Home Accents Holiday 1006185191 User manual

Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a) READ AND FOLLOW ALL
SAFETY INSTRUCTIONS.
b) This product is for indoor use only. The electrical rating 0.4 A 120 V
60 Hz.
c) Do not use this product outdoors.
d) This seasonal use product is not intended for permanent installation
or use.
e)Donotmountorplaceneargasorelectricheaters,fireplace,candles
or other similar sources of heat.
f) Do not secure the wiring of the product with staples or nails, or place
on sharp hooks or nails.
g) Do not let lamps rest on the supply cord or on any wire.
h) Unplug the product when leaving the house, or when retiring for the
night, or if left unattended.
i) This is an electric product – not a toy! To avoid risk of fire, burns
personalinjury and electric shock itshouldnot be playedwithor placed
where small children can reach it.
j) Do not use this product for other than its intended use.
k) Do not hang ornaments or other objects from cord, wire, or light
string.
l) Do not close doors or windows on the product or extension cords as
this may damage the wire insulation.
m)Donot cover theproductwith cloth,paper or anymaterialnotpartof
the product when in use.
n) Do not move the tree by pulling the tree tips or tree branches.
o) This product contains an extension cord with a polarized plug (one
prong is wider than the other)as a feature to reduce the risk of
electrical shock. This plug will fit in a polarized outlet only one way. If
the plug does not fit fully in theoutlet, reverse the plug. If it still does
not fit, contact a qualified electrician. Do not use with an extension
cord unless plug can be fully inserted. Do not alter or replacethe
plug.
p)Thisproductisequippedwithpush-intypelamps.Donottwistlamps.
q) This product employs overload protection (fuse). A blown fuse
indicatesan overload or short-circuit situation. If the fuse blows, unplug
the product from the outlet. Also unplug any additional strings or
products that may be attached to the product. Replace the fuse as per
the user servicing instructions (follow product marking for proper fuse
rating) and check the product. If the replacement fuse blows, a
short-circuit may be present and the product should be discarded.
r) Read and follow all instructions that are on the product or provided
with the product.
s) SAVE THESE INSTRUCTIONS.
CAUTION!– ALWAYS UNPLUG YOUR
TREE FROM ITS POWER SOURCE BEFORE
ASSEMBLING OR DISASSEMBLING.
7.5ft Hogan Fir with LED Warm White Tree
SKU# 1006185191
Package Contents
A. Tree top
Qty: 1
B. Tree center
Qty:1
C. Tree bottom Qty:1
D. Stand with an
eye bolt
Qty: 1
E. Power supply
cord
Qty: 1
F. Replacement
Bulb
Qty: 8
G. Fuse
Qty: 2
H. Latch
Qty: 2
Assembling the tree stand
Step 1. Choose a location near a wall outlet.
Step2. Open thestand to a 90 degreeangleuntil the hole linesup with the
hole on the tube.
Step 3. Screw an eye bolt into the hole.
Assembling the tree
Pleaseremoveprotectivecoversfromthe baseofthepoleforeachtree
section before assembling.
Step1. Carefully insert bottom section (C) of tree into tree base and
tighten the screw. (See Fig. 1)
Step2.Insertthemiddlesection(B)ofthetreeintothebottomsection(C).
(See Fig. 2)
Step 3. Insert the top section (A) into the middle section (B). (See Fig. 3)
Step4. Allow branches to fall into place or gently pull branches up andout.
When adjusting branches be sure that all wires are free of branch
hinges. (See Fig. 4)
Step 5. Shape the branches. Starting with tips closest to the pole, shape
onetip totheright,one to the left andone at the centerof themain
stem. Repeat pattern for each branch. (See Fig. 5)
Step6. Plug thewell-connected powercord fromthe treesection (C) into
a proper outlet. Please note this tree comes with a foot pedal
switch for easy illumination.
Pre-Assembly
Assembly

Turning on the tree
Step 1. Plug the well-connected power cord from the tree section (C)
into a proper outlet.
Replace the fuse.
1. Fuse replacement of powersupply cord from bottom section (C)
(replaceable 3 amp, 125 voltfuse is located in spare parts bag):
a) Grasp plug and remove from the receptacle or other outlet
device. Do not unplug by pulling on cord.
b) Open fuse cover. Slide open fuse access
cover on top of attachment plug towards
blades.
c) Remove fuse carefully.
d) Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse
(provided with product).
e) Close fuse cover. Slide closed the fuse access cover on top of
attachment plug.
f) Risk of fire. Do not replace attachment plug. Contains a safety
device(fuse) thatshouldnot be removed.Discardproductifthe
attachment plug is damaged.
2. Fuse replacement of power supply extension cord with foot pedal
switch (replaceable 5 amp, 125 volt fuse is located in the plug):
Thisplugwillfit ina polarizedoutletonlyoneway. Ifthe plugdoes
not fit fully in the outlet, reverse the plug. If it still doesnot fit,
contact a qualified electrician. Do not use with an extension cord
unless plug can be fully inserted. Do notalter or replace the plug.
a) Grasp plug and remove from the receptacle or other outlet
device. Do not unplug by pulling on cord.
b) Open fuse cover. Slide open fuse access
cover on top of attachment plug towards
blades.
c) Remove fuse carefully.
d) Risk of fire. Replace fuse only with 5 Amp, 125 Volt fuse
(provided with product).
e) Close fuse cover. Slide closed the fuse access cover on top of
attachment plug.
f) Risk of fire. Do not replace attachment plug. Contains a safety
device(fuse) thatshouldnot be removed.Discardproductifthe
attachment plug is damaged.
Replace the lamp.
a) Graspplugandremovefromthereceptacleorotheroutletdevice.Do
not unplug by pulling on cord.
b) Unlock the burned out LED bulb by lifting the hook and pulling both
the bulb and plastic base straight out of the bulb holder. Do not twist
bulbs.
c) Replace burned out bulb with 3.0 volt, 20 mA LED type bulb ONLY.
(Replacement bulbs included)
d) Lock the LED bulb.
CAUTION
1. To reduce the risk of overheating, replace burned-out lamps promptly.
Use 3.0 Volt, 20 mA LED lamps only.
2. Riskoffire.Thisproductdoesnotcontainlampshunts,whichallowthe
product to operate if one lamp burns out. Replace lamps only with the
spare lamps provided with this product.
If the new lamp base does not fit in lampholder, follow the steps below
before step c.
1. Pull the reflector out.
2. Remove the base of burned out lamp by straightening lamp leads
and gently pulling lamp out.
3. Thread leads of new lamp through hole
in old base with one lead in each hole
(alwaysmatchthelong lead ofnew lamp
to the hook of lamp base.)
4. After bulb is fully inserted, bend each lead up so that the leads will
touch the contacts inside the bulb holder.
5. Insert the reflector into the base.
CAUTION! – ALWAYS UNPLUG YOUR TREE FROM ITS
POWER SOURCE BEFORE ATTEMPTING FUSE AND BULB
REPLACEMENT.
Care and Cleaning
Step 1. Remove all ornaments and decorations.
Step 2. Unplug the cord from the wall outlet.
Step3. Gentlylift thetreetopstraight uptoremovefromthe centersection
and fold all branches towards the pole.
Step 4. Repeat this step for the center and bottom tree sections.
Step5. Carefullyplacealltreesectionsintoashippingboxandtapeitshut.
Step 6. Store your tree in a cool, dry place away from sunlight.
Use and Care Instructions
a) Before using or reusing, inspect product carefully. Discard any
productsthathavecut,damaged,orfrayedwire insulationorcords,
cracks in the lampholders or enclosures, loose connections, or
exposed copper wire.
b) When storing the product, carefully remove the product from
wherever it is placed, including tree, branches, or bushes, to avoid
any undue strain or stress onthe product conductors, connections,
and wires.
c) When not in use, store neatly in a cool, dry location protected from
sunlight.
Operation
Maintenance

CAUTION
a) Toreduce theriskof electricshock,use only with the power-supply
cord provided or with a cord set intended for outdoor use.
b) Do not use a cracked, frayed, or damaged cord. Inspect the cord
periodically.
c) Donotabusecord–Donotcarryproductbythecordoryankorpull
it to disconnect from the outlet.
d) Disconnect the product from the outlet when not in use.
Troubleshooting
Problem
Solution
The tree
does not
light
Ensure that all tree sections are connected into each
other well. Make sure the plug of power supply
extension cord from the bottom section (C) is securely
inserted into a working electrical outlet.
Check for blown fuses at the power cord plug. Replace
as needed with the replacement fuses provided.
Check for loose, broken, or missing bulbs and replace
as needed with the replacement bulbs provided.
If you are still experiencing problems with the tree
please call 1-877-527-0313 for instructions.
Loose branches
If a branch of the tree falls off, follow the steps below to reinstall it with a
spare latch (H).
1) Place the branch into the slot of the bracket.
2) Insert a spare latch through
the hole and use diagonal
pliers (not included) to crimp
the latch. (See Fig. A)
Model No. LTW38-4A