Home Accents Holiday 1005178730 User manual

Safety Information
Pre
- Assembly
6.5 FT FESTIVE PINE WITH 250L LED COLOR
CHANGING 3 FUNCTIONS
SKU#1005178730
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a)
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
b)Donotusethis productoutdoors.This product isforindooruseonly.
The electrical rating 0.8A120 V60 Hz.
c) This seasonal use product is not intended for permanent installation
oruse.
d)Donotmountorplaceneargasorelectricheaters,fireplace,candles
orothersimilar sourcesof heat.
e) Unplug the productwhenleavingthehouse,when retiring for the
night,or if leftunattended.
f)Do not use this product for other than its intended use.
g) Do not hang ornaments or other objects from cord, wire, or light
string.
h) Do not cover the productwithcloth,paperor any materialnot partof
the product when in use.
i)Thisproductis equippedwithpush-intypelamps.Donottwistlamps.
j) Thisproductemploysoverload protection(fuse).Ablownfuse
indicatesanoverloador short-circuitsituation.Ifthe fuseblows,unplug
the product from the outlet.Also unplug any additional strings or
products that maybe attached to the product. Replacethefuseasper
the user servicing instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse blows, a
short-circuit may be present and the product should be discarded.
k) Read and follow all instructions that are on the product or provided
with the product.
l) SAVE THESE INSTRUCTIONS.
Use and Care Instructions
a) Beforeusing orreusing.Inspect productcarefully. Discardany
productsthathavecut,damaged,orfrayedwireinsulationorcords,
cracks in lampholders or enclosures, loose connections, or
exposed copper wire.
b) When storingthe product, carefullyremove the product from
wherever it placed, to avoid any undue strain or stress on the
product conductors, connections,and wires.
c) Whennotinuse,storeneatly inacool,drylocation protectedfrom
sunlight.
CAUTION!– ALWAYS UNPLUG YOUR
TREE FROM ITS POWER SOURCE BEFORE
ASSEMBLING OR DISASSEMBLING.
a)CAUTION–Toreduce theriskofelectricshock,useonly
withthepower-supplycord providedor witha cordsetintendedfor
outdooruse.
b) Donotuse acracked,frayed,ordamagedcord.Inspectthecord
periodically.
c) Donotabusecord–Donotcarryproductbythecord oryankorpullit to
disconnectfrom theoutlet.
d) Disconnecttheproductfromtheoutletwhennotinuse. If
abranchof thetree falls off,reinstallit with a sparerivet.
Package Contents
A.Tree top
Qty: 1
B. Tree center
Qty: 1
C. Tree bottom
with base
Qty: 1
D.Legs of Tree base
Qty: 4
E. Power supply
cord
Qty: 1
F. Replacement
bulb
Qty: 6
G. Fuse
Qty: 2
H. Rivet
Qty: 2
Step 1.Choosealocationnearawalloutlet.
Step2.Insertandslidethelegsupwardintotheslotsofthebaseuntilfirmly
secured.(Note:Thebaseisalreadyonthetree section(C)).
Assembling the tree
Pleaseremoveprotectivecoversfromthebaseofthepoleforeachtree
section before assembling.
Step1. Carefully insert the middle section (B) of the tree into the
bottom section (C). (See Fig. 1)
Step2.Insertthetopsection(A)intothemiddlesection(B). (SeeFig.
2)
Step3. Insert the male connector of the middle section (B) intothe
female connectorof the top section (A) in right direction
properly and button on the connectors, the male connector of
thebottom section(C) intothe female connectorofthemiddle
section (B) in right directionproperly and button on the
connectors, themale connector of the power supply cord into
the female connector of the bottom section (C)in right
direction properly and button onthe connectors according to
the magnified drawing on Fig. 6). (See Fig.3,4,5,6)
Assembly
Assembling the tree stand

Operation
User Servicing Instructions
Step 4. Allow branches to fall into place or gently pull branches up and
out. When adjusting branches be sure that all wires are free of
branchhinges. (See Fig. 7)
Step5. Shape the branches. Starting with tips closest to the pole,
shape one tip tothe right, one to the left and one at the center
ofthemainstem. Repeatpatternforeachbranch. (SeeFig.8)
Step 6. Plug the power cord from the tree section (C) into a proper
outlet. Pleasenote this treecomeswithacontrolbox.Press
the button on the control box toselect from the 4 lighting
functions listed below:
1. Warm white steady on 2. Multicolor steady on
3. Color changing 4.Off
Turning on the tree
Step1. Plug the powercordfromthe tree section(C)intoa proper
outlet.
Replace the fuse.
a) Graspplugandremovefromthereceptacle or otheroutlet device.
Do not unplug by pulling on cord.
b) Open fuse cover. Slide open fuse access cover on top of
attachment plug towards blades.
c) Remove fuse carefully.
d) Riskoffire.Replacefuseonlywith3Amp,
125Voltfuse (providedwithproduct).
e) Close fuse cover. Slide closed the fuse access cover on top of
attachment plug.
f) Risk of fire. Do not replace attachment plug. Contains a safety
device(fuse)that shouldnot beremoved. Discard product if the
attachment plug is damaged.
Replace the lamp.
a) Graspplugandremovefromthereceptacleorotheroutletdevice.Do
notunplug by pulling oncord.
b) Unlocktheburnedout LEDbulbbyliftingthe hook andpull lamp and
plasticbase straight out oflampholder.Donot twistbulbs.
c) Replacelamp with only3.0 Volt, 0.06Watt LEDtype lamp.(provided
withproduct)
d) Lockthe LEDbulb.
Ifthe new lamp base does notfit inlampholder, followthesteps
below
beforestepc.
1. Pullthereflector out.
2. Removethe base ofburnedout lampby straightening lamp
leads
andgently pull lamp out.
3. Thread leads of new lamp through holes in old base with one
lead in each hole(always match the long lead of new lamp to
the hook of lamp base)
4. Afterlamp is fully inserted into base, bend eachlead up, likeother
lampsin the light set so thatthe leads will touchthe contactsinside
thelampholder.
5. Insertthe reflector into thebase.
CAUTION!–ALWAYS UNPLUG YOUR TREE FROM
ITS POWER SOURCE BEFORE ATTEMPTING FUSE AND
B
ULB REPLACEMENT.
Step1. Remove all ornaments and decorations.
Step2. Unplug the cord from the wall outlet and then disconnect each
section of the tree. Remove thepowercords fromthe tree
bottom (C).
Step3. Gently lift the treetop straight up toremove fromthecenter
section and fold all branches towards the pole.
Step4. Repeat this step for the center and bottom tree sections.
Step5. Carefully place all tree sections into a shippingbox and tapeit
shut.
Step6. Storeyour treein acool, dry placeawayfrom sunlight.
Problem Solution
The tree
does not
light
Ensurethatconnectorsof all treesections are
connected into each other well. Make surepower
cord plug is securely inserted into a working
electrical outlet.
Checkforblownfusesatthepowercordplug. Replace
asneededwiththereplacementfusesprovided.
Checkforloose,broken,ormissingbulbsandreplace
asneededwiththereplacementbulbsprovided.
If you are still experiencing problems with the tree
pleasecall1-877-527-0313 for instructions.
Model No. LTW605-C5-1
Care and Cleaning
Troubleshooting