol-
lowed by one (1) LED showing con-
stantly green.
The battery can remain in use.
All LEDs show in sequence, fol-
lowed by one (1) LED quick-flashing
yellow.
The check to ascertain the battery's
state of health did not complete.
Repeat the procedure, or consult
Hilti Service.
All LEDs show in sequence, fol-
lowed by one (1) LED showing con-
stantly red.
If a connected product can still be
used, the remaining battery capac-
ity is below 50 %.
If a connected product can no
longer be used, the battery has
reached the end of its useful life
and has to be replaced. Consult
Hilti Service.
4 Technical data
Rated voltage 21.6 V
Weight without battery 1.0 kg
(2.2 lb)
Torque adjustment 3 settings
Rated speed under no load Setting I 0 /min …
1,800 /min
Setting II 0 /min …
2,700 /min
Setting III 0 /min …
3,600 /min
Impact speed ≤ 4,250 bpm
Large standard bolts M8 to M16
Large high-strength bolts M6 to M12
Socket/bit drive ¹⁄₄" hex socket
with locking
sleeve

*2274162* 2274162 English 11
Storage temperature −20 ℃ … 70 ℃
(−4 ℉ … 158 ℉)
Ambient temperature for operation −17 ℃ … 60 ℃
(1 ℉ … 140 ℉)
4.1 Battery
Battery operating voltage 21.6 V
Weight, battery See the end of
these operating
instructions
Ambient temperature for operation −17 ℃ … 60 ℃
(1 ℉ … 140 ℉)
Storage temperature −20 ℃ … 40 ℃
(−4 ℉ … 104 ℉)
Battery charging starting temperature −10 ℃ … 45 ℃
(14 ℉ … 113 ℉)
5 Preparations at the workplace
WARNING
Risk of injury by inadvertent starting!
▶Before inserting the battery, make sure that the product is switched off.
▶Remove the battery before making any adjustments to the power tool or
before changing accessories.
Observe the safety instructions and warnings in this documentation and on
the product.
5.1 Charging the battery
1. Before charging the battery, read the operating instructions for the
charger.
2. Make sure that the contacts on the battery and the contacts on the
charger are clean and dry.
3. Use an approved charger to charge the battery. → page 8
5.2 Inserting the battery
WARNING
Risk of injury by short circuit or falling battery!
▶Before inserting the battery, make sure that the contacts on the battery
and the contacts on the product are free of foreign matter.
▶Make sure that the battery always engages correctly.
1. Charge the battery fully before using it for the first time.

12 English 2274162 *2274162*
2. Push the battery into the product until it engages with an audible click.
3. Check that the battery is seated securely.
5.3 Removing the battery
1. Press the battery release button.
2. Remove the battery from the product.
5.4 Changing the accessory tool 2
CAUTION
Risk of injury by the accessory tool! The accessory tool might be hot or
have sharp edges.
▶Wear protective gloves when changing the accessory tool.
1. Check that the connection end of the accessory tool is clean. Clean the
connection end if necessary.
2. To insert the accessory tool push it into the chuck as far as it will go,
until the locking sleeve engages with an audible click. Check that the
accessory tool is held securely.
3. To remove the accessory tool, pull the locking sleeve forward and hold
it in this position.
4. Pull the accessory tool out of the chuck and release the locking sleeve.
5.5 Fall arrest
WARNING
Risk of injury by falling tool and/or accessory!
▶Use only the Hilti tool tether recommended for your product.
▶Prior to each use, always check the attachment point of the tool tether
for possible damage.
▶Do not secure a tool tether to the belt hook. Do not use a belt hook to lift
the product.
Comply with the national regulations for working at heights.
As drop arrester for this product, use only a combination of the Hilti retaining
strap and the Hilti tool tether #2261970.
▶Secure the retaining strap to the installation openings for accessories.
Check that it holds securely.
▶Secure one carabiner of the tool tether to the retaining strap and secure
the second carabiner to a load-bearing structure. Check that both
carabiners hold securely.
Comply with the operating instructions of the Hilti retaining strap
and those of the Hilti tool tether.

*2274162* 2274162 English 13
6 Operation
Observe the safety instructions and warnings in this documentation and on
the product.
6.1 Selecting mode 3
1. Repeatedly press the mode selector until the mode indicator shows the
speed stage you want to use.
2. To switch the light on for 2 minutes, simultaneously press the mode
selector and the control switch for at least 0.5 seconds.
▶The LEDs for the mode indicator go out.
6.2 Setting forward or reverse rotation 4
▶Set the forward/reverse switch to the desired direction of rotation.
▶The control switch is locked when the forward/reverse switch is in the
middle position (switch-on interlock).An interlock prevents switching
while the motor is running.
6.3 Switching on and off
1. Press the control switch.
▶The product starts.
Speed can be controlled steplessly by varying how far the control
switch is pressed in.
2. Release the control switch.
▶The product switches off.
7 Care and maintenance
WARNING
Risk of injury with battery inserted !
▶Always remove the battery before carrying out care and maintenance
tasks!
Care of the product
• Carefully remove stubborn dirt.
• Carefully clean the air vents, if present, with a dry, soft brush.
• Use only a slightly damp cloth to clean the housing. Do not use cleaning
agents containing silicone as these can attack the plastic parts.
• Use a dry, clean cloth to clean the contacts of the product.
Care of the Liion batteries
• Never use a battery with clogged air vents. Clean the air vents carefully
using a dry, soft brush.

14 English 2274162 *2274162*
• Avoid unnecessary exposure of the battery to dust and dirt. Never
expose the battery to high levels of moisture (e.g. by being dipped in
water or left in the rain).
If a battery has been soaked by moisture, treat it as a damaged battery.
Isolate it in a non-flammable container and consult Hilti Service.
• Keep the battery free of extraneous oil and grease. Do not permit dust
or dirt to accumulate unnecessarily on the battery. Clean the battery
with a dry, soft brush or a clean, dry cloth. Do not use cleaning agents
containing silicone as these can attack the plastic parts.
Do not touch the contacts of the battery and do not remove the factory-
applied grease from the contacts.
• Use only a slightly damp cloth to clean the housing. Do not use cleaning
agents containing silicone as these can attack the plastic parts.
Maintenance
• Check all visible parts and controls for signs of damage at regular
intervals and make sure that they all function correctly.
• Do not use the product if signs of damage are found or if parts
malfunction. Immediately have the product repaired by Hilti Service.
• After cleaning and maintenance, install all guards and protective devices
and check that they are in full working order.
To help ensure safe and reliable operation, use only genuine Hilti spare
parts and consumables. Spare parts, consumables and accessories
approved by Hilti for use with your product can be found at your
Hilti Store or online at: www.hilti.group
8 Transport and storage of cordless tools and batteries
Transport
CAUTION
Accidental starting during transport !
▶Always transport your products with the batteries removed!
▶Remove the battery/batteries.
▶Never transport batteries loose and unprotected. During transport,
batteries should be protected from excessive shock and vibration and
isolated from any conductive materials or other batteries that may come
in contact with the terminals and cause a short circuit. Comply with the
locally applicable regulations for transporting batteries.
▶Do not send batteries through the mail. Consult your shipper for
instructions on how to ship undamaged batteries.
▶Prior to each use and before and after prolonged transport, check the
product and the batteries for damage.

*2274162* 2274162 English 15
Storage
WARNING
Accidental damage caused by defective or leaking batteries !
▶Always store your products with the batteries removed!
▶Store the product and the batteries in a cool and dry place. Comply with
the temperature limits stated in the technical data.
▶Do not store batteries on the charger. Always remove the battery from
the charger when the charging operation has completed.
▶Never leave batteries in direct sunlight, on sources of heat, or behind
glass.
▶Store the product and batteries where they cannot be accessed by
children or unauthorized persons.
▶Prior to each use and before and after prolonged storage, check the
product and the batteries for damage.
9 Troubleshooting
If a problem occurs, always observe the charge-status and fault indicator of
the battery. See the section headed Status indicators of the Liion battery.
If the trouble you are experiencing is not listed in this table or you are unable
to remedy the problem by yourself, please contact Hilti Service.
Trouble or fault Possible cause Action to be taken
Product does not
work.
The battery is not fully
inserted.
▶Push the battery in
until it engages with
an audible click.
Running speed sud-
denly drops consid-
erably.
Battery is discharged. ▶Change the battery
and charge the empty
battery.
The battery runs
down more quickly
than usual.
Very low ambient tem-
perature.
▶Allow the battery to
warm up slowly to
room temperature.
The battery doesn’t
engage with an audi-
ble click.
The retaining lugs on the
battery are dirty.
▶Clean the retaining
lugs and engage the
battery in the working
position.
Product or battery
gets very hot.
Electrical fault. ▶Switch the product off
immediately, remove
the battery, keep it
under observation,
allow it to cool down
and contact Hilti
Service.

16 English 2274162 *2274162*
Trouble or fault Possible cause Action to be taken
LEDs of the battery
show nothing
Battery defective. ▶Contact Hilti Service.
10 Disposal
WARNING
Risk of injury due to incorrect disposal! Health hazards due to escaping
gases or liquids.
▶DO NOT send batteries through the mail!
▶Cover the terminals with a non-conductive material (such as electrical
tape) to prevent short circuiting.
▶Dispose of your battery out of the reach of children.
▶Dispose of the battery at your Hilti Store, or consult your local gov-
ernmental garbage disposal or public health and safety resources for
disposal instructions.
Most of the materials from which Hilti products are manufactured can
be recycled. The materials must be correctly separated before they can
be recycled. In many countries, your old tools, machines or appliances
can be returned to Hilti for recycling. Ask Hilti Service or your Hilti sales
representative for further information.
▶Do not dispose of power tools, electronic equipment or batteries as
household waste!
11 FCC statement (applicable in US) / IC statement (applica-
ble in Canada)
This device complies with Part 15 of the FCC Rules and RSS-210 of lC.
Operation is subject to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference
that may cause undesired operation.
12 Manufacturer’s warranty
▶Please contact your local Hilti representative if you have questions about
the warranty conditions.
13 Further information
For more information on operation, technology, environment and recycling,
follow this link: qr.hilti.com/manual?id=2274162
This link is also to be found at the end of the documentation, in the form of
a QR code.