Home Accents Holiday 1004363934 User manual

Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a) READ AND FOLLOW ALL SAFETY
INSTRUCTIONS.
b) This product is for indoor use only. The electrical rating 1.5 A 120 V 60
Hz.
c) Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor applications,
connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If
one is not provided, contact a qualified electrician for proper installation.
d) This seasonal use product is not intended for permanent installation or
use.
e) Do not mount or place near gas or electric heaters, fireplace, candles or
other similar sources of heat.
f) Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
g) Do not let lamps rest on the supply cord or on any wire.
h) Unplug the product when leaving the house, when retiring for the night,
or if left unattended.
i)Thisisanelectricproduct–notatoy! Toavoidriskoffire,burnspersonal
injuryandelectricshockitshouldnot beplayedwithorplacedwheresmall
children can reach it.
j) Do not use this product for other than its intended use.
k) Do not hang ornaments or other objects from cord, wire, or light string.
l) Do not close doors or windows on the product or extension cords as this
may damage the wire insulation.
m)Do not cover theproductwithcloth,paperoranymaterialnotpartof the
product when in use.
n) Read and follow all instructions that are on the product or provided with
the product.
o) SAVE THESE INSTRUCTIONS.
Package Contents
A. Tree top
Qty: 1 B. Tree center Qty: 1 C. Tree bottom Qty: 1
D. Stand with an eye
bolt
Qty: 1
E. Power cord
Qty: 1 F. Remote control Qty: 1
7.5FT 5000L CAVALIER LED MICRO DOT COLOR
CHANGING 8 FUNCTIONONE PLUG
SKU# 1004363934
Assembly
Assembling the tree stand
Step 1. Choose a location near a wall outlet.
Step2. Open the standto a 90 degree angleuntil the hole linesupwith the
hole on the tube.
Step 3. Screw an eye bolt into the hole.
CAUTION! – ALWAYS UNPLUG YOUR TREE
FROM ITS POWER SOURCE BEFORE ASSEMBLING OR
DISASSEMBLING.
Assembling the tree
Pleaseremove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Insert tree bottom (C) into the tree stand and tighten the screw.
(See Fig. 1)
Step 2. Insert middle section (B) into the tree bottom (C). (See Fig. 2)
Step 3. Insert tree top (A) into the middle section (B). (See Fig. 3)
Step 4. Insert the provided power cord into the connector on the tree
bottom (C) in right direction porperly and tightly (always match the
protuberance of the end connector of power cord to the concave
of the connector found on the tree bottom (C) according to the
magnified drawing on fig. 4.).
Step5. Allowbranchestofall into placeorgentlypull branchesup andout.
When adjusting branches be sure that all wires are free of branch
hinges. (See Fig. 5)
Step 6. Shape the branches. Starting with tips closest to the pole, shape
one tip to the right, one to the left and one at the center of themain
stem. Repeat pattern for each branch. (See Fig. 6)
Step 7. Plug the power cord into a proper outlet. This tree comes with a
control box and a remote control for easy illumination and
changing functions. This tree is Color Changing, the 8 lighting
options available are:
1. Steady Warm White
2. Flashing Warm White
3. Fade In and Fade Out Warm White
4. Steady Multicolor
5. Flashing Multicolor
Pre-Assembly

6. Fade In and Fade Out Multicolor
7. Sequential Multicolor & Warm White
8. Color Changing
These functions can be changed by using control box or remote
control.
Please see Instructions of control box and remote control as
below.
Operation
Turning on the tree
Step 1. Connect each tree section well and plug the well-connected power
cord into a wall outlet.
Instruction of control box and remote
control
Instruction of control box
1. Press the ON/OFF button on control box to turn on and off the tree
lights.
2. Press the MODE button on control box to select below functions:
1. Steady Warm White
2. Flashing Warm White
3. Fade In and Fade Out Warm White
4. Steady Multicolor
5. Flashing Multicolor
6. Fade In and Fade Out Multicolor
7. Sequential Multicolor & Warm White
8. Color Changing
3. In the state of function 2, 3, 5, 6, 7 or 8:
presstheSPEED+button,thespeedofthecorrespondingfunctionis
faster.
presstheSPEED- button, the speed of the correspondingfunctionis
slower.
There is memory mode on functions whether the tree is re-started.
It has Output Short-circuit Protection
When the load is short-circuited, the output can be automatically
closed. After eliminating the short circuit and restarting the power on,
it can return to normal.
Instruction of remote control
Please note this tree has a remote control.
Please pull out the insulation tape from the remote control, before starting
to use it.
1. Press Fn button, the function below cycle. Press the number key,
select from the following corresponding lighting functions:
Function 1: Steady Warm White
Function2: Flashing Warm White
Function3: Fade In and Fade Out Warm White
Function 4: Steady Multicolor
Function5: Flashing Multicolor
Function6: Fade In and Fade Out Multicolor
Function7: Sequential Multicolor & Warm White
Function 8: Color Changing
If the remote control does not work, check whether the battery of the
remote control is out of power.
To replace the remote control battery:
1. Replace with a new button cell “CR2025” (3 volt)
into the compartment.
CAUTION: DO NOT DISPOSE OF
BATTERIES IN FIRE. BATTERIES MAY EXPLODE
OR LEAK.
CAUTION: The product consists of non-replaceable LED
lamps. To reduce the risk of fire or electric shock, do not attempt to
replace lamps or modify string.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the power cord from the wall outlet. And remove your
power cord from tree bottom (C) and save them.
Step3. Gentlyliftthe treetopstraightup toremovefromthe center section
and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step5. Carefullyplacealltreesectionsintoashippingboxandtapeitshut.
Step 6. Store your tree in a cool, dry place away from sunlight.
Troubleshooting
Problem
Solution
The tree
does not
light
Ensure that all tree sections are connected into each
other well by pressing each section down and rotating.
Make sure the power cord is well connected to the tree
bottom (C) and thetreeispluggedintothe walloutlet.
Ifyouarestillexperiencingproblemswiththetreeplease
call 1-877-527-0313 for instructions.

Warning: Please note that changes or modifications
not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
● Reorient or relocate the receiving antenna.
● Increase the separation between the equipment and
receiver.
● Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
● Consult the dealer or an experienced radio/TV technician
for help.
Adapter Model No. RHD75W240300