Himax B-05 User manual

HIMAX
Electric Screwdriver
B Series DC 20/30V
www.ehimax.com
Operation Instruction
Please Read the Instruction Before Operate
2011/03
Note
This electric screwdriver is designed for indoor use only.
Please do not use it in outdoors or wet environment to prevent
the danger of electrocution.
Pay attention to the voltage specification. Make sure the switch
is in the OFF position when you plug in the power.
Unless you are a trained maintenance personnel, do not
disassemble the device lest it cause dangers or more damages.
Please use the original power transformers for the B model lest
it generates dangers or imprecise torque due to wrong output
specification.
Operating instructions
Make sure the power is switched off to install or replace
screwdriver bits; press the front-end iron cap will allow the
screwdriver bits to be inserted or released.
It is recommended to suspend the electric screwdriver by a
flexible balancer for easy operation and prevent its dropping.
Adjust the torque dial to the proper position according to the
dial/torque table for each model.
The forward/reverse switch should be set to the forward
position when fastening screws. Press the start switch to
complete the operation. The automatic control model will shut
off the power and stop the rotation of the screwdriver bit as
soon as the set torque value is reached.
Position the forward/reverse switch to reverse to loosen screws.
Use hands to hold the electric screwdriver during operation.
Keep it in a perpendicular position with the screw and apply
pressure slightly to prevent slipping.
Use hands or other means to fix the object operated and operate
the electrical power screwdriver safely.
Do not switch the forward/reverse position and improper
switch operations when the motor is running to prevent the
short-circuit of the start switch.
Use it under the normal operation frequency (8 working hours
per day and fasten 800-1000 screws per hour) without
exceeding the operation load will extend the life time of the
electric screwdriver and reduce the occurrences of malfunction.
Please do not use this type of electric screwdriver to fasten
wooden screws.
Regular simple maintenance
Check to see whether all the parts, shell, and power lines are intact
all the time to ensure normal operations. Unplug the power plug and
turn off the power before doing any maintenance operation to ensure
safety. For every 1000 hours operation or half year, the following
cleaning and maintenance operations to the machine body and the
inside are required.
ON/OFF Switch
is on the head of
electric screwdriver
ON/OFF Switch
5P Connector
Trigger
Forward/Reverse
Switch
Torque Dial
Bits Holder Collar
Torque
Adjusting
Nut

2
Output Torque/Adjust Dial
可
User can adjust output torque
via changing the Torque
spring. Please refer to the
torque/dial table and then
turn the “torque adjusting
nut”to set the proper dial for
each model of machine and
set to the desired torque for
operations.
Adjusting torque
The dials on the electric screwdriver do not represent the torque
value
Please use the torque/dial table to set the proper dial for each
different machine type and set to the desired torque for
operations.
To ensure the precision of the torque value, we recommend the
se of the HIMAX torque tester to measure and calibrate.
SOFT STARTAdjustable Time Setting Switch
B series electric screwdrivers possess SOFT START adjustable time
setting switch. User can set the machines to start from lower speed
(350 rpm) for 0.2～4 seconds and then switch to full speed
operating automatically. B series are suitable for assembly lines
which require extreme preciseness.
With five levels to choose: 0.0sec/0.5sec/1sec/2sec/4sec
Carefully take off the tag from
its side, and user can see a small
square opening as the picture
shows.
The adjustable switch is at the
corresponding position inside
the square opening.（See the red
circle on the right picture）
Turn the switch separately to set
the time of SOFT START
Power Supply
Switching Power Supply
BT5A
CLT-50
B series brushless electric screwdrivers must be used with
switching power supply BT5A.
The electric screwdriver connects to the power supply with 5P
connecting wire.
Ascertain that the power supply is connected at 90~240V
50/60Hz, and turn on the power.
By turning the HI/LOW switch, user can adjust the speed of the
electric screwdriver.
Brushless electric screwdriver can also be used with CLT-50
power supply, but the screw counter STC-01 will not function.
Specification
Able to adopt different type of bits
Torque Adjusting Nut