Klipsch WA-2 User manual

Klipsch·
GROUP
Klipsch·
~amo·
cl'c~c::>•
c
MIRAGE·:>
(Works
Only
with
Subwoofers
with
a
WA
Port)
WA-2
Wireless
Subwoofer
Kit
Owner's
Manual

IMPORTANT SAFETY INSTRUCTIONS!
1. READ these instructions.
2. KEEP these instructions.
3. HEED all warnings.
4. FOLLOW all instructions.
5. DO NOT use this apparatus near water.
6. CLEAN ONLY with dry cloth.
7. DO NOT block any ventilation openings. Install in accordance with the manufacturer's
instructions.
8. DO NOT install near any heat sources such as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that produce heat.
9. DO NOT defeat the safety purpose of the polarized or grounding type plug. A polarized plug
has two blades with one wider than the other. A grounding type plug has two blades and
a third grounding prong. The wider blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult an electrician for replacement of the
obsolete outlet.
1 0. PROTECT the power cord from being walked on or pinched, particularly at plugs, conve-
nience receptacles, and the point where they exit from the apparatus.
11. ONLY USE attachments/accessories specified by the manufacturer.
12. USE only with a cart, stand, tripod, bracket, or table specified by the manufac- ~
turer, or sold with the apparatus. When a cart is used, use caution when moving g
the cart/apparatus combination to avoid injury from tip-over.
13. UNPLUG this apparatus during lightning storms or when unused for long periods of time.
14. REFER all servicing to qualified service personnel. Servicing is required when the ap-
paratus has been damaged in any way, such as power-supply cord or plug is damaged,
liquid has been spilled or objects have fallen into the apparatus, the apparatus has been
exposed to rain or moisture, does not operate normally, or has been dropped.
15. DO NOT expose this apparatus to dripping or splashing and ensure that no objects filled
with liquids, such as vases, are placed on the apparatus.
16. To completely disconnect this apparatus from the AC Mains, disconnect the power supply
cord plug from the AC receptacle.
17. The mains plug of the power supply cord shall remain readily operable.

The
exclamation
point,
within
an
equilateral
triangle,
is
intended
to
alert
the
user
to
the
presence
of
important
operating
and
maintenance
(servicing)
instructions
in
the
literature
accompanying
the
product.
The
lightning
flash
with
arrowhead
symbol
within
an
equilateral
triangle,
is
intended
to
alert
the
user
to
the
presence
of
uninsulated
"dangerous
voltage"
within
the
product's
enclosure
that
may
be
of
sufficient
magnitude
to
constitute
a
risk
of
electrical
shock
to
persons.
WARNING:
To
reduce
the
risk
of
fire
or
electrical
shock,
do
not
expose
this
apparatus
to
rain
or
moisture.
WARNING:
No
naked
flame
sources-
such
as
candles-
should
be
placed
on
the
product.
CAUTION
RISK
OF
ELECTRIC
SHOCK.
DO
NOT
OPEN.
WARNING:
Do
Not
Open!
Risk
of
Electrical
Shock.
Voltages
in
this
equipment
are
hazardous
to
life.
No
user
-
serviceable
parts
inside.
Refer
all
servicing
to
qualified
service
personnel.
WARNING:
This
product
is
intended
to
be
operated
ONLY
from
the
AC
Voltages
listed
on
the
back
panel
or
included
power
supply
of
the
product.
Operation
from
other
voltages
other
than
those
indicated
may
cause
irreversible
damage
to
the
product
and
void
the
products
warranty.
The
use
of
AC
Plug
Adapters
is
cautioned
because
it
can
allow
the
product
to
be
plugged
into
voltages
in
which
the
product
was
not
designed
to
operate.
If
the
product
is
equipped
with
a
detachable
power
cord
,
use
only
the
type
provided
with
your
product
or
by
your
local
distributor
and/or
retailer.
If
you
are
unsure
of
the
correct
operational
voltage,
please
contact
your
local
distributor
and/or
retailer.
CAUTION:
Place
the
equipment
near
a
main
power
supply
outlet
and
make
sure
that
you
can
easily
access
the
power
breaker
switch.

THANK
YOU
Thank
you
for
your
purchase
of
the
KLIPSCH
®
Group
WA-2
Wireless
Subwoofer
Kit.
The
WA-2
will
only
operate
with
select
KLIPSCH
®,
ENERGY
®,
MIRAGE
®
and
JAMQ
®
brand
subwoofers
that
have
a
"
WA
Port"
input
on
the
back
of
the
amplifier
panel
(refer
to
your
subwoofer
owner's
manual).
The
WA-2
is
a2.4
GHz
product
designed
to
wirelessly
transmit
a
signal
up
to
a
50
foot
(15m)
radius.*
PACKING
LIST
1.
Transmitter
2.
Receiver
3.
Power
supply
4.
Audio
cable
5.
Hook
and
loop
strips
6.
This
Owner's
Manual
PRODUCT
REGISTRATION
Register
your
product
online
at
www.klipsch.com/register
•
KLIPSCH
will
keep
you
up-to-date
on
new
products
and
promotions
.
•
Your
personal
information
will
never
be
resold.
•
This
registration
information
is
not
used
for
warranty
purposes.
Please
retain
your
receipt
for
warranty
claims.
*
subject
to
RF
interference
(see
"Troubleshooting
")

SETUP
1.
Decide
where
the
subwoofer
will
go
(refer
to
your
subwoofer
owner's
manual).
2.
Most
receivers
(and
pre-amps)
have
a
line
level
subwoofer
output
labeled
Subwoofer
Pre
Out,
Sub
Out,
SW
Out,
etc.
If
you
have
this
connection,
use
one
of
the
two
male
jacks
on
one
end
of
the
supplied
audio
cable
to
plug
into
that
output,
then
use
the
corresponding
(same
color)
jack
on
the
oppo-
site
end
of
the
cable
and
plug
into
the
WA-2
transmitter
input
"8"
(labeled
"Left/LFE").
In
absence
of
a
subwoofer
output
use
both
male
jacks
on
one
end
of
the
cable
and
connect
the
left
and
right
channel
pre-amp
outputs
from
your
receiver
(if
provided)
(not
tape
outs)
to
"8"
(labeled
"Left/LFE")
and
"D"
(labeled
"Right")
inputs
on
the
WA-2
transmitter.
3.
Connect
the
cable
from
the
WA-2
receiver
to
the
"WA
Port"
on
the
back
of
the
subwoofer.
I
•
~~--~~~~~~~~~----~~~~~MM
TRANSMilTER
REAR
TRANSMilTER
FRONT
RECEIVER
FRONT
~
1
(
a~
-- - ---
-,
~~
/
,'~
~
,
\J
I:
,
~
~
' I . .
·-
·
~·
~-
--
-
-
~_U
~~
)

4.
Plug
supplied
power
supply
cable
into
"E"
on
the
WA-2
transmitter
and
plug
other
end
into
an
AC
wall
outlet.
5.
Check
to
make
sure
Gain
Switch
"A"
is
in
middle
position
(OdB).
This
po-
sition
best
matches
the
output
voltage
of
most
receivers
and
processors.
6.
Turn
receiver/pre-amplifier
on.
7.
Turn
subwoofer
to
"On"
or
"Auto
On"
position.
8.
The
WA-2
transmitter
and
receiver
should
be
automatically
"paired
"
with
their
red
LED's
("C")
on
solid,
and
the
subwoofer
should
now
be
operational.
9.
Some
subwoofers
have
two
screws
on
back
that
will
attach
to
keyholes
("H")
on
the
back
of
the
receiver
box.
For
subwoofers
that
do
not
(JAMO
SUB
800,
ENERGY
ESW-M6
&
ESW-M8,
MIRAGE
MM-6
&
MM-8),
you
can
use
the
supplied
hook
and
loop
strips
to
attach
the
WA-2
receiver
to
the
back
of
subwoofer.
Attach
the
receiver
to
these
subwoofers
on
the
back
at
the
top
left
-hand
corner
of
the
subwoofer
("I").
It
is
recommended
that
you
clean
the
area
on
the
subwoofer
and
transmitter
with
rubbing
alcohol
before
attaching
the
strips.
®
CD
co
)>
(")
="
0
"""
::a
1"1"1
(")
1"1"1
-
<
m
::a
- - - - - - - -------
(
I
~
0
.
.
I
o•
I
0
(j
•
mo
.
.
I
I
0
I
~T
-
-
~
·.
/
I
\
\
\ \
I
'-._'·
.
WA
Port
ljj'
'T
"\
}
I
.
'
14.(
~
))
-..
()
I
\ •
.
_.,~
co
~
~
0
=
><
t--:
I
~~
l
0 "
---
-
--
-
- - - - - - -
"-="
BACK
OF
SUBWOOFER

TRANSMITTER CONNECTIONS
--
\
~
~@~
~~[9]
j
\_
I I \
- -- l l \
I I
I ( ) I \
I \ \
Sub Pre Out ® HDMIOut \ \
+€)
In In \\ Pre Out1 Amp In
Video €)(§)(§)
®®
L '®:®
I
0 €)(§)(§) L -®
~®
R
®®
@)
®®®
R
TV DVD
Front Right F
TV DVD CBUSAT
A/V RECEIVER
STEREO RECEIVER
TROUBLESHOOTING
• If the subwoofer does not operate and the red LED's ("C") are flashing
on the WA-2 transmitter and receiver, a simple "pairing" is needed.
Push and hold in button "F" on the transmitter while pushing and hold-
ing button "G" on the receiver and keep pushed until both LED's stop
flashing and glow solid (approximately five seconds).
• Since the WA-2 is a wireless device, it may encounter RF interference
from other wireless devices in the same area. If there is difficulty "pair-
ing" the transmitter and receiver, or their signal connection fades, you
may need to move them closer together and/or farther away from other

wireless products. If other wireless devices in the area have a manual
channel selection option, you can also select a different channel for
their operation to help eliminate interference with the WA-2.
• If you do not get a signal, or get a low level audio signal from the
subwoofer, make sure the subwoofer out level control on your surround
receiver is set correctly (usually at the halfway point sometimes labeled
"OdB"). If your subwoofer out level on your surround receiver is correct,
and you have adjusted the subwoofer volume level and the signal is
still too low, move the gain control "A" to the right (+ 12dB) to increase
the signal to the subwoofer. If the signal is too high, move the gain
control to the left ( -12dB) to reduce signal strength.
WARRANTY - U.S. AND CANADA
KLIPSCH warrants to the original retail purchaser that this product is to
be free from defective materials and workmanship for a period of two (2)
years from the date of purchase, if it is properly used and maintained. If this
product proves defective in either material or workmanship, KLIPSCH, at its
option, will (a) repair the product, or (b) replace the product, at no charge
for parts or labor. If the product model is no longer available and cannot be
repaired effectively or replaced with an identical model, KLIPSCH at its sole
option may replace the unit with a current model of equal or greater value.
In some cases, modification to the mounting surface may be required where
a new model is substituted. KLIPSCH assumes no responsibility or liability
for such modification. To obtain a repair or replacement under the terms of
this warranty, please return to dealer first, if possible, and they will direct
you accordingly for repairs or replacement. You will be required to submit a
copy of the original receipt.

Limitations:
•
This
limited
warranty
does
not
cover
failure
of
the
product
resulting
from
improper
installation,
misuse,
abuse,
accident,
neglect,
mishan-
dling,
or
wear
from
ordinary
use
or
environmental
deterioration.
•
This
limited
warranty
does
not
cover
cosmetic
damage,
including
paint
damage,
or
consequential
damage
to
other
components
or
premises
which
may
result
for
any
reason
from
the
failure
of
the
product.
•
This
limited
warranty
is
null
and
void
for
products
not
used
in
ac-
cordance
with
KLIPSCH's
instructions.
•
This
limited
warranty
is
null
and
void
for
products
with
altered
or
missing
serial
numbers
and
for
products
not
purchased
from
an
authorized
dealer.
•
This
limited
warranty
terminates
if
you
sell
or
otherwise
transfer
this
product
to
another
party.
THIS
WARRANTY
GIVES
YOU
SPECIFIC
LEGAL
RIGHTS,
AND
YOU
MAY
ALSO
HAVE
OTHER
RIGHTS
WHICH
VARY
FROM
STATE
TO
STATE,
JURISDICTION
TO
JURISDICTION
OR
COUNTRY
TO
COUNTRY.
KLIPSCH'S
RESPONSIBILITY
FOR
MALFUNCTIONS
AND
DEFECTS
IN
HARDWARE
IS
LIMITED
TO
REPLACEMENT
OR
REPAIR
AS
SET
FORTH
IN
THIS
WARRANTY
STATEMENT.
FOR
CANADIAN
CUSTOMERS,
KLIPSCH
DISCLAIMS
ALL
OTHER
WARRANTIES
AND
CONDITIONS,
EXPRESS
OR
IMPLIED,
STATU-
TORY
OR
OTHERWISE,
FOR
THE
PRODUCT.
FOR
U.S.
CUSTOMERS,
ALL
EXPRESS
AND
IMPLIED
WARRANTIES
FOR
THE
PRODUCT,
INCLUDING
BUT
NOT
LIMITED
TO
ANY
IMPLIED
WARRANTIES
OF
MERCHANTABILITY
AND
FITNESS
FOR
A
PARTICULAR
PURPOSE
ARE
LIMITED
IN
TIME
TO
THE
TERM
OF
THIS
WARRANTY.
SOME
STATES,
JURISDICTIONS
OR
COUNTRIES
DO
NOT
ALLOW
THE
EXCLUSION
OF
CERTAIN
IMPLIED
WAR-
RANTIES
OR
CONDITIONS,
OR
LIMITATIONS
ON
HOW
LONG
AN
IMPLIED
WARRANTY
OR
CONDITIONS
LASTS,
SO
THIS
LIMITATION
MAY
NOT
APPLY

TO
YOU.
KLIPSCH
DOES
NOT
ACCEPT
LIABILITY
FOR
SPECIAL,
INDIRECT,
CONSEQUENTIAL
OR
INCIDENTAL
DAMAGES,
INCLUDING
WITHOUT
LIMITATION,
ANY
LIABILITY
FOR
THIRD
PARTY
CLAIMS
AGAINST
YOU
FOR
DAMAGES
OR
FOR
PRODUCTS
NOT
BEING
AVAILABLE
FOR
USE.
THE
MAXIMUM
LIABILITY
FOR
WHICH
KLIPSCH
MAY
BE
RESPONSIBLE
WILL
BE
NO
MORE
THAN
THE
AMOUNT
YOU
PAID
FOR
THE
PRODUCT
THAT
IS
THE
SUBJECT
OF
THE
CLAIM.
SOME
STATES,
JURISDICTIONS
OR
COUNTRIES
DO
NOT
ALLOW
THE
EXCLUSION
OR
LIMITATION
OF
SPECIAL,
INDIRECT,
INCIDENTAL
OR
CONSEQUENTIAL
DAMAGES,
SO
THE
ABOVE
LIMITATION
OR
EXCLUSION
MAY
NOT
APPLY
TO
YOU.
WARRANTY
OUTSIDE
THE
U.S.
AND
CANADA
The
Warranty
on
this
product
if
it
is
sold
to
a
consumer
outside
of
the
United
States
and
Canada
shall
comply
with
applicable
law.
To
obtain
any
applicable
warranty
service,
please
contact
the
dealer
from
which
you
purchased
this
product
,
or
the
distributor
that
supplied
this
product.
FCC
AND
CANADA
EMC
COMPLIANCE
INFORMATION
NOTE:
This
equipment
has
been
tested
and
found
to
comply
with
the
limits
for
a
Class
B
digital
device,
pursuant
to
part
15
of
the
FCC
Rules.
These
limits
are
designed
to
provide
reasonable
protection
against
harmful
interference
in
a
residential
installation.
This
equipment
generates,
uses
and
can
radiate
radio
fre-
quency
energy
and,
if
not
in-stalled
and
used
in
accordance
with
the
instructions,
may
cause
harmful
interference
to
radio
communications.
However,
there
is
no
guarantee
that
interference
will
not
occur
in
a
particular
installation.
If
this
equip-
ment
does
cause
harmful
interference
to
radio
or
television
reception,
which
can
be
determined
by
turning
the
equipment
off
and
on,
the
user
is
encouraged
to
try
to
correct
the
interference
by
one
or
more
of
the
following
measures:

•
Reorient
or
relocate
the
receiving
antenna.
•
Increase
the
separation
between
the
equipment
and
receiver.
•
Connect
the
equipment
into
an
outlet
on
a
circuit
different
from
that
to
which
the
receiver
is
connected.
•
Consult
the
dealer
or
an
experienced
radio!TV
technician
for
help.
Approved
under
the
verification
provision
of
FCC
Part
15
as
a
Class
B
Digital
Device.
Caution:
Changes
or
modifications
not
expressly
approved
by
the
manufacturer
could
void
the
use(s
authority
to
operate
this
device.
This
Class
B
digital
apparatus
complies
with
Canadian
ICES-003.
Cet
appareil
numerique
de
Ia
classe
B
est
conforme
a
Ia
norme
NMB-003
du
Canada.
WIRELESS
TRANSMITTER
COMPLIANCE
INFORMATION
The
term
"IC:"
before
the
radio
certification
number
only
signifies
that
Industry
Canada
technical
specifications
were
met.
This
equipment
complies
with
FCC
and
IC
radiation
exposure
limits
set
forth
for
an
uncontrolled
environment.
This
equipment
should
be
installed
and
operated
with
minimum
distance
20cm
between
the
radiator
and
your
body.
This
transmit-
ter
must
not
be
co-located
or
operating
in
conjunction
with
any
other
antenna
or
transmitter.
Le
terme
«IC:»
avant
le
numero
de
certification
radio
signifie
seulement
que
les
specifications
techniques
d'lndustrie
Canada
ant
ete
respectees.

Cet
appareil
est
conforme
a
FCC
et
IC
!'exposition
aux
rayonnements
limites
fixees
pour
un
environnement
non
controle.
Get
appareil
doit
etre
installe
et
utilise
avec
une
distance
mini
male
de
20
em
entre
le
radiateur
et
votre
corps.
Cet
trans-
metteur
ne
doit
pas
etre
co-situe
ou
operant
en
liaison
avec
toute
autre
antenne
ou
transmetteur.
This
device
has
been
designed
to
operate
with
the
antennas
listed
below,
and
having
a
maximum
gain
of
[x]
dB.
Antennas
not
included
in
this
list
or
having
a
gain
greater
than
[x]
dB
are
strictly
prohibited
for
use
with
this
device.
The
required
antenna
impedance
is
50
ohms.
Operation
is
subject
to
the
following
two
conditions:
(1)
this
device
may
not
cause
interference,
and
(2)
this
device
must
accept
any
interference,
including
interfer-
ence
that
may
cause
undesired
operation
of
the
device.
To
reduce
potential
radio
interference
to
other
users,
the
antenna
type
and
its
gain
should
be
so
chosen
that
the
equivalent
isotropically
radiated
power
(e.i.r.p.)
is
not
more
than
that
permitted
for
successful
communication
..
EU
COMPLIANCE
INFORMATION:
Eligible
to
bear
the
CE
mark,
Conforms
to
European
Union
Low
Voltage
Direc-
tive
2006/95/EC;
Conforms
to
European
Union
EMC
Directive
2004/1
08/EC.

WEEE
NOTICE
Note:
This
mark
applies
only
to
countries
within
the
European
Union
(EU)
and
Norway.
This
appliance
is
labeled
in
accordance
with
European
Directive
2002/96/EC
concerning
waste
electrical
and
electronic
equip-
ment
(WEEE).
This
label
indicates
that
this
product
should
not
be
disposed
of
with
household
waste
.
It
should
be
deposited
at
an
appropriate
facility
to
enable
recovery
and
recycling.
Klipsch,
Jamo,
Energy
and
Mirage
are
registered
trademarks
of
Klipsch
Group,
Inc.
and
its
subsidiaries.

.
'
~
ipsch·
GROUP
3502
Woodview
Trace
Indianapolis,
IN
46268
1-
800-KLIPSCH
•
klipsch.com
©
2011
Klipsch
Speakers