Hitachi Virtual Storage Platform G200 User manual

Hitachi Virtual Storage Platform
G200
Quick
Start
START
START
Prepare for
Installation
Connect the
Hardware
Power Up
the System
Enable Hi-Track
Remote Monitoring System
Run the Initial
Setup Wizard
Run the
Initial Startup
Wizard
Complete System
Setup
7
1
23
45
6
Quick
Start
Power, Fibre Channel,
iSCSI, and SAS
Cables (optional)
Software
Applications
Wrist
Strap
Storage
System
Bezel
Accessory
Box
1Prepare for Installation
LIFTING HAZARD
CAUTION
Lift with 3 people.
1. Unpack package contents
Disk Drives
Power
Distribution
Units
1
Rack
User-Supplied
Rack (if not
ordered from
Hitachi)
Additional
Cables
Management
Console PC
(with NIC)
2. Provide these
items
3. Install devices into
the rack
Uninterruptible
Power Supply (UPS)
(optional)
Install the service processor (SVP)
at the top of the rack, and the
storage system and drive tray(s)
at the bottom.
SVP
Switch
Storage
System
Drive Tray
HDS or User-Supplied Rack
101.4 lbs.
(46 kg )
Hitachi Virtual Storage Platform
G200
Quick
Start
START
START
Preparefor
Installation
Connect the
Hardware
PowerUp
the System
Enable Hi-Track
RemoteM onitoring System
Run the Initial
SetupWizard
Run the
Initial Startup
Wizard
CompleteSystem
Setup
7
1
23
45
6

Connect the Hardware
1. Connect expansion ports to drive trays
2
NOTE
If your network uses IP addresses 192.168.0.15-17,
do not connect to LAN1 until after you complete
the Initial Startup.
Storage
System
SVP
Controller 2Controller 1
RDY
AC IN
ALM
POWER LOCATE ALARM IN OUT
CONSOLE
RDY
AC IN
ALM
POWER LOCATE ALARM IN OUT
CONSOLE
RDY
AC IN
ALM
POWER LOCATE ALARM IN OUT
CONSOLE
RDY
AC IN
ALM
POWER LOCATE ALARM IN OUT
CONSOLE
RDY
AC IN
ALM
POWER LOCATE ALARM IN OUT
CONSOLE
RDY
AC IN
ALM
POWER LOCATE ALARM IN OUT
CONSOLE
Drive
Tray
Drive
Tray
Drive
Tray
Management
Console PC
Network
Switch
LAN3
Connected to user
LAN port on
Controller 1
LAN2LAN1
SVP
LAN4
Connected to user
LAN port on
Controller 2
SAS cable
Ports are color-coded for reference.
3. Make SVP connections
2. Connect user LAN ports to the SVP
Connect Controller 1 to LAN 3
on the SVP.
Connect Controller 2 to LAN 4
on the SVP.
Category 5 or
better Ethernet cable
Cables should lock into place.
Verify they do not pull out
without using the tab.
NOTE
If possible, use a UPS.
Power Up the System
3SVP (rear) 1. Plug in power to the SVP.
2. Power up the SVP before powering up the storage
system.
3. Connect the power cables to the rear panels on the
controllers and drive trays. For redundancy, connect the
power cables to feeds from separate power sources.
Confirm that the POWER LED on the front panel is on.
4. Attach the front bezel to the front of the storage
system, and then lock using the supplied key.
5. Press and hold the POWER ON/OFF switch on the
storage system for about 3 seconds. Wait for the READY
LED to change from amber to green (approximately
33 minutes).
SVP
(front)
RDY
AC IN
ALM
POWER LOCATE ALARM IN OUT
CONSOLE
RDY
AC IN
ALM
POWER LOCATE ALARM IN OUT
CONSOLE
Drive Tray (rear)
Storage System (rear)
Storage System (front)
POWER
READY
WARNING
ALARM
POWER
ON/OFF

Menu
Initial Setup Wizard
Power Management
System Management
Information
CTL1
Storage System
S/N: 410006
S/N: 400001
Maintenance Utility
Chassis
Install Remove Locate LED
Drives Alerts
Alert System Locked Logged in as user 00 Logout ?
Last Updated : 2015/02/23 20:32
Firmware
Alert Notifications
Licenses
Network Settings
D & Time
Audit Log Settings
Hardware
Administration
Storage System Storage System
Name
Contact
Location
Type
Storage System
Serial Number
03-xxxx-xxxx
Tokyo xxxx
HM800M
400001 25 degree C
Set up System Information
74 8 9 91
Data Spare Free Total
Number of Drives
IPv4 Address
IPv6 Address
CTL1
CTL2
CTL1
10.0.0.16
10.0.0.17
Temperature
CTL2
Controller Chassis
DB-00
Go to Detail
Go to Detail
TableGraphic
Run the Initial Startup Wizard
1. Congure the PC to use an IP address of 10.0.0.xxx, where
xxx = 1-99 or 101-254, and a subnet mask of 255.255.255.0.
2. Run Remote Desktop Connection:
Click Start > All Programs > Accessories >
Remote Desktop Connection.
In the Computer eld, type 10.0.0.100 and click
Connect.
On the Windows Security screen, type SVP-PC\SVP
in the top eld and raid-login in the bottom eld.
Click OK.
If prompted that the identity of the remote computer
cannot be veried, click Yes to continue.
3. In the Remote Desktop Connection window:
Click Start > All Programs > Hitachi Device
Manager - Storage Navigator.
Right-click Initial Startup and click Run as
administrator.
On the next screen, click Yes.
Click Start Setup at the bottom of the Initial Startup
screen.
When a message about checking the initial
environment appears, click OK.
4. Complete the Initial Startup elds.
5. Click Apply.
4
Cancel
Apply
Initial Startup
Default Account (maintenance)
Initial Startup Tool
New Password
Re-enter New Password
Network Setting
IPv4 Configuration:
IPv6 Configuration:
Storage System Address
CTL1:
CTL2:
Subnet Mask:
Default Gateway:
DNS Server 1:
DNS Server 2:
DNS Server 3:
Enable Disable
SVP Address
6. When Initial Startup is complete, click Close, and then click Confirm.
The SVP reboots automatically. Rebooting takes 5 to 10 minutes.
7. If you did not connect your IP network (switch) to the LAN1 port on
the SVP, do so now.
Run the Initial Setup Wizard
5
1. Repeat step 2 above to run Remote Desktop
Connection.
2. In the Remote Desktop Connection window,
click Start > All Programs > Hitachi Device
Manager-Storage Navigator >
StorageDeviceList.
3. In the Storage Device List window, click the icon
of the registered storage system.
4. If prompted about a security certicate, select
Continue to this website.
5. Log in to Device Manager - Storage Navigator.
6. From the Maintenance Utility menu, click
Hardware > Other hardware maintenance.
7. In the left pane of the Maintenance Utility
window, under Menu, click Initial Setup Wizard.
8. Provide the requested information in the System
Information and Date & Time pages, and then click
Apply and Next on each page.
9. At the Network Settings page, click Apply and
then Close.
10. In the left pane, click Administration > Alert
Notifications.
In the Alert Notications page, click Set Up.
In the Email tab, congure the notication settings.
In the SNMP tab, congure SNMP settings, and click
Apply.
To send a test email, click Send Test Email in the
Email tab.
11. In the left pane, click Administration > Licenses.
Under License Keys, click Install.
Enter the key code or specify the license key le.
Click Apply.
When the completion message appears, click OK.
Check the licenses you want to enable, and then click Enable
and Apply.
When the completion message appears, click OK.

Enable Hi-Track Remote Monitoring System
Hi-Track provides the remote monitoring and support functionality for Hitachi products. Hitachi
recommends you install and congure Hi-Track to monitor the storage system at the customer site.
For more information, download the Hi-Track documentation from the Hitachi Data Systems Support Portal:
https://portal.hds.com/
7Complete System Setup
Serial number locaon
7
6
3. Register your storage system
1. In a browser, type https://portal.hds.com.
2. Under Login, click Need to register?
3. Follow the on-screen instructions. When nished, log out of the Portal.
4. Log in to the Portal using the email address and the password sent by email.
5. Click My Products.
6. Conrm that your storage system appears under My Products. If not, click Register Additional Product and follow the
on-screen instructions.
7. At the Conrm Registration page, click Register.
8. Wait 15 minutes, and then click My Products and conrm that your storage system is registered.
Helpful links
Product documentation: https://portal.hds.com
Product interoperability: http://www.hds.com/products/interoperability
HDS Community: https://community.hds.com
Frequently asked questions: https://community.hds.com/groups/vsp-self-service
1. Make host connections
Congure the storage system host settings. Refer to the Hitachi Open-Systems Host Attachment Guide and the HDS Product Interopera-
bility Documentation at http://www.hds.com/products/interoperability.
Follow the instructions in your host, HBA, and NIC vendor documentation for information about host conguration.
Connect the Fibre Channel and iSCSI ports on the storage system to your network switch. Refer to the gures below and to your
switch documentation for details. Ports are color-coded for reference.
2. Record storage system serial number:
Fibre-Channel
cables
Hitachi Data Systems Corporaon 2015.
All rights reserved.
c
FE-94HM8031-00
Hitachi Virtual Storage Plaorm
G200 Quick Start