HIOS BLG-IF1 User manual

ET-E011_BLG-IF1_17A
1/2
Instruction Manual
BLG serial-to-parallel Conversion Box BLG-IF1
■Overview
TheBLG-IF1isaconversionboxtoconvert thesignaltransmissionoftheBLG-BC2driverfromserial
communicationtoparallelcommunication.
With theBLG-IF1 thedriver can be interlockedwith externaldevicessuch asaPLCby usingeach oftheinputand
outputsignalsinthe “■Detailsofthe26pinconnector” below.
Byconvertingthesignaltransmissionitiseasytodesignyour productassemblylines.
■DimensionsandSpecifications
■Details ofthe26 pinconnector
(Note:Makesurenottooperatethe driverwhileinputtingthefollowinginputsignalsfrom externaldevices.)
PinNo.
SignalName
Details
Conditions
Input
1
Panel
Operation
Tolock/unlocktheSettingButtonsonthe
driver(Tamperprooffunction)
ON →
thebuttons getlocked
2
Lever Operation
Toturnon/offthedriver
(Thedrivercanbeonasneeded)
ON →
thedriveris turnedoff
3
WorkSensor
Toturnon/offthedriverbyjudging
presenceor absenceoftheworkpiece
ON →
thedriveris turnedon
Output
7
Start
Startsignal
Opencollector
up to35V/100mA
8
T.UP
Finishsignal (eachclutch activation)
9
PASS
Passsignal (Noerrors)
10
Fail
Errorsignal(errorsdetected)
11
COMP
Completionsignal(completionofpreset
cyclecount)
15
GND
GROUND
(RS-232C)
BLG
17
RXD
Connect toTerminal#3 of theD-SUB9P
D-SUB9Pattached
18
TXD
Connect toTerminal#2 of theD-SUB9P
19
GND
Connect toTerminal#5 of theD-SUB9P
(RS-232C)
PC
20
GND
Connect toTerminal#5 of theD-SUB9P
Notattached
21
RXD
Connect toTerminal#2 of theD-SUB9P
22
TXD
Connect toTerminal#3 of theD-SUB9P
Input
power
25
+Vcc
8-28V
26
-Vcc
Common
IF-1
(RS-232C)
BC2
(RS-232C)PC
(OUT)
(IN)

ET-E011_BLG-IF1_17A
2/2
■Accessories
Accessories
No.ofpcs
Details
D-SUB9pin
Maleconnector
1
(PleaseconnectitwiththeBLG-BC2series)
* Note:ToconnectwiththeBLG-BC2
TheBLG-BC2I/OCable“BLG-BC2-3010” needstobepurchasedadditionally.
26pincable
withaconnector
1
(Please connectitwithPLC)
* Note:ToconnectwithaPC
ACommercial D-SUB 9pin connectoranda RS-232Ccable (Straightcable) need
tobepurchasedadditionally.
■Wiring connection
1.TousetheBLG-IF1withthedriver,the attachedD-SUB9 pinconnectorneedstobeinstalledtotheboxto
connectwiththedriver.Adjustthelengthofthe26pincablesandpositionoftheD-SUB9 pinconnectorbased
ontheuseconditions,andconnectthe D-SUB9pin connectorandthe26 pinconnector.
2.Toconnectwithexternal devicessuchasaPLC (Insomeusageconditions,alsoconnect to theCOMasneeded
basis.)
*OptionBLG-BC2I/O Cable
BLG-BC2-3010
* Note: Makesureto turnonthe powersupplyafterdoingallthe necessary wiring connection to prevent malfunction,
andnot tooperate thedriverwhileinputtingthesignalsfromexternaldevices.
ConnectCOM(#5or 6)
toGND.
Todothis connection,
#26needstobe used.
Inputcircuit(reference)
Outputcircuit
*#25and26needtobe
sharedwiththeexternal
inputpowersourcetodo
theconnectionsabove.
ConnectCOMto +V
(8-28V).
To do thisconnection,
#25needstobeused.
Internalcircuit
sinkcurrent
Internalcircuit
Internalcircuit
sourcecurrent
Jackφ2.5
D-SUB 9pinfemale
Length: 3m