Home Accents Holiday 1005405367 User manual

Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a) READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
b)Thisproductisforindooruseonly.Theelectricalrating0.25A120 V60
Hz.
c) Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor applications,
connect the rpoduct to a Ground Fault Circuit Interrupting (GFCI) outlet. If
one is not provided, contact a qualified electrician for poper installation.
d) This seasonal use product is not intended for permanent installation or
use.
e)Donotmountorplaceneargasorelectricheaters,fireplace,candlesor
other similar sources of heat.
f)Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
g) Do not let lamps rest on the supply cord or on any wire.
h) Unplug the product when leaving the house, or when retiring for the
night, or if left unattended.
i) This is an electric product – not a toy! To avoid risk of fire, burns
personal injury and electric shock it should not be played with or placed
where small children can reach it.
j) Do not use this product for other than its intended use.
k) Do not hang ornaments or other objects from cord, wire, or light string.
l)Do not closedoorsorwindowsonthe productor extensioncordsas this
may damage the wire insulation.
m) Do not cover the product with cloth, paper or any material not part of
the product when in use.
n) Do not move the tree by pulling the tree tips or tree branches.
o)Read and follow all instructions that are on the product or provided with
the product.
p) SAVE THESE INSTRUCTIONS.
Package Contents
A.Tree top
Qty: 1
B. Tree center
Qty: 1
C. Tree bottom
Qty: 1
D.Stand with an eye
bolt
Qty: 1
E. Power cord
Qty: 1
F. Remote control
Qty: 1
G. Latch
Qty: 2
7.5 ft Uptown Noble Fir LED Pre-Lit Tree
SKU# 1005405367
Assembling the tree stand
Step 1. Choose a location near a wall outlet.
Step2.Openthestandtoa90degreeangleuntiltheholelinesupwiththe
hole on the tube.
Step 3. Screw an eye bolt into the hole.
CAUTION! – ALWAYS UNPLUG YOUR
TREE FROM ITS POWER SOURCE
BEFORE ASSEMBLING OR
DISASSEMBLING.
Assembling the tree
Please remove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Carefully insert bottom section (C) of tree into tree base and
tighten the screw. (See Fig. 1)
Step 2. Insert the middle section (B) of the tree into the bottom section
(C). (See Fig. 2)
Step 3.Insertthetopsection(A)intothemiddlesection(B). (See Fig.3)
Step 4.Connect theendconnectorofpowercordwithfootpedalswitch(E)
with the connector found on the bottom section (C) in correct
direction(alwaysmatch the protuberanceon the end connectorof
power cord to the concave on the connector found on the bottom
section (C) according to the magnified drawing. (See Fig. 4)
Step 5. Allowbranchestofallintoplaceorgentlypullbranchesupandout.
When adjusting branches be sure that all wires are free of branch
hinges. (See Fig. 5)
Step 6. Shape the branches. Starting with tips closest to the pole, shape
onetiptotheright,one totheleftandoneatthecenterofthemain
stem. Repeat pattern for each branch. (See Fig. 6)
Step 7. Plug the well-connected power cord from the tree section (C)
into a proper outlet.
Pre-Assembly
Assembly

Step 8. Please note this tree comes with a foot pedal switch and a
remote control for easy illumination and changing functions.
This treeis Color Changing,the8 lighting options available are:
1.Steady Warm White
2.Flashing Warm White
3.Fade In and Fade Out Warm White
4. Steady Multicolor
5. Flashing Multicolor
6.Fade In and Fade Out Multicolor
7.Sequential Multicolor & Warm White
8.Color Changing
These functions can be changed by pressing the foot pedal
switch or using the remote control. Please see the instructions
of remote control below.
Turning on the tree
Step 1. Plug the well-connected powercordfrom the tree section (C) into
a proper outlet.
Step 2. Press theremote controlor footpedal switchto choosefunctions.
Instructions of Remote Control
Please note this tree has a remote control.
Pleasepull out theinsulationtapefrom the remote control, before starting
to use it.
1. Press Fn button, the function below cycle. Press the number key,
select from the following corresponding lighting functions:
Function 1: Steady Warm White
Function 2: Flashing Warm White
Function 3: Fade In and Fade Out Warm White
Function 4: Steady Multicolor
Function 5: Flashing Multicolor
Function 6: Fade In and Fade Out Multicolor
Function 7: Sequential Multicolor & Warm White
Function 8: Color Changing
If the remote control does not work, check whether the battery of the
remote control is out of power.
To replace the remote control battery:
1. Replace with a new button cell “CR2025” (3 volt) into
the compartment.
CAUTION: DO NOT DISPOSE OF
BATTERIES IN FIRE. BATTERIES MAY EXPLODE
OR LEAK.
CAUTION:
1. Theproductconsistsofnon-replaceableLEDlamps.Toreducethe
risk of fire or electric shock, do not attempt to replace lamps or
modify string.
2. If a branch of the tree falls off, reinstallit with a spare latch (G).
3. This product can only be used with the original adapter, not other
brands of adapter.
Care and Cleaning
Step 1. Before using or reusing, inspect product carefully. Discard any
productthathavecut,damaged,orfrayedwireinsulationorcords,
cracks in the lampholders or enclosures, loose connections, or
exposed copper wire.
Step 2. When storing the product, carefully remove the product from
whereveritisplaced,includingtree,branches,orbushes,toavoid
any undue strain or stress on the product conductors,
connections, and wires. Remove all ornaments and decorations.
Step 3. Unplug the cord from the wall outlet and then disconnect each
sectionofthetree.Removethepowercordsfromthetreebottom
(C).
Step4.Gentlyliftthetreetopstraightuptoremovefromthecentersection
and fold all branches towards the pole.
Step 5. Repeat this step for the center and bottom tree sections.
Step 6. Carefully place all tree sections into a shipping box and tape it
shut.
Step 7. Store your tree in a cool, dry place away from sunlight.
Troubleshooting
Problem
Solution
The tree
does not
light
Ensure that all tree sections are connected into each
other well by pressing each section down and rotating.
Ensure that the power cord is plugged into the hole of
the connector found on the tree bottom (C). Make sure
power cord plug is securely inserted into a working
electrical outlet.
If you are still experiencing problems with the tree
please call 1-877-527-0313 for instructions.
The device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions: (1) This
device may not cause harmful interference, and (2) this
device must accept any interference received, in
cluding
interference that may cause undesired operation.
Warning:
Please note that changes or modifications not
expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment.
NOTE:
This equipment has been tested and found to
comply with the limits for a Class B digital device, pursuant
to Part 15 of the FCC Rules.
These limits are designed to
provide reasonable protection against harmful interference
in a residential installation.
This equipment
generates, uses
and can radiate radio frequency energy and, if not installed
and used in accordance with the instructions, may cause
harmful interference to radio communications.
Operation

However, there is no guarantee that interference will not
occur in a parti
cular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and
on, the user is encouraged to try to correct the interference
by one or more of the following
measures:
-
Reorient or relocate the receiving antenna.
-
Increase the separation between the equipment and
receiver.
-
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
-
Consult the dealer or an experienced radio/TV technician
for help.
Importer: Home Depot
Address: 2455 PACES FERRY ROAD ATLANTA, GA 30339
Tel: 1
-877-527-0313
Adapter Model No. TS-12W12V