Hitron HT-EMN3 User manual

Model # HT-EMN3
WiFi Extender
Quick Install Guide

Hitron Technologies Americas2
Step 1: What’s in the Box
Look in the box and make sure you have the following:
Step 2: Locate your Gateway
If you have a pre-installed Hitron gateway, the gateway will
automatically setup your new HT-EMN3. When connected, the
AutoSync feature takes about 2 mins. (CODA Gateway pictured)
If you set up a HT-EMN3 with a non-Hitron gateway, the gateway might
not support auto-setup. Please read the manual and follow the
instructions.
Step 3: Choose a Method for AutoSync
The Hitron HT-EMN3 offers the ability to extend your home wireless
network through three possible media: Ethernet, MoCA or Wi-Fi.
Choose from the 4 following methodsfor AutoSync:
Method A: Ethernet setup
Method B: MoCA setup (coaxial cable)
Method C: Wi-Fi to Wi-Fi setup via Ethernet cable
Method D: Wi-Fi to Wi-Fi setup via WPS
HT-EMN3 WiFi Extender
Cat 6 Ethernet
Cable
Power Supply
Quick Install Guide
Gateway
HT-EMN3 WiFi Extender

Quick Install Guide - HT-EMN3 - WiFi Extender 3
Method A: Connect the HT-EMN3 with an Ethernet Cable
Use the Ethernet cable provided to connect the LAN port to one of the
LAN ports on the Hitron Gateway. (CODA Gateway pictured) Go to step 4
Method B: Connect the HT-EMN3 to a Cable Outlet (MoCA)
Use a coaxial cable (not included) to connect your HT-EMN3 CABLE
connector to a coaxial outlet. The coaxial outlet and your gateway must
be on the same coaxial network. Go to step 4
Method C: Wi-Fi to Wi-Fi Setup via Ethernet Cable
Use the Ethernet cable provided to connect the LAN port to one of the
LAN ports on the Hitron Gateway. (CODA Gateway pictured) Go to step 4
Gateway
HT-EMN3 WiFi Extender
Cat 6 Ethernet
Cable
Gateway
HT-EMN3 WiFi Extender
Cat 6 Ethernet
Cable
Coaxial Outlet
Coaxial Cable
(Not Included)
HT-EMN3 WiFi Extender

Hitron Technologies Americas4
Method D: Wi-Fi to Wi-Fi Setup via WPS
Use the power cord to connect the POWER port to a power outlet.
(see Step 4 picture)
1 Login to the gateway web page and turn on WPS.
2 Press the WPS button on the Gateway.
3 Press the WPS button on the back of the HT-EMN3. The HT-EMN3 WPS
LED will start blinking. WPS LED will become steady when active and
ready. Your HT-EMN3 is ready (don’t do Step 4). Go to step 4
Step 4: Connect HT-EMN3 to a Power Outlet
1 Ensure you are connected to gateway via method A, B or C
2 Use the power cord provided to connect the POWER port
to a power outlet.
3 AutoSync will start. Wait for 2 mins to complete setup. (WPS LED will
stop blinking green/red)
4 If you used Method C (WiFi to WiFi), unplug your HT-EMN3 (power and
Ethernet) and power it on at its final location.
Method D: Wi-Fi to Wi-Fi Setup via WPS
Gateway
HT-EMN3 WiFi Extender
Power Outlet
Power Cable
HT-EMN3 WiFi Extender

Quick Install Guide - HT-EMN3 - WiFi Extender 5
Step 5: How to Best Place your HT-EMN3
1 MoCA or Ethernet
Place in an area where your existing gateway does not provide
good Wi-Fi coverage.
Must be on the same coax or Ethernet network as the gateway
to work properly.
2 WiFi to WiFi
The HT-EMN3 must be placed where it receives strong Wi-Fi signal
from the gateway. If not, performance will degrade.
Look at the WPS LED indicator to witness wireless signal strength
(see below notes).
Step 6: Confirming WiFi to WiFi Setup
1 HT-EMN3 steady WPS LED confirm WiFi to WiFi is active.
2 The color LED indicates the strength of the wireless signal.
Gateway
HT-EMN3 WiFi Extender
HT-EMN3 WiFi Extender
Green: Strong
Red: Low

Hitron Technologies Americas6
LEDs
WARNING
Risk of electrical shock. Do not expose the device to water or moisture. The device is a high-performance
communications device designed for home and office environments. Do not use the device outdoors.
Keep the device in an environment between 0°C ~ 40°C (32°F ~104°F). To avoid overheating, do NOT
place any object on top of the device. Do not restrict the flow of air around the device. The manufacturer
assumes no liabilities for damage caused by any improper use of the device.
DISCLAIMER
The manufacturer assumes no liabilities with respect to the contents of this document. The manufacturer
also reserves the right to revise this document or update the content thereof without any obligation to
notify any person of such revisions or amendments. Specifications subject to change without notice.
CAUTION
(i) the device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for
harmful interference to co-channel mobile satellite systems; (ii) the maximum antenna gain permitted for
devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits
specified for point-to-point and non-point-to-point operation as appropriate.
RADIATION EXPOSURE STATEMENT
This equipment complies with ISED radiation exposure limits set forth for an uncontrolled environment. This
equipment should be installed and operated with minimum distance 40cm between the radiator & your
body.
FCC INTERFERENCE STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and
(2) this device must accept any interference received, including interference that may cause undesired
operation. This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part15 of the FCC Rules. These limits are designed to provide reasonable protection against
harmful interference in a residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.
Power Green when powered on.
Ethernet . Green for Ethernet connection.
MoCA Blue high-speed mode.
Green low-speed mode.
Off if not connected to
another MoCA device.
Wireless 2.4GHz Green when 2.4GHz WiFi on
5GHz Green when 5GHz WiFi on
WPS Green when WPS on

Quick Install Guide - HT-EMN3 - WiFi Extender 7
FCC CAUTION
Any changes or modifications not expressly approved by the party responsible for compliance could
void the user’s authority to operate this equipment. This device is going to be operated in 5.15~5.25GHz
frequency range, it is restricted in indoor environment only. This device meets all the other requirements
specified in Part 15E, Section 15.407 of the FCC Rules. For product available in the USA/Canada market,
only channel 1~11 can be operated. Selection of other channels is not possible. This device and it’s
antennas(s) must not be co-located or operating in conjunction with any other antenna or transmitter
except in accordance with FCC multi-transmitter product procedures.
© Hitron Technologies Americas. The Hitron name and the Hitron logo are registered trademarks
of Hitron Technologies in the US and other countries. Any non-Hitron trademarks are used for reference
purposes only.

Quick Install Guide - HT-EMN3 - WiFi Extender