Hitachi Travelstar C4K60 User manual

Page 1 version 1.0
Quick installation guide
Hitachi Travelstar C4K60
Models: HTC426030G7CE00
HTC426020G7CE00
HTC426060G9AT00
HTC426040G9AT00
HTC426030G7AT00
HTC426020G7AT00
Handling precautions
ySet the drive down gently to prevent damage from impact or vibration.
yHandle the drive carefully by the edges. Do not touch the exposed printed circuit board or any electronic components.
yDo not press on the top or bottom of the drive.
yBefore handling the drive, discharge any static electricity from yourself and your clothing. With one hand touch an
unpainted metal surface, then touch the ESD bag with the other hand. Remain in contact with the chassis and the bag for a
minimum of two seconds.
yVibration, shock and static electricity to the drive will damage the precision parts. In particular, prevent vibration or shock
generated by dropping, knocking over or hitting the drive. Also, avoid touching the electrical components directly, which
can discharge electrostatic energy and damage the drive.

Hitachi Global Storage Technologies
Page 2 version 1.0
Mounting Instructions
Caution:Mount the hard drive according to the following instructions to ensure optimal performance.
•Mount the hard drive with M2.0 screws (screw engagement of 2.3mm max). Be careful not to add any
distorting force to the hard drive when mounting.
•Use either the bottom or side screw holes to secure drive. Do not attempt to use both bottom and side
screw holes simultanesly.
•The torque for fixing the screws is 2.5±05kgcm(2.2±0.4 lb. inch).
•The temperature of the center of the hard drive cover should remain less than 65°C at all times.
•The inertia of the chassis around the Z-axis of the gravity center of the device must be more than 3 x
10-4kg m2.
•In case of general Sub-notebook PC weight (1.7kg), the inertia of the chassis around the Z-axis of the
gravity center of the device is greater than 100 x 10-4 kg m2. Therefore, the required inertia level does
not conflict with the general electronic equipment.
•If installing the C4K60 next to a steel plate, the cover of the C4K60 and the steel plate must have at
least 2mm of space between them. This is necessary for air flow and cooling requirements.
•The PCBA side of the drive should be covered with insulation if it is in contact with any metal part of
the host system. Contact between the PCBA and metal may result in drive failure.

Hitachi Global Storage Technologies
Page 3 version 1.0
Mounting Recommendations
•Do not push on the striped area marked in the above image. Pressure on the striped area could cause contact between
the cover and movable parts inside the hard drive.
•Do not put a steel plate over the ‘Red Box’ area marked in the above image. If using a steel plate on the hard drive
cover side, 2mm of space is required between the plate and the drive to ensure airflow.
•The blue dotted lines in the above image represent the area in which shock drop insulation should be applied.
•The blue frame shown below represents the casing used if the drive can not be secured with screws.
•Hitachi Global Storage Technologies will assist customers with mounting design.

Hitachi Global Storage Technologies
Page 4 version 1.0
Recommended drop shock material distrubutors
http://www.sorbothane.com/distributor_beta.html
http://www.earsc.com/
Mounting Solution Company: E-A-R

Hitachi Global Storage Technologies
Page 5 version 1.0
© Copyright Hitachi Global Storage Technologies
Hitachi Global Storage Technologies
5600 Cottle Road
San Jose, CA 95193
Produced in the United States
2/05
All rights reserved TravelstarTM is a trademark of
Hitachi Global Storage Technologies.
Microsoft, Windows XP, and Windows are
trademarks of Microsoft Corporation in the United
States, other countries, or both.
Other product names are trademarks or registered
trademarks of their respective companies.
References in this publication to Hitachi Global
Storage Technologies products, programs or services
do not imply that Hitachi Global Storage
Technologies intends to make these available in all
countries in which Hitachi Global Storage
Technologies operates.
Product information is provided for information
purposes only and does not constitute a warranty.
Information is true as of the date of publication and is
subject to change. Actual results may vary.
This publication is for general guidance only.
Photographs may show design models.
07 February 2005