HOLMS 246564-005 Guide

Originalspråk: Svenska © HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302. English
Driver instruction
Spare parts list
Box 924 S-591 29 Motala Sweden [phone] ¬[phone]
Artikelnummer: 246542-G / 246548-B
Wireless control

Wireless control
© HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302. 3
Warning labels..............................................................4
Safety ...........................................................................7
Product data.................................................................9
Description .................................................................10
Description transmitter ...............................................11
Description receiver....................................................11
Connection .................................................................12
Connection receiver to transmitter ....................12
Functions for different attachments............................13
Installation, service and maintenance ........................16
Connecting the attachment ...............................16
Connecting to joystick .......................................17
Mounting instruction (transmitter-joystick) ........17
Special function 1 and 2....................................18
Connecting instructiononteringsanvisning (från
sändare till spakknopp (tillbehör)). ....................18
Monteringsanvisning (från sändare till spakknopp
(tillbehör)). Styrning av vikplog..........................19
..........................................................................19
Fault finding................................................................20
Overload protector ............................................20
Spare part List............................................................22
Mottagare / Receiver ..................................................24
Index...........................................................................26
Contents

Wireless control
4© HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302.
Warning labels
There are several specific warning labels on this product; see the descriptions below. Make sure that
you understand the implications of these labels before using the product.
Clean/replace warning labels if they are illegible or are missing. Contact you Holms dealer if you
require new labels.
Risk of crushing - mind your hands and do not come too close to the machine (warning label
1530052)
Do not enter this area whilst the machine is in
operation. Mind your hands and keep them away
from this area whilst the tool is in use.
Keep a safe distance away from the machine
whilst it is in operation. Not following this rule
may lead to serious personal injury or, in a worst
case scenario, death.
Risk of crushing - do not come too close to the machine (warning label 1530053)
Keep a safe distance away from the machine
whilst it is in operation. Not following this rule
may lead to serious personal injury or, in a worst
case scenario, death.

Wireless control
© HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302. 5
Always read instructions and safety regulations before use (warning label 1530054)
Do not use the tool before you have thoroughly
studied all instructions and safety regulations,
and are sure you have understood them. If there
is something you do not understand, contact your
Holms dealer. Misinterpretations may result in
serious personal injury or, in a worst case
scenario, death.
Risk of crushing, beware of flying objects - mind your hands and do not come too close to the
machine (warning label 1530055)
Keep a safe distance from the tool whilst it is
being used and beware of flying objects. Not
following this rule may lead to serious personal
injury or, in a worst case scenario, death.
Use the marked loops when transporting the tool (warning label 1530056)
When transporting the tool, use the marked loops
to secure the tool during transit.

Wireless control
6© HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302.
Attach lifting devices at the marked locations when lifing the tool (warning label 1530057)
This label shows where the lifting devices are to
be attached. Make sure that the lifting devices are
attached so that the tool is lifted horizontally (in
horizontal position, no inclination). Use
approved lifting devices only.
Risk of crushing - mind your hands (warning label 1530060)
Mind your hands and keep them away from this
area whilst the tool is in use.

Wireless control
© HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302. 7
NB
READ THIS DOCUMENT CAREFULLY BEFORE USING THE EQUIPMENT.
Important safety aspects to take into consideration
• Make sure that the tractor/loader can carry the equivalent tool type and weight.
• Make sure that for this sweeper the carrier has a suitable hydraulic oil flow.
• Make sure that no unauthorised persons are loitering in the machine’s working area when working
with the machine or carrying out servicing.
• Always use the dust covers for the quick-couplings when the machine is disconnected, to prevent
dirt getting into the hydraulic system.
Safety
This instruction manual is intended to be used as a guide for the correct use and maintenance of the
machine. Study the manual carefully before starting and operating the machine and before any
preventive maintenance is carried out. A lot of time has been spent on designing and manufacturing
the machine so that it will be as efficient and safe as possible, all of which will be of little use if you
do not read, understand and follow the instructions. Familiarise yourself with the product and all the
instructions, and keep the instruction manual safe so that it is always readily at hand when using the
machine.
NB
THIS MANUAL HAS BEEN PREPARED FOR ALL OUR MARKETS AND MAY THEREFORE INCLUDE DIFFERENT
EQUIPMENT FOR SPECIFIC MARKETS. PLEASE IGNORE THE SECTIONS THAT DO NOT APPLY TO YOUR
MACHINE.
We continuously strive to improve our products and therefore reserve the right to change design
specifications and implement improvements whenever we consider this necessary; however, such
improvements will not be made to products that have already been delivered or put to work. We also
reserve the right to change data and equipment without prior notice, as well as instructions for
maintenance and other service procedures.
The operator is responsible for ensuring that:
Please pay special attention to the warning symbols.
Make sure you tighten the screw joint reinforcement.
The machine is not used or handled incorrectly.
That any warning labels on the machine are legible.
Unauthorised persons do not use the machine or remain within the machine’s
working area during its operation or maintenance.

Wireless control
8© HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302.
NB
WESTRONGLY ADVISE AGAINST ANY MODIFICATIONS, CHANGES OR CONVERSIONS THAT HAVE NOT BEEN
APPROVED BY HOLMS. WEALSO WARN AGAINST USING SPARE PARTS THAT HAVE NOT BEEN APPROVED
BY HOLMS. DAMAGE OR FAULTS THAT COULD HAVE BEEN CAUSED BY NON-APPROVED SPARE PARTS OR
NON-APPROVED MODIFICATIONS ARE NOT COVERED BY HOLMS’ LIMITED WARRANTY – SEE APPLICABLE
WARRANTY CONDITIONS. HOLMS WILL NOT PROVIDE COMPENSATION FOR ANY PERSONAL INJURY OR
MATERIAL DAMAGE RESULTING FROM THE USE OF NON-APPROVED SPARE PARTS OR MODIFICATIONS.
When ordering spare parts, or otherwise contacting Holms or your local dealer, always specify the
machine type and its serial number. (Specified on the product’s machine plate.)
The carrier is suitable for use with the machine (hydraulic oil flow, stability,
etc.).

Wireless control
© HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302. 9
Product data
Transmitter
Measurement l/w/h 147/88/25 mm
Cable length 2000mm
Voltage 10-28 VDC
Frequency 2,4 GHz
Receiver
Measurement l/w/h 130/80/60 mm
Cable length 3000mm
Voltage 10-28 V
Frequency 2,4 GHz

Wireless control
10 © HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302.
Description
The wireless control to run Holms attachments is divided
in 2 units. Transmitter and receiver. The transmitter is
mounted inside the drivers cabin close to the person
running the machine, it controlls the attachment thats
being used. The receiver is mounted on to the attachment.
The system is communicating wireless by radio, 2.4GHz.
The receiver scans all chanels and chooses the one with
less interuptions and directs the transmitter to it.
The receiver will save the latest transmitter that was
connected and will at start up try to connect to that one. If
that transmitter doesn’t respond the receiver will search
for another avalible transmitter. I new transmitter may be
installed during a certain amount of time (20 sec). The
communication is controlled so that correct messages is
received with certain time interval. In case of
communication problems the transmitter is automaticly
set to go into safe mode.
1.Transmitter

Wireless control
© HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302. 11
Description transmitter
The transmitter is basically a box with electronic’s. You
manouvre it with the buttons on the display. There are
eight buttons on the display with ten associated LEDs,
see figure 2. The buttons have different functions
depending on which attachment is connected.
The transmitter is equipped with automatic adjustment of
the brigtness in the diode lamps. The adjustment is done
when you start the system, it is also possible to manually
adjust by pushing button number 4 while running the
system (all the diode lamps will then be turned off during
the time when it’s meassured).
The transmitter is connected with the cable to the electric
outlet, 12V or 24V inside the cabin.
The transmitter is equipped with a overflow guard, see
“Fault finding” page 20.
Description receiver
The receiver is a box with electronics and cabling. The
cabels may be connected to electric outlet 12V or 24V,
electric valve on hydraulic block or on the electric water
pump and to the lights. This all depends on what type of
attachment you are about to use and how it is equipped.
To reduce risk of injury, always make sure to have
the wireless control mounted inside the drivers
cabin.
2.Transmitter

Wireless control
12 © HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302.
Connection
The transmitter will connect to the latest used receiver/
attachment.When a new receiver/attachment is used
make sure the latest receiver/attachment is shut down.
Connection receiver to transmitter
1. Connect the attachment to the carrier.
2. Connect the receiver to the carrier’s electric outlet,
12V or 24V.
3. Connect the transmitter to the electric outlet inside the
cabin, 12V or 24V.
4. When the transmitter is ready for signal from the
receiver the diode lamp in button number 4 will blink
slowly.
5. When the transmitter is reciving the signal from the
receiver the diode lamp in button number 4 will blink
fast again. Confirm the connection within 20 seconds
by pushing button number 4.
6. If the connection is succesfull the diode lamp in
button number 4 will be on constantly and the the
attachment is now ready to be operated by the
transmitter.
Make sure the attachment is connected properly
and all the functions work according to the
manual/instruction before use.
3.Transmitter

Wireless control
© HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302. 13
Functions for different attachments
See the transmitters display.
Sandspreading bucket
Button 1
Decrease the material spread, the diode lamp will
light up at adjustment (will darken at min/max). Set
rotation speed will be saved until next time of use.
Button 2
Increase the material spread, the diode lamp will
light up at adjustment. Set rotation speed will be
saved until next time of use.
Button 3
Button 4
Button 5
Button 6
Button 7
Button 8
Function 9
If the units have a connection and this is broken, the
LED warning light starts flashing red. See more
under troubleshooting
Function
10
Constant light indicates that the machine component
voltage is too low.
A blinking LED indicates low voltage on the handset.
The LED flashes at a voltage below 10.2 volts. See
more under troubleshooting
Pick-up Sweeper
Button 1
Side brush left (only 300 and Dustbuster). Quick
push for on/off. The diode lamp will light up when the
brush is rotating. Hold the button for increase/
decrease the rotation of the brush. When increasing
the speed the diode lamp will blink fast. Decreasing,
the diode lamp will blink slowly. Latest set will be
saved until next time of use. This is set between 22–
85 rpm
Button 2
Side brush right (only 300 and Dustbuster). Quick
push for on/off. Other functions please see
above.This is set between 22–85 rpm
Button 3
Water spray system on/off. The diode lamp will light
up when the water is on/spraying. Holding the button
will adjust how much water is sprayed, 1/2 the time,
2/3 of the time or constant. There are three different
settings. Change by holding the button and then let
it go. Latest setting will be saved until next time of
use.
Button 4
Button 5

Wireless control
14 © HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302.
Button 6
Button 7
Button 8
Function 9
If the units have a connection and this is broken, the
LED warning light starts flashing red. See more
under troubleshooting
Function
10
Constant light indicates that the machine component
voltage is too low.
A blinking LED indicates low voltage on the handset.
The LED flashes at a voltage below 10.2 volts. See
more under troubleshooting
Sweeper roller
Button 1 Angling left. The diode lamp will light up at
adjustment.
Button 2 Angling right. The diode lamp will light up at
adjustment..
Button 3
Water spray system on/off. The diode lamp will light
up when the water is on. Holding the button will
adjust how much water is sprayed, 1/2 the time, 2/3
of the time or constant. There are three different
settings. Change by holding the button and then let
it go. Latest setting will be saved until next time of
use.
Button 4
Button 5
Button 6
Button 7
Button 8
Function 9
If the units have a connection and this is broken, the
LED warning light starts flashing red. See more
under troubleshooting
Function
10
Constant light indicates that the machine component
voltage is too low.
A blinking LED indicates low voltage on the handset.
The LED flashes at a voltage below 10.2 volts. See
more under troubleshooting
Pick-up Sweeper

Wireless control
© HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302. 15
V-plow
Button 1
Button 2
Button 3
Button 4
Button 5
Button 6
Selection of plow function/control of plow half. The
LED is lit for activated functions. The latest settings
will be saved for the next use. Controls the left plow
half.
Button 7 As button 6, but controls the diagonal function (both
blade halves are controlled).
Button 8 As button 6, but controls the right plow half
Function 9
If the units have a connection and this is broken, the
LED warning light starts flashing red. See more
under troubleshooting
Function
10
Constant light indicates that the machine
component voltage is too low.
A blinking LED indicates low voltage on the handset.
The LED flashes at a voltage below 10.2 volts. See
more under troubleshooting

Wireless control
16 © HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302.
Installation, service and maintenance
Connecting the attachment
Connect the electric wire to on the attachment to a trailer
plug on the carrier. Minus to 3/31 and
plus to 5/58R and 7/58L.
The receiver have 3 circuit breaks, 9 contacts (4 outlets,
2 inputs and 3 spare contacts) 1 jumper position (J11)
with 3 spots and 11 diod lamps. The transmitter may be
configured to control different attachment.
To set the transmitter for different attachments, use the
jumper position J11, see figure 1.
No jumper mounted (000) Sandspreading bucket
1 jumper in position3 (001) Pick-up sweeper
1 jumper in position2 (010) Sweeper roller
2 jumper in position3 and 2 (011) V-plow
4.Jumper position(receiver circuit card)
1’2.3
J11

Wireless control
© HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302. 17
Connecting to joystick
The functions on the transmitter may be connected to the
carriers manouvre unit for example the Joystick. This
requires a separate “connection pack” including contact
block and cabling (the connection pack has to be orderd
separate). A spring-back pressure switch is also needed
for each function.
To run the most frequent functions thru the Joystick use
the circuit diagrams special functions, see “Special
function 1 and 2” page 18.
Mounting instruction (transmitter-joystick)
1. Remove the inlet plugg from the transmitter.
2. Open the transmitter (4 screws on the rear).
3. Put the cable (from the connection pack) with the 4
conductors through the hole and mount the inlet.
4. Connect the power (any conductor) to the contact
block (see figure 5) connection number 9.
5. Choose functions according to diagram 7 and 8 (the
functions on the buttons are sorted by attachment).
6. Connect the other 3 conductors to the contact block,
use connection 1-8, see “Connecting
instructiononteringsanvisning (från sändare till
spakknopp (tillbehör)).” page 18).
7. Mount the contact block on the circuit card in position
J1 (figure 6).
8. Mount the rear plate on the transmitter.
9. Make sure to tighten where the cable runs into the
transmitter.
10. Connect the conductors to the carriers Joystick
according to the diagram in figure 7 on page 18.
Check with the manufacturer of the carrier how the
connection to the joystick is done.
5.Contact block with connection
(included in the connection pack)
6.Connection example with folding plough

Wireless control
© HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302. 18
Special function 1 and 2
Connecting instructiononteringsanvisning (från sändare till spakknopp (tillbehör)).
Attachment type Function 1 Function 2 Note
V-plow PV left side diagonal
will return to right
when button is
released
Sandspreading bucket SB decrease material
spread
increase material
spread
Sweeper roller SL / SH angling left angling right
Pick-up sweeper 300 / SU water spray system
o/off/amount
right gutterbrush
on/off/speed
Connection Button Special
function Note
J 1:1 6
J 1:2 3
J 1:3 4
J 1:4 1
J 1:5 5
J 1:6 2
J 1:7 1
J 1:8 2
J 1:9 joint flow
J 1:10
J1:9
Needed function
ex J1:7
Needed function
ex J1:8
7.Scheme connection to joystick

Wireless control
© HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302. 19
Monteringsanvisning (från sändare till
spakknopp (tillbehör)). Styrning av vikplog
1. Ta bort genomföringspluggen på sändaren.
2. Öppna sändarlådan (4 skruvar på undersidan).
3. För in inkopplingssatsens kabel med de 5 ledarna
genom lådans hål och montera genomföringen.
4. Connect the cables into the two connectors supplied,
according to figure 9. Leave position 1 open
according to figure 9 and then in the colour order
according to figure 8. Remember that the lugs should
be upward on both the connections according to
figure 9.
5. Cable A, green.
6. Cable B, yellow.
7. Cable C, grey.
8. Cable D, white.
9. Cable E, brown.
10. Skruva fast sändarens bottenplatta.
11. Dra åt/ täta kabelgenomföringen.
12. Montera spakknoppen på bärarens spak för 3:e funk-
tion.
8.Handset with lever knob
9. Connections to the lever knob
10.Lever knob with three buttons.

Wireless control
20 © HOLMS INDUSTRI AB, ALL RIGHTS RESERVED 170302.
Fault finding
Overload protector
The circuit card have a overload protector connected to
all outlets. At power more than 20A button number 3 and
5 will start to blink. The over load protector is reset by
button number 4, if the overload continues the buttons
will still be blinking, otherwise everything will go back
to normal.
Function 9 and 10 on the front
Constant light on function 9 (flash)
Radio contact broken between the machine unit and receiver.
Machine unit has been switched off?
Could be a loose connection.
Constant light function 10 (battery)
Low voltage on the machine unit.
The reason is probably a voltage drop
Check the wiring and connectors
Blinking light function 10 (battery)
Low voltage on the handset.
Check system voltage. Should be over 12v.
Check the vehicle’s alternator.
Constant light function 9 (flash) + constant
light function 10 (battery).
Low voltage on the machine unit, which has switched off the machine
unit.
Check the wiring
There may be poor connection and voltage drop.
Check system voltage. At least 12v.
Flashing function 9 (flash) constant light
function 10 (battery) and flashing buttons 1–
8 except 4.
The system has lost radio contact. If the button that was pressed flashes
in the eight, this shows current consumption is too high.
There could be a short circuit in the function.
The connection is broken immediately after
the units have connected.
When ploughing, buttons 6, 7 or 8 can be activated. When button 6 or 7
is activated, the magnetic coils are powered as soon as the units are
connected. If there is poor connection, this is broken and all lights on the
panel are lit for a short time. - Reason: Poor contact.
11.Front with numbers