Hioth CT-SMZB2004-HM User manual

HIOTH User Manual
HIOTH TECHNOLOGY CO.,LTD.
SMART MOTION SENSOR
Introduction
This product is Smart Motion Sensor, adopts extra low power consumption ZigBee wireless
network and automatic threshold adjustment technology to enhance the stability of the detector,
efficiently anti-false alarm. Automatic temperature compensation technology, can efficiently
prevent detectors from the decrease in sensitivity resulted from the temperature variation. Suitable
to be used for safety protection of residential, villas, factories, shopping malls, warehouses, office
buildings, banks, computer room and other places.
Technical Information
Compatible with any ZigBee network controller
Battery powered and cost savings
High sensitivity, small size
Support the scene control
CT-SMZB2004-HM
Smart motion sensor

HIOTH User Manual
HIOTH TECHNOLOGY CO.,LTD.
Specifications
Radio protocol: ZigBee（IEEE 802.15.4）
Power supply: DC 3V (1 pc 3V CR2450 Button battery))
Standby current：≤16uA
Alarm current：≤30mA
DetectingAngle: 110 degrees
Installation Height: 2.1 m
Detecting Distance: 9-12 m
Working Temperature: -10°C ~ +50°C
Environment Humidity: ≤ 95%RH (no congelation)
RF range: ≤100 m (open area)
Anti RF interference:10MHz-1GHz 20V/m
Dimension: 65x65x28mm
Operation
As shown in figure 1, there is a Reset button on the sides of the Smart Motion Sensor which is
used to carry out inclusion, exclusion or reset. its function is introduced as follows:.
(1) If the Smart Motion Sensor has not been included into the network, short press the Reset
button to enter the network inclusion condition, at this time the network status indicator LED flash
(3 times/second). If the network inclusion success, the network status indicator LED will long on
for 2 seconds and then go out. If the network inclusion failure, the network status indicator LED
will go out.
(2) If the Smart Motion Sensor has been included into the network, and want to include into the
new network, you must reset the device. First, press and hold the Reset button until network status

HIOTH User Manual
HIOTH TECHNOLOGY CO.,LTD.
indicator LED flash once, and then long press the Reset button for 10 seconds, LED will long on
for 3 seconds and then go out. Note: Please loosen the button when the indicator LED long on 3
seconds, otherwise the system will restart and then into and network inclusion status.
Fig.1
ZIGBEE NETWORK INCLUSION
1) Connect the power supply (1 pc CR2450 button battery).
2) Press the Reset button for 2 seconds until see green LED blinking fast (Refer to the above
steps).
3) Choose "FBee" to enter the Network Inclusion mode on the APP, then click " ".
4) When prompt a message “Request Access Success”, please go to the device list interface, and
refresh the device list, the device will be displayed.
Installation Instructions
DETECTING RANGE
Reset button

HIOTH User Manual
HIOTH TECHNOLOGY CO.,LTD.
A. DetectingAngle: 110 degrees
B. Installation Height: 2.1 m
C. Detecting Distance: 9-12 m
Fig.2
INSTALLATION TIPS
Fig.3

HIOTH User Manual
HIOTH TECHNOLOGY CO.,LTD.
INSTALLATION STEPS
1. Ensure that the system properly powered
Removing the Mylar film to make device on power. Device will in warm-up state when red
LED flashes, after 30 seconds LED off, warm-up complete.
Factory default built in a CR2450 battery inside the detector and used a Mylar film to isolate
batteries from electric circuit of the detector. Remove the battery Mylar film when ready to
let the detector work.
If there is no battery inside the detector or need to replace a new battery, please insert the
battery first.
Fig.4
2. Paste device in the area required after removing double-side tap on the back side.
Fig.5
3. Note: Please keep arrow part in the picture upwards. Put the detector into the bracket.

HIOTH User Manual
HIOTH TECHNOLOGY CO.,LTD.
Fig.6
Safety Notice
This device is a wireless communication product, please do not place the device to work in
the metal container, in case the signal is blocked.
The working temperature is -10°C to +50°C.
Keep the device away from a strong sunlight, humidity, high temperature or mechanical
shock.
Keep the device away from acid-base and other corrosive solids, liquids, gases, to avoid
damage.