HiRO H50226 User manual

H50226/H50227
5/8 Port 10/100/1000 Mbps
Fast Ethernet Gigabit LAN Switch
+1909.595.80.86
[email protected] [email protected] www.hiroinc.com
All ports can be used as an uplink port for connecting to another unit without using
crossover cable. When using the uplink port, you can extend the distance to 100m for
linking another switch or hub.
Never stack more then eight units if freestanding
Do not place objects on top of any unit or stack
Do not obstruct any vents at the sides of the case
* Use only the power adapter which is provided with the switch to prevent damage to
the unit.
Uplink
To prolong the operational life of your units
This product comes with 1 yr Warranty. For further details about warranty policy
and Product Registration, please visit support section of www.hiroinc.com
www.hiroinc.com
Quick Installation Guide

FCC Warning
This equipment has been tested and found to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC Rules. These limitations are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
Measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into a different outlet from that the receiver is connected.
Consult your local distributors or an experienced radio/TV technician for help.
Shielded interface cables must be used in order to comply with emission limits
Changes or modifications to the equipment, which are not approved by the party
responsible for compliance could affect the user's authority to operate the equipment.
Copyright _ 2013. All Rights Reserved.
Company has an on-going policy of upgrading its products and it may be possible that
information in this document is not up-to-date.
Please check with your local distributors for the latest information.
No part of this document can be copied or reproduced in any form without written consent
from the company.
Trademarks:
HiRO is a registered trademark of HiroInc. All other trademarks are the property of the
respective manufacturers.
General Description
The H50226/7 is a 10/100/1000Mbps Desktop Ethernet unmanaged switch designed
to enhance network performance in a compact form factor.It can also be mounted
vertically using the stand provided along with the switch.The switch comes with 5/8x
10/100/1000Mbps ports, offering solutions for accelerating bandwidth needs of small
Ethernet workgroups. The switch uses store and forward packet-switching technology
which offers reliable data transfer and supports automatic MDI/MDI-X detection & auto
crossover for uplink ports which eliminates the need for cross over cables or dedicated
uplink ports. Any port can simply plug to a server or a switch, using the usual straight
throughtwisted pair cable. This switch is ideal for network connectivity for the SOHO
environment.
Product Features
5/8 RJ-45 Ports for 10BaseT, 100BaseTX & 1000BaseT connectivity
Complies with IEEE802.3, IEEE802.3u, IEEE802.3ab standards
Supports IEEE802.3 Nway auto-negotiation protocol
Supports IEEE 802.3x Full-duplex Flow Control
Supports IEEE802.1p priority tag based QoS
Supports MDI/MDI-X auto crossover for each port
Supports wire speed packet filtering and forwarding rate
Supports store-and-forward switching architecture
Link & activity indicators for each port
Energy Efficient
FCC Class B, CE
External Power Adapter
* If any of the items is damaged or missing, please contact your retailer immediately
.
Package Contents
H50226/7 5/8 port 10/100/1000Mbps Desktop Ethernet Switch
5V DC, 1A Switching power adapter
Quick installation guide
Rear View
Front View
After installing the switch, you can check its status from the LED indicators on the front
panel shown below. .
LED Color Status
Power (P) Blue On
Off
Link / ACT Blue On
Blinking
Indication
The switch is power on
The switch is power off
A link is established
A link is established and Data
is being transmitted and received
Plug the circle end of the power adapter firmly into the power port on the switch rear panel,
and the other end into an electric service outlet, then the device is ready to use.
Power Connection
Ports 1 - 5/8 :The switch has five/eight10/100/1000Mbps RJ-45 ports where you can
connectcomputers or network devices to the switch.
DC-IN : This port connects to the power adapter.
.
The switch features auto-MDI/MDIX crossover detection function and provides plug-and-
play capability. Users can immediately use any of the features of this product simply by
plugging the network cables (RJ-45) into the computers and the switch.
Connecting Computers to the Switch
(Ports 1-8)
12345678