Hiltron security DX4000 User manual

!Functioning programmable separately
in bistable and monostable
!Combination possible codes rolling code
!Activatione of output through application of buttons
!Visualization of memorized codes
!Self-learning of new codes directly from remote-control.
!Timing of monostable until 90sec.
!Power Supply 12 Vcc
!Maximum absorption: 110 mA @ 12 V
!Absorption in standby with BIRD connected 25mA of 12 V
!LED signal of active output
!Output relay 4 C/NA/NC 1A
!Dimensions: 87x 63mm
Decoder quad channel rolling code for rem. QUAD
DX4000
1
DX4000 is a decoder quad channel rolling
code associated to the antenna with
receiver BIRD dotated of four relays in
output piloted from four bottons
(Channels A, B,C and D)of remote-control QUAD.
The circuit DX4000 can programm from 1 to
1400 remote-control QUAD
Use a cable of two conductors + display
(type 2S) to connect the antenna BIRD to terminal
block of DX4000, respecting the connections “1”
and“2”.
It’s advisable not to pass this cable of connection to
the antenna BIRD with others cables.
NOTE : Once that the functions are decided of 4
output of DX4000, it’s possible to test directly from
the circuit by making a double pression on one of the
four bottons S1-S2-S3-S4.
The bottons active the relatives output
OUT1-OUT2-OUT3-OUT4
Example: S2 (double pression) command OUT2
INSTALLATION
BIRD
708aMA-1.02
LED2LED1 LED3 LED4
SW2
SW1 SW3 SW4
PT2PT1 PT3 PT4
+
Bistable (0 sec.)
Monostable (until 90 sec.)
ACTIVE
CHANNEL
DISACTIVE
CHANNEL
LED ON
FIXED
LED OFF
1
4
2
3
OUT1
OUT3
OUT2
OUT4
QUAD
Pb
Lead free
RoHS
compliant
Pb
Lead free
RoHS
compliant
Pb
Lead free
RoHS
compliant
Pb
Lead free
RoHS
compliant
RAEE
security
Made in Italy
BT2014/35/UE
EMC2014/30/UE

DX4000
1 ACQUISITION AND PROGRAMMING NEW REMOTE CONTROL QUAD
1.1 To enter in programming,press at the same time at the same time the buttons Sw1and SW2.
The circuit enter in modality “WAITING FOR QUAD”
During this phase, the circuit DX4000 gives to each remote-controls , automatically, una position(from
0001 to 1400) inside own memory in progressive mode.
LED1 starts to flash.
1.2 Press any button of remote-control QUAD to enter in modality
“EDIT QUAD” *
If the remote-control there isn’t into the memory , the 4 LED on the circuit flashing to indicate that no
output has been enabled.
If the remote-control there is into the memory, the LED1 + LED2 on emitting some flash for a second,
after the channels LED on to indicate programmed ones(led on fixed) and not programmed ones (led
flashing).
In this case, during the acquisition of remote-control flashing all 4 LED.
1.3 Press once the button SW2, will on the related LED2 , for a minute and after the modality of
switching on of led will indciate the output attributed (led off) r free (led on).
1.4 Press the relative button to the output that wants to associate to a button of remote-control (will stay on
the related led).
1.5 Press once the button SW2 to confirm
1.6 Return to point 1.4 to program others output and/or to modificate them, or twice in rapid succession
the button 1to return to madality “WAITING FOR QUAD”, confirmed operation from flah of 4 LED and
to exit from the next flash of only LED1. Press SW1 and Sw2 at the same time to save and to exit from
programming, otherwise after 30 seconds,the circuit exits from programming without
modifications
NOTE: During programming phase is advisable (especially in presence of an elevated number of
remote-controls ) to note on a paper, lthe position of remote-controls programmed and to associate on
the side a description(user, enabled output...).
These notes will serve after to recognise a remote-control through the count of LED easily .
To discover the position assigned to QUAD from the point 1.2
Press once Sw1 to verificate the position associated .
The LED1 will indicate the thousands
The LED2 will indicate the hundreds
The LED3 will indicate the dozens
The LED4 will indicate the units
So for the position n.1, the LED 1,2 and 3 will emit some flash to indicate the value 0 the LED 4 will emit
1 only flashing to indicate 1 , so 0001.
2
security

DX4000
2 REMOVING ASSOCIATION OUTUPUT CIRCUIT - REMOTE- CONTROL
2.1 To enter to programming following the process described to the point 1.1
2.2 To enter in modality “EDIT QUAD” following the process described to the point 1.2
The Led on fixed, will indicate the output already assigned,the ones flashing the free output .
2.3 To remove the association of an output with a remote-control a determinated button of QUAD, press
SW2 (twice), keeping in mind :
LED2 flashing twice - flashing fastly the programmed output on remote-control .
2.4 Press the button on the related circuit to programmed output, to remove (SW1/SW2/SW3/SW4)
The LED associated is off to indicate the correct execution of the operation.
2.5 Press the button SW1 (2 volte) to exit and to bring the circuit in modality “EDIT QUAD”.
2.6 Press twice SW1 to exit from the modality “EDIT QUAD” and after , at the same time SW1 and SW2 to
exit from programming
3 ELIMINATION REMOTE-CONTOL
3.1 To enter in programming following the process described before at the point 1.1
3.2 To enter in modality “EDIT QUAD” 1.2
Press SW3 and SW4 (once)
four LED flashing fastly .
The circuit retourn in to modality “ATTESA QUAD”
3.3 Press at the same time SW1 and Sw2 to exit from the programming .
4 ELIMINATION LOST REMOTE-CONTROL
4.1 To enter in programming following the process described at the point 1.1
4.2 PreSS SW3 keeping in mind that : LED1 stays on fixed .
4.3 The circuit waits the inclusion of the position of remote-control using 4 buttons:
SW1 (thousands 1000) / SW2 (hundreds 100) / SW3 (dozens 10) / SW4 (unity1)
LED1 flashing at every pression of buttons.
4.4 Press SW1 (twice) to confirm the position inserted
4.5 The circuit signal if at the inserted position, there is a remote-control or not :
If there isn’t any remote-control to the inserted position :
LED1 and LED2 turn on , alternating to LED3 and LED4.
If the position is asigned to a remote-control, for a second flashing fastly the
LED 1 and LED2, after the ignition of the LED will indicate the output asignated or not, meaning
LED on fixed , will iondicate the output yet asignated.
Flashing LED will indicate the free output.
4.6 To remove that remote-control, press SW3 and SW4 at the same time
4 LED will emit some flash and the circuit retourns to the modality “WAITING FOR QUAD”.
4.7 Press SW1 and SW2 to exit from programming.
following the process described before at the point
3
security

4
5 VISUALIZATION ASSOCIATIONS OUTPUT CIRCUIT - REMOTE-CONTROL
5.1 To enter in programming following the process described at the point 1.1
5.2 To enter in modality “EDIT QUAD” following the process described before at the point 1.2,
or at the points 4.2, 4.3 and 4.4 if the remote-control there isn’t.
5.3 To visualize the association of the circuit output with remote control , press 3 times SW2
keeping in mind that :
LED2 flashing 3 times turns off all the led .
The circuit is waiting the pression of the button of the output to visualize.
5.4 Press the button SW corresponding to the output of wich you want to visualize the association and
will ignite LED1,2,3 or 4 to indicate than that output is associated the button 1,2,3,or 4 of
remote-control.
5.5 Press 3 times SW1 to retourn to the modality “EDIT QUAD”
5.6 Press again twice SW1 to retourn to modality “WAITING FOR QUAD”
5.7 Press SW1 and SW2 at the same time to exit from programming.
6 TOTAL MEMORY ELIMINATION
6.1 To enter in programming following the process described at the point 1.1
6.3 To enter in modality “EDIT QUAD” following the process described before at the point 1.2 or at the
points 4.2, 4.3 and 4.4 if the remote-control there isn’t .
6.4 To visualize the association of the output circuit with remote-control press 3 times SW2 keeping in
mind that:
LED2 flashing 3 times and off all the LED.
6.5 Press the button SW corresponding to the output of wich they want to visualize the association
and will turns on the led 1,2,3 or 4 to indicate that the output is associated the button 1,2,3 or 4 of
remote-control.
6.6 Press twice SW1 to retourn to the modality “EDIT QUAD”.
6.7 Press again twice SW1 to retourn to modality“WAITING QUAD”
6.8 Press SW1 and SW2 at the same time to exit from programming.
DX4000
708ADE-3.02
Functions button S1
To verificate position remote-control in memorypress ONCE
Press TWICE To retourn to modality “WAITING FOR QUAD”
To associatedcircuit output with remote-control
To remove association output circuit with remote-control
Visualize associations output circuit with remote-control
Functions button S2
Press ONCE
Press TWICE
Press 3 TIMES
Elimination remote-control (QUAD)
Functions button S3 - S4
Press ONCE
FUNCTIONS TABLES BUTTONS Dx4000 (MODALITY EDIT QUAD)
security