Hisense 49BM66AE User manual

USER MANUAL
49” / 55”M SERIES
RSAG2.025.7065SS E English
Read the manual carefully and ensure you have fully understood its contents
before operating this device for the rst time

www.hisense-b2b.com
2
49_55BM66AE User Manual
Declaration
Any content and service accessed through this device, while only intended for individual noncommercial
use, shall be the property of the applicable third party and subject to protection by regulations and laws
on copyright, patent, trademark and other intellectual property rights. No part of such content and service
may be modied, duplicated, published, uploaded, distributed, translated, marketed, or used to make and
distribute products derived from it without the prior permission of the content owner or service provider.
You acknowledge and agree explicitly that you will solely bear the risk associated with the use of this
device, and further you will solely bear any risk related to satisfactory quality, performance and accuracy
for any content and service accessed through this device. To the maximum extent permitted by applicable
law, this device and any third party’s content and service is provided as it is without any guarantee, express
or implied.
Manufacturer hereby declare explicitly that Manufacturer shall not be held liable for any guarantee and
conditions, express or implied, related to this device and any content and service, including but not limited
to warranty on marketability, satisfactory quality, tness for a particular purpose, accuracy, quiet use and
non-violation of any third party’s rights; to the maximum extent permitted by applicable law, Manufacturer
gives no guarantee on the accuracy, validity, timeliness, legitimacy and completeness of any content or
service provided through this device, or the tness of such device, content or service for your particular
requirement, or the protection from interruption and error during operation of such device, content or service;
to the maximum extent permitted by applicable law, in any case, including fault or neglect, Manufacturer
shall not be held liable for legal actions or indemnity obligation arising from any consequence as a result of
or related to any information loaded in this device or use of such device, content or service by you or any
third party .
Any content and service provided as it is together with this device shall be the property of the applicable third
party, therefore Manufacturer gives no declaration or warranty on modication, suspension, cancellation,
termination or abortion thereof, and shall not be held liable for legal actions or indemnity obligation arising
thereof.
Manufacturer reserves the rights to restrict the use or access of certain content or service. As the content and
service are transmitted through third party’s network and transmission facilities, Manufacturer undertakes
no customer service thereof or the obligation for such customer service.
Statement
• The pictures and instructions in this user manual are for reference only, and may be different from the
actual product. Please subject to the actual product. {This statement is throughout this User Manual)
• Quality upgrades, product design and specications are subject to change without notice.
• The software content service applicable to this product depends on the third party provider, and some
software may not be used due to network, region, service cycle and other problems, which has nothing
to do with the product quality. Please contact the third party provider for relevant details.

www.hisense-b2b.com 3
49_55BM66AE User Manual
Important Safety Precautions
Do not open the back cover.
In no case the user is allowed to operate
inside the device.
Only a qualied technician is entitled to
operate.
This symbol alerts user about the .A&.
presence of a dangerous voltage not isolated
inside the product which can be sufciently
powerful to constitute a risk of electrocution.
This symbol alerts user about the JIil
presence of important operating instructions
and maintenance in the document enclosed
in the package.
AC voltage: This symbol indicates that the rated voltage marked with the symbol is AC voltage.
DC voltage: This symbol indicates that the rated voltage marked with the symbol is DC voltage.
Class I product: This symbol indicates that it requires a safety connection of protective earthing
(ground).
Disposal of Used Electrical & Electronic Equipment
Packaging and electrical goods should be recycled appropriately, and not treated as household
waste. Please dispose of this equipment at your applicable collection point for the recycling of
electrical & electronic equipment waste. By ensuring the correct disposal of this product, you
will help prevent potentially hazardous to the environment and to human health, which could
otherwise be caused by unsuitable waste handling of this product. The recycling of materials
will help conserve natural resources. Please do not therefore dispose of your old electrical
and electronic equipment with your household waste. For more detailed information about
recycling of this product, please contact your local city ofce, your household waste disposal
service or the shop where you purchased the product.

www.hisense-b2b.com
4
49_55BM66AE User Manual
Safeguards
Please read the following safeguards for your device and retain for future reference. Always follow all warn-
ings and instructions marked on the device.
01. A note about safety and operating instructions
Read and follow all safety and operating instructions, and retain them safely for future reference.
02. Heed Warnings
Adhere to all warnings on the appliance and in the operating instructions.
03. Cleaning
Unplug the device from the wall outlet before cleaning. Do not use liquid, abrasive, or aerosol cleaners.
Cleaners can permanently damage the cabinet and screen. Use a lightly dampened cloth for cleaning.
04. Water and Moisture
Avoid dripping or splashing of liquids onto the product. Objects lled with liquids, such as vases, should
not be placed on the product.
05. Ventilation
Slots and openings in the cabinet are provided for ventilation, to ensure reliable operation of the device
and to protect it from overheating. Do not cover the ventilation openings in the cabinet and never place
the set in a conned space such as built-in cabinet unless proper ventilation is provided. Leave a mini-
mum 10cm gap all around the unit.
06. Power Source
This device should be operated only from the type of power source indicated on the marking label. If you
are not sure of the type of power supplied to your home, consult your appliance dealer or local power
company.
07. Power-Cord Protection
Power- supply cords should be routed so that they are not likely to be walked on or pinched by items
placed upon or against them, paying particular attention to cords at plug, wall outlets, and the point where
they exit from the device. MAIN plug is used as the disconnect device, the disconnect device shall remain
readily operable.
08. Lightning
For added protection for this device during a lightning storm, or when it is left unattended and unused
for long periods of time, unplug it from the wall outlet and disconnect the cable system. This will prevent
damage to the device due to lightning or power-line surge.
09. Overloading
Do not overload wall outlets and extension cords as this can result in a risk of re or electric shock.
10. Object and Liquid Entry
Never push objects of any kind into this device through openings as they may touch dangerous voltage
points or short-out parts that could result in re or electric shock. Never spill liquid of any kind on or into
the device.

www.hisense-b2b.com 5
49_55BM66AE User Manual
11. Servicing
Do not attempt to service this device yourself as opening or removing covers may expose you to dan-
gerous
12. Damage Requiring Service
Unplug the device from the wall outlet and refer servicing to qualied service personnel under the fol-
lowing conditions:
(a) When the power - supply cord or plug is damaged.
(b) If liquid has been spilled, or objects have fallen into the device.
(c) If the device has been exposed to rain or water.
(d) If the device does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions as an improper adjustment of other controls
may result in damage and will often require extensive work by a qualied technician to restore the
device to its normal operation.
(e) If the device has been dropped or the cabinet has been damaged.
(f) When the device exhibits a distinct change in performance - this indicates a need for service.
13. Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts spec-
ied by the manufacturer or have the same characteristics as the original part. Unauthorized substitu-
tions may result in re, electric shock or other hazards.
14. Safety Check
Upon completion of any service or repair to the device, ask the service technician to perform safety-
checks to determine that the device is in safe operating condition.
15. Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or
other products (including ampliers) that produce heat.
16. Fire
The product should be situated away from naked ame sources such as lighted candle.
17. Off-gassing
The device smells of plastic is normal and will dissipate over time.
A Incorrect replacement of the battery may lead to the risk, including the replacement of another
similar or the same type. Do not expose batteries to heat such as sun or re or something like that.
The device should not be exposed to dripping and spraying and it cannot be placed under
objects lled with liquids.
A Main plug is used as the disconnect device, the disconnect device shall remain ready for
operating.
A Main plug is used as the disconnect device, the disconnect device shall remain ready for a
protective earthing connection.

www.hisense-b2b.com
6
49_55BM66AE User Manual
Start Guide
Precautions for Installation
1. As shown in the gure below, leave a ventilation space around the device.
2. Do not install the device as shown below.
Insufficient ventilation will overheat the device and may
cause damage to the device and even fire.
Hinder air circulation
When mounted on the wall:
Please leave this space
around the device

www.hisense-b2b.com 7
49_55BM66AE User Manual
Contents
Contents ..................................................................................................................... 1
Accessories List ........................................................................................................... 2
Wall Mount (Optional) ............................................................................................... 2
Remote Control .......................................................................................................... 5
Control Panel .............................................................................................................. 7
Terminal Introduction ................................................................................................. 8
Initial Startup ............................................................................................................. 10
System Menu ........................................................................................................... 11
Serial Protocol ........................................................................................................... 12
Specifications ........................................................................................................... 16
EU Declaration of Comformity (DoC) .................................................................... 18
Miscellaneous .......................................................................................................... 15

www.hisense-b2b.com
8
49_55BM66AE User Manual
Accessories List
Wall Mount (Optional)
1
2
Remote Control x 1
User Manual of the Device x 1
Battery x 2
Energy Efciency x 1
Power Cord x 4
Logo Bracket x 1
1. Before installing the wall-mount bracket, rst place the machine on a secure and clean desktop with soft
protective cloth. Conrm that the desktop is solid and reliable since the machine is heavy.
2. Remove the wall-mount screws in the wall-mount holes of the rear shell. (Ignore this step in the absence
of wall-mount screws. )
3. To avoid damage of the machine, please install the wall mount strictly in the sequence of rollers, wall-
mount bracket and wall-mount screws.
4. Before hanging the machine, please conrm that the wall-mount bracket is installed securely without
looseness.
5. This product can be both used in horizontal mode and vertical mode. The horizontal installation is shown
in Figure 1, and the vertical installation state is shown in Figure 2.
Model VESA wall mount
standard (mm)
Diameter of wallmount
screw (mm)
Panel 300 x 300 M6
Warning
• At the four wall-mounting positions shown in the gure, the screw installation depth H should be 6-10mm
from the bottom of sunken pit in the rear shell.
• The vertical installation shall be performed as shown in Figure 2. The screen can not be turned upside
down.

www.hisense-b2b.com 9
49_55BM66AE User Manual
Figure 1: Horizontal installation
Figure 2: Verticle installation

www.hisense-b2b.com
10
49_55BM66AE User Manual
Rear shell
Cushion block
Screw
LCD screen
[Note]
• Only the installation specication of the wall mount is described here; the appearance of rear shell is
for schematic purpose only.
• The screw installation depth in the wall-mount holes of the rear shell is 6-10mm; overlong screws will
cause irreparable damage to the equipment.
• If the intactness of the machine cannot be guaranteed during wall mounting, please contact professional
installation personnel or technical support personnel.
• This wall mount is suitable for concrete and brick walls. For plank and plasterboard walls, special
reinforcement is required instead of directly using the wall mount. Ensure that a single expansion bolt
xed in the wall can bear over 1 /3 of the overall weight of the machine.

www.hisense-b2b.com 11
49_55BM66AE User Manual
Mute
Enter/exit mute mode
Standby
Enter/exit sleep mode
Unlock the remote control
Source
Select a source
Source
Select a source
Move the focus left/right, etc.
Increase/decrease the
volume (+/-)
Setting
Open the Setting menu
OK
Conrm the operation
Menu
Open the function menu
Home
Enter the home page of
the machine
Remote Control3
Move the focus up/down, etc.
Note1When the remote control is locked, it can be unlocked by pressing the “UnlockOK - OK - Unlock”
keys in sequence.

www.hisense-b2b.com
12
49_55BM66AE User Manual
How to Replace Batteries
1. Separate the battery cover from the remote control device at the battery cover pivot to open the
battery cover.
2. Put in two 1.5V AAA alkaline batteries. Make sure to match the(+) and ( - ) ends of the batteries with
the(+) and ( - ) ends indicated in the battery compartment.
3. Push the battery cover back from the bottom up till it completely ts the remote control device.
Effective Range
1. Remote control distance: The remote control can work at a distance of up to 8 meters in front of the
T V.
2. Remote control angle: Taking the remote receiver on the TV as an apex, 6 meters away, its controlled
horizontal angle is within ±30°, while the vertical angle is within ±15 °.
Precautions
1. If the remote control works abnormally or unstably, or cannot remotely control the machine, please
replace the batteries.
2. If the remote control is to be left unused for a long period of time or the batteries have run out, please
take the batteries out. (Please dispose of waste and used batteries properly as such batteries can
cause environmental pollution.)
2. To achieve the optimal remote control reception effect, please align the remote transmitter of the
remote control with the remote receiver on the machine.

www.hisense-b2b.com 13
49_55BM66AE User Manual
Control Panel4
Name / Operation Function
Remote receiver Receive signals transmitted by the remote control via this window.
Indicator When the machine is on, the indicator light is blue; when it enters
sleep mode, the indicator light is red.
Logo bracketRemote receiver/indicator
[Note]
• The appearance is subject to the actual product.
•Since power outage and system processing takes some time, DO NOT power on and off the machine
in rapid succession; otherwise the machine may work abnormally.

www.hisense-b2b.com
14
49_55BM66AE User Manual
Terminal Introduction5
Name / Operation Function
Remote receiver Receive signals transmitted by the remote control via this window.
Indicator When the machine is on, the indicator light is blue; when it enters
sleep mode, the indicator light is red.
Logo bracketRemote receiver/indicator
[Note]
• The appearance is subject to the actual product.
• Since power outage and system processing takes some time, DO NOT power on and off the machine
in rapid succession; otherwise the machine may work abnormally.

www.hisense-b2b.com 15
49_55BM66AE User Manual
[Note]
• The rear view is for reference only, please subject to the actual product.
• RS232 port: It is for serial communication control of the machine.
• It is possible that some external devices cannot be connected to the machine due to individual
difference. In such case, please replace the signal line with a suitable one or add an adapter cable
matching the port.

www.hisense-b2b.com
16
49_55BM66AE User Manual
Name / Operation Function
USB USB standard port is provided with this machine; it can also be used to connect a stan-
dard USB2.0 or USB3.0 device, such as hard disk drive and USB ash drive.
HDMI It can be used to connect an external device with HDMI port, such as STB, player, or
PC with HDMI output.
Network Port It can be used to connect a network cable so as to access the Internet.
VGA It can be used to connect a PC or other external device with a VGA port.
RS232/IR OUT It is the output port of the serial communication command.
RS232/IR IN It is the input port of the serial communication command.
Headset It can be used to connect a headset.
LINE IN Input VGA audio analog signals
DVI OUT When DVI or DP has signal input, DVI OUT can output DVI or DP input signals; it can
be used to connect other display device with DVI port.
DVI IN It can be used to connect an external device with DVI, or connect a device with HDMI
port via HDMI-DVI adapter.
DP It can be used to connect an external device with DP port.
[Note]
• The rear view is for reference only, subject to the actual product.
• It is possible that some external devices cannot be connected to the machine due to individual difference.
In such case, please replace the signal line with a suitable one or add an adapter cable matching the port.

www.hisense-b2b.com 17
49_55BM66AE User Manual
1. Startup/Shutdown
• Connect the power cord of the machine to a 100-240V AC power outlet.
• Gently press the power switch I o of the machine toward I to turn on the machine.
•In power-on state, press the STANDBY key c!) on the remote control; the machine will enter sleep
mode. To watch normally, simply press again the STANDBY key c!) on the remote control.
• To shut down the machine, press the power switch I o again toward o.
2. Adjust Local Settings
•Use of the setting function can satisfy your different needs and allow you to fully enjoy the audiovi-
sual effect brought by the machine.
•You can adjust image and sound, set network connection and perform other operations from here.
• In menus at different levels, you can perform the following operations using the remote control:
Press the arrow keys to select each option
Press the OK key to conrm operation or enter the sub-menu
Press the LEFT/RIGHT key to adjust values
Press the UP/DOWN key to adjust options
•Press the key to go back to the previous menu.
Initial Startup6
[Note]
•After shutdown under AC power supply, there should be an interval of at least 5s before restart to prevent
abnormality of the machine.

www.hisense-b2b.com
18
49_55BM66AE User Manual
System Menu7
1. To open the System menu:
Press the SETTING key to enter the Setting interface, then select the System menu.
2. Menu introduction:
•Time Settings: Set the local time.
•Language: The default language is Chinese. The menu display language can be switched between
Chinese and English.
•Fast Standby: The default state is OFF. When it is OFF, the machine will enter standby normally;
when it is ON, both the screen and the sound will be turned off when the machine enters standby.
•Multi Screen Display: Multi-screen splicing display can be realized by setting splicing row and
column values matching the actual condition according to horizontal and vertical ratios; positions
can be set from left to right and from up to down.
•ID Set: Set the machine ID between 1-255.
•Timer Switch: Set the time when the machine can be powered on/off automatically.
•Change BootLogo: Options include OFF, Default and Custom. When Custom is selected, the
Logo picture should be placed under the Logo directory in the USB ash drive. The Logo picture
should be in png or jpg format, with the resolution not less than 192Qx1080.
•Change BootAnimation Video: Options include OFF, Default and Custom. When Custom is
selected, the boot animation or material should be placed under the root directory in the USB ash
drive. The boot animation should meet the format of Android boot animation; the boot video should
be in mp4 format, and its size should be less than 20M. As for the naming convention for boot
animation/video, there will be prompt messages when the USB ash drive is inserted.
•Change NoSignal Logo: Select a picture for change; the system will give a prompt after change.
•The screensaver logo picture for change should be placed under the logo directory in the USB ash
drive.
• The logo picture should be in bmp, jpg or png format.
•HDMI Version: Select the HDMI version: HDMI 1.4 or HDMI 2.0. [Note] Available only under OPS
and HDMI channels.
•Lock Native Key: The default state is OFF. When it is OFF, the keys on the machine will not be
locked; when it is ON, the keys will be locked.
•Serial Status: Show the current state of serial port.
•Remote Password: The default state is OFF. When it is OFF, the remote control will not be shielded;
when it is ON, the remote control can be used only after the correct password is input.
•Net Start System: The default state is OFF. When it is OFF, the machine cannot be woken up;
when it is ON, the machine can be woken up via network.

www.hisense-b2b.com 19
49_55BM66AE User Manual
Serial Protocol8
Serial Port State: When the serial port is open, the machine can receive serial port commands sent by the
external controller. See the table below for the specic command protocol:
1 Baud rate: 9600 2 Control part: PC→ TV 3 Response part: TV→PC
Protocol
Header Length Command Code BoardlD Data Check Protocol End Remark
Source
Selection
DP
PC to
TV DD FF 00 07 C1 08 00 00 XX 16 XX BB CC
Under Data, the rst XX is
the equipment number; the
second XX is the check
digit
TV to
PC AB AB 00 07 C1 08 00 00 XX 16 XX CD CD
VGA
PC to
TV DD FF 00 07 C1 08 00 00 XX 17 XX BB CC
TV to
PC AB AB 00 07 C1 08 00 00 XX 17 XX CD CD
HDMI
PC to
TV DD FF 00 07 C1 08 00 00 XX 08 XX BB CC
TV to
PC AB AB 00 07 C1 08 00 00 XX 08 XX CD CD
DVI
PC to
TV DD FF 00 07 C1 08 00 00 XX 09 XX BB CC
TV to
PC AB AB 00 07 C1 08 00 00 XX 09 XX CD CD
ON/OFF
OFF, PC to TV DD FF 00 08 C1 15 00 00 XX AA AA XX BB CC
TV to PC AB AB 00 08 C1 15 00 00 XX AA AA XX CD CD
ON, PC to TV DD FF 00 08 C1 15 00 00 XX BB BB XX BB CC
TV to PC AB AB 00 08 C1 15 00 00 XX BB BB XX CD CD
Mute
Control
OFF, PC to TV DD FF 00 07 C1 26 00 00 XX 00 XX BB CC
TV to PC AB AB 00 07 C1 26 00 00 XX 00 XX CD CD
ON, PC to TV DD FF 00 07 C1 26 00 00 XX 01 XX BB CC
TV to PC AB AB 00 07 C1 26 00 00 XX 01 XX CD CD

www.hisense-b2b.com
20
49_55BM66AE User Manual
Set
Volume
PC to TV DD FF 00 07 C1 27 00 00 XX XX XX BB CC
Under Data, the rst XX is
the equipment number; the
second XX is the set
volume; the third XX is the
check digit
TV to PC AB AB 00 07 C1 27 00 00 XX XX XX CD CD
Query
Function
PC to TV DD FF 00 06 C1 28 00 00 XX XX BB CC
Under Data, the rst XX is
the equipment number; the
second XX is the check
digit
TV to PC AB AB 00 0C C1 28 00 00 XX XX XX XX XX XX XX XX CD CD
Under data, the rst XX is
the equipment number, the
second XX is the value of
volume (valid in power-on
state); the third XX and the
fourth XX together repre-
sent the current source (05
02--DVI; 05 03--DP; 05 04
-HDMI; 08 01-VGA; valid in
power-on state); the fth
XX represents the pow-
er-on/off state (00 is the
power-on state; FF is the
power- off state); the sixth
XX represents the mute
state (01 is the muted state;
00 is the unmuted state;
valid in power-on state);
the seventh XX represents
the signal presence/
absence state (00 means
signal is absent; 01 means
signal is present, valid in
power-on state); the eighth
XX is the check digit