HOMCOM 312-064 User manual

ASSEMBLY INSTRUCTION
INfca090V01_UK
312-064
IMPORTANT, RETAIN FOR FUTURE REFERENCE: READ CAREFULLY
*The picture is only for reference, goods in kind prevail.

1.Using Instruction
● Lift up: Hold the both sides of the desk or the chair and pull
it up equably to the height you need until you hear the sound
"KA".
● Lower down: Hold the both sides of the desk or the chair
and pull it up equably to the highest point, then lower it down
to the lowest point, when you hear the sound "KA".pull it up
to the height you need.(Note: If you pull it up before it
reaches the lowest point, it will get stuck easily)
● The desk board can be adjusted between 0-45 (up and
down),and tighten it by screwing the two rotation buttons on
the both sides.
2.Maintenance
● Traces left by water-based pens such as pencils, pens, and
water color pens can be wiped with water.
● Traces left by oily pen can be wiped by alcohol and balm.
● The desk board is moisture proof and scratch-resistant,
But please do not use any blade to scratch lt.
3.Notices
● This product is suitable for kids aged from 6 to 12.
● Maximum Weight Capacity of Chair: 100 Kg; Maximum
Weight Capacity of Table: 80 Kg.
● This product can only be assembled by adults.
● Please be extra careful and operate correctly when
adjusting the height and the desk board.

A1.Desk board set*1
A3. Drawer*1
A5.Left Sliding Rail*1
A7. Desk Base*2
A11.Wand Tube*2
A13.Backrest*1
A15.Feet tube*2
A2.Desk leg*1
A6.Right Sliding Rail"1
A10.Chair leg*1
A12.Strengthened Tube*1
A14.Seat pad*1
Please check the below two pictures carefully before
assembling and make sure every components in the pictures
are included in the package.

B2.Dual purpose screw driver
B3.Internal hexagon wrench
B4.Hook*1
B6.M6 screw pad *22 (Pre installed)
B7.Internal hexagon head screw (M5*12)*10(Pre installed)
B8.Internal hexagon head screw (M6*14 )12 (Pre installed)
B10.Cross recessed screw (M5*20 )*4
B12.Cross recessed screw (M4*8 )*4
Desk Assembly:
1.Assemble the two sliding rails (A5&A6) to the desk board
set, and tighten the bolts (B7) and screw pads (B6) with the
internal hexagon wrench (B3).

2.Adjust the drawer with the sliding rail under the
board,(aimingat the installation holes) and tighten up the
bolt (B12) with the internal hexagon wrench.
3.Fix the desk legs (A2) and desk bases (A7) with bolts
(B7+B6)and screw them with the internal hexagon wrench.
Adjust the foot screws so that it can stay on the ground
stably.

4.Put the whole desk board set on the legs. Aiming at the
installation holes, rotate the board, use screws pads (B7)to
fix them, tighten the bolts with the internal hexagon wrench.
5.Assemble the book rack (A4), Hang the hooks to the both
legs. Now you have finished all the assembly of the desk!

Chair Assembly:
1.Fix the chair legs (A10) and the feet tubes (A15) with,
(B8+B6) and screw them with the internal hexagon wrench.
Adjust the foot screws so that it can stay on the ground
stably.
2.Fix the chair bend tubes (A11) and the strengthen tubes
(A12)with bolts (B8) and screw pad (B6).At this step, you
don't need to tighten them up.

3.Put the seat pad on the wand tubes, aiming at the holes,
and fix them with bolts (B10), at this step, you don't need to
tighten them up.
4.Insert the backrest into the wand tubes, aiming at the
holes, and use the locking rotary knob (B5) to tighten.
Adjust all installation holes and then screw all the bolts
with the internal hexagon-wrench.Now you have finished
all the assembly of the chair!

Done