Hitachi CM1721ME User manual

Tt5CC-l
!=I G
Colour Monitor
CM1721ME User Manual
BEDIENUNGSANLEITUNG
17MVX-v2
For future references, record the serial number of your
display monitor, SERIAL No.
The serial number is located on the rear of the monitor.
READ THE INSTRUCTION INSIDE CAREFULLY.
KEEP THIS USER MANUAL FOR FUTURE REFERENCES
This monitor is Energy Star compliant when used with
a computer equipped with VESA DPMS.

For U.K. Customers
THIS PRODUCT IS SUPPLIED WITH ATWO PIN MINS
PLUG FOR USE IN MAINLAND EUROPE. FOR THE U.K.
PLEASE REFER TO THE NOTES ON THIS PAGE.
NOTE:
ELECTRICAL CONNECTIION
Your monitor requires an electrical supply of 240 volts - 50 Hertz
and should be protected by a 5 amp fuse. Your equipment is
supplied with a plug incorporating a 5 amp fuse fitted to the mains
lead. If the plug that is fitted to the equipment is not suitable for
your socket outlet, it must be cut off and the appropriate plug fitted.
The cut off plug should be disposed of, do not insert it into a 13
amp socket to prevent the hazard of electric shocks. With plugs not
incorporating a fuse, the circuit must be protected by a 5 amp fuse.
WARNING: THIS EQUIPMENT MUST BE EARTHED.
IMPORTANT
Your equipment is supplied with a mains lead, the wires of which
are coloured in accordance with the following code: Green and
Yellow-Earth, Blue-Neutral, Brown-Live.
Green & Yellow
to Earth
Blue to Neutral
Brown to Live
Fuse
Cord Clamp
-I-

As the colours of the wires in your mains lead in this equipment
may not correspond with the markings identified with the terminals
of your plug. proceed as follows:
The wire which is coloured Green and Yellow must be connected to
the terminal in the plug which is marked with the letter E or by the
symbol or coloured Green or Green and Yellon,
The wire which is coloured Brown must be connected to the
terminal which is marked with the letter L or coloured Red.
The wire which is coloured Blue must be connected to the terminal
which is marked N or colourcd Black
The plug moulded on to the cord incorporates a fuse. For
replacement, use a 5 amp BS 1362 fuse. Only ASTA approved
fuses should be used. The fuse cover/carrier must be refitted when
changing the fuse. In the event of losing the fuse cover/carrier, the
plug must not be used until a replacement has been obtained from
your nearest electrical stockist and fitted. The colour of the fuse
cover/carrier is that of the coloured marks on the insert in the base
of the plug.
- II -

Please read the following instructions carefully to prevent
potential hazards. This manual should be retained for future use.
1. Do not expose the monitor to rain, water, moisture, or direct
sunlight.
2. Do not spill liquid into the monitor
3. Do not insert any objects into the monitor cabinet’s openings.
4. Do not place near or above sources of heat such as heaters or
radiators.
5. Do not block or cover ventilation opening with any material.
The openings and slots on the cabinet provide necessary air
flow for heat dissipation. The unit should never be enclosed
or built upon unless adequate ventilation is provided.
6. Do not remove the cover to try to service this unit.
Servicing
of any nature should only be performed by authorized service
personnel.
7. WARNING! Do not attempt to service this unit yourself as
opening or removing covers may expose you to dangerous
voltage or other hazards.
8. The On/Off switch is not a disconnecting device. Make sure
to remove the AC power cord after using.
9. When the monitor is turned on continuously for a long period,
the phosphors of the CRT face plate may “bum” leaving a
permanent image on the screen. In order to preserve CRT life,
be sure to turn off the monitor or decrease the displayed
intensity when not in use.
- III -

10. WARNING! The voltage ratings and the rated frequencies
are posted on the back panel of this product. Please see
the
overlay in the center of the back panel of this product.
NEVER connect to any other voltage or frequency. Follow
ALL warnings and instructions marked on the product.
11. This, product is equipped with a 3-wire grounding-type plug.
It will only fit into a grounding-type power outlet. This is a
safety feature. If you are unable to insert the plug into the
outlet, the outlet can be replaced by an electrician. Do not
defeat the safety purpose of the grounding-type plug by
improper use or alteration.
12. Power source
. This monitor is able to operate using power sources from
108-264VAC/60-50Hz by means of internal auto power
switching.
. For 120V operation, use only with power cord having a
parallel blade grounding-type plug, rated at I OA- 125V.
. For 240V operation, use only with power cord having a
tandem blade grounding-type plug rated 1 OA-250V
minimum.
- IV -

Bitte lesen Sie diese Sicherheitshinweise sorgftitig durch,
damit die richtige Verwendung des Gerstes sichergestellt wird.
Diese Anleitung sorg&ltig aufbewahren.
1. Das Bildschirmger~t nicht Regen, Wasser, Feuchtigkeit oder
direktem Sonnenlicht aussetzen.
2. Keine Fltissigkeiten tiber dem Bildschirmgerat Verschtitten.
3. Niemals Gegenstande durch die &fnungen in das Innere des
Gerates stecken oder hineinfallen lassen.
4. Das BildschirmgeCit nicht in der Nahe von Heizgeraten der
Heizungen aufstellen.
5. Nicht die beliiftungsdffhungen des Gehauses blockieren oder
abdecken. Diese @frrungen und Schlitze im Gehause sorgen
tir die notwendige Ventilation. Das Bildschirmgerat sollte
niemals mit einer Verkleidung umgeben oder in einem Regal
eingebaut werden. falls keine ausreichende
Beltiftung
vorhanden ist
6. Niemals versuchen, das Gehause zu entfemen oder das
Bildschirmgerat selber zu war-ten.
Alle Wartungsarbeiten
sollten nur vom Kundendienst durchgefiihrt werden.
7. Nicht versuchen, das Bildschirmgerat selbst zu war-ten. Im
Inneren des Gerates sind gef&rliche elektrische Spannungen
und andere Gefahren vorhanden.
8. Der Netzschalter ist keine Trennvorrichtung Sicherstellen, daR
die NetzanschluRleitung, wenn das Gerat Iangere Zeit nicht
benutzt wird, aus der netzsteckdose gezongen wird.
-V-

9. Bei Einstellung des Bildschinngerates auf starkste Helligkeit
und Kontrast uber langere Zeit Konnen die Leuchtschicht der
Bildrohrenoberfhiche einbrennen. Zur Verlangerung der
Lebensdauer der Bildrohre ist sicherzustellen, dal3 das
Bildschirmgerat nach der Verwendung ausgeschaltet wird
oder Helligkeit und Kontrast verringert werden.
10. Die Angaben zur Spannung und Frequenz entnehmen Sie dem
Fabrikschild.
Schliessen Sie Ihr Gerat nie an eine
Stromquelle mit andeier. als der dort genannten Spannung/
Frequenz an. Beachten Sie ausserdem alle am Gerat
angebrachten Warn- und Bedienungshinweise.
11. Ihr Gerat ist mit einem dreipoligen Schukostecker ausgestattet.
Dieser Stecker kann nur an eine Schutzkontaktsteckdose
angeschlossen wrerden.
Sollte der Stecker nicht in die
Steckdose passen, lassen Sie diese bitte von einem Elektriker
auswechseln.
Es mu8 sichergestellt werden.
dal3 die minimale
Bildwiederholfrequenz von
70 Hz bei Positivdarstellung
und 60 Hz bei Negativdarstellung
nicht unterschritten wird (storendes Bildschirmflimmem konnte
die Folge sein).
Weiterhin wird aus ergonomischen Griinden empfohlen, die
Grundfarben Blau und Rot nicht auf dunklem Untergrund zu
verwenden (schlechte Lesbarkeit und erhohte Augenbelastung bei
zu geringem Zeichenkontrast w&ren die Folge).
“Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil
1000 betragt 70dB(A) oder weniger”
- VI -

(Gerat, Typ, Bezeichnung)
in ijbereinstimmung mit den Bestimmungen der BMPT-Amt-
sblVfg 243/l 99 1 funk-entstort ist. Der
vorschriftsmai3ige Betrieb
mancher Gerate (zB Me&sender) kann allerdings gewissen Ems&r
ankungen unterliegen.
Beachten Sie deshalb die Hinweise in der Bedienungsanleitung.
Dem Bundesamt’ fur Zulassungen in der Telekommunikation
wurde das inverkehrbringen dieses Gerates angezeigt und die
Berechtigung zur ijberprtifung der Serie auf die Einhaltung der
Bestimmungen eingeraumt.
- VII -

/
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation.
This equipment generates. uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions. may
cause harmful interference to radio
communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for
help.
Warning:
A shielded-type power cord is required in order to meet FCC
emission limits and also to prevent interference to the nearby radio
and television reception. It is essential that only the supplied
power cord be used.
Use only shielded cables to connect l/O devices to this
equipment.
You are cautioned that changes or modifications not
expressly approved by the party responsible for compliance could
void your authority to operate the equipment.
- VIII -