Home Decorators Collection 1004213746 User manual

Safety Information
IMPORTANT SAFETY
INSTRUCTIONS
When using electrical products, basic precautions should always be
followed including the following:
a) READ AND FOLLOW ALL SAFETY
INSTRUCTIONS.
b) This product is for indoor use only. The electrical rating 3.0 A 120 V 60
Hz.
c) Do not use seasonal products outdoors unless marked suitable for
indoor and outdoor use. When products are used in outdoor applications,
connect the product to a Ground Fault Circuit Interrupting (GFCI) outlet. If
one is not provided, contact a qualified electrician for proper installation.
d)This seasonal use product is not intended for permanent installation or
use.
e)Do not mount or place near gas or electric heaters, fireplace, candles or
other similar sources of heat.
f)Do not secure the wiring of the product with staples or nails, or place on
sharp hooks or nails.
g)Do not let lamps rest on the supply cord or on any wire.
h)Unplug the product when leaving the house, when retiring for the night,
or if left unattended.
i)Thisisanelectricproduct–notatoy! Toavoidriskoffire, burnspersonal
injury and electric shock it should not be played with or placed where small
children can reach it.
j)Do not use this product for other than its intended use.
k)Do not hang ornaments or other objects from cord, wire, or light string.
l)Do not close doors or windows on the product or extension cords as this
may damage the wire insulation.
m)Do not coverthe product with cloth, paperor any material not part ofthe
product when in use.
n) Do not move the tree by pulling the tree tips or tree branches.
o) Read and follow all instructions that are on the product or provided with
the product.
p) SAVE THESE INSTRUCTIONS.
CAUTION! – ALWAYS UNPLUG YOUR TREE
FROM ITS POWER SOURCE BEFORE ASSEMBLING OR
DISASSEMBLING.
CAUTION
1. The product consists of non-replaceable LEDlamps. To reduce the
riskoffireorelectricshock,donotattemptto replacelampsor modify
string.
2. This product can only be used with the original adapter, not other
brands of adapter.
9ft 10000L Cavalier Frasier Fir Color Changing
Micro Dot with 8 Function
SKU# 1004213746
Package Contents
A. Top Section
Qty: 1
B. Upper Middle
Section
Qty: 1
C. Middle
Section
Qty: 1
D.Lower Middle
Section
Qty: 1
E. Tree Bottom
Qty: 1
F. Stand with an
eye bolts
Qty: 1
G. Power Cord
Qty: 1
H. Remote
control
Qty: 1
I. Latch
Qty: 2
J. Threaded iron
latch
Qty: 2
K. Retainer
washer
Qty: 4
Assembly
Assembling the tree stand
Step 1. Choose a location near a wall outlet.
Step 2. Open the stand to a 90 degree angle until the holelines up with the
hole on the tube.
Step 3. Screw an eye bolt into the hole.
Pre-Assembly

Assembling the tree
Please remove protective covers from the base of the pole for each tree
section before assembling.
Step 1. Insert tree bottom (E) into the tree stand and tighten the screw.
(See Fig. 1)
Step 2. Insertlowermiddlesection(D)intothetreebottom(E).(SeeFig.2)
Step3. Insertthemiddlesection (C)intothelower middlesection (D).(See
Fig. 3)
Step 4 Insert upper middle section (B) into the middle section (C). (See
Fig. 4)
Step 5. Insert tree top (A) into the upper middle section (B). (See Fig. 5)
Step 6. Insert the provided power cord into the connector on the tree
bottom (E) in right direction properly and tightly (always match the
protuberance of the end connector of power cord to the concave
of the connector found on the tree bottom (E) according to the
magnified drawing on fig. 6.).
Step 7. Allow branches to fall into place or gently pull branches up and out.
When adjusting branches be sure that all wires are free of branch
hinges. (See Fig. 7)
Step 8. Shape the branches. Starting with tips closest to the pole, shape
one tip to theright, one to the left and one at the center ofthe main
stem. Repeat pattern for each branch. (See Fig. 8)
Step 9. Plug the power cord into a proper outlet. This tree comes with a
control box and a remote control for easy illumination and
changing functions. This tree is Color Changing, the 8 lighting
options available are:
1.Steady Warm White
2.Flashing Warm White
3.Fade In and Fade Out Warm White
4.Steady Multicolor
5.Flashing Multicolor
6.Fade In and Fade Out Multicolor
7.Sequential Multicolor & Warm White
8.Color Changing
These functions can be changed by using control box or remote
control.
Please seeInstructions of control box and remote control as
below.
Operation
Turning on the tree
Step 1. Connect each tree section well and plug the well-connected power
cord into a wall outlet.
Instruction of control box and remote
control
Instruction of control box
1. Press the ON/OFF button on control box to turn on and off the tree
lights.
2. Press the MODE button on control box to select below functions:
1.Steady Warm White
2.Flashing Warm White
3.Fade In and Fade Out Warm White
4.Steady Multicolor
5.Flashing Multicolor
6.Fade In and Fade Out Multicolor
7.Sequential Multicolor & Warm White
8.Color Changing
3. In the state of function 2, 3, 5, 6, 7 or 8:
presstheSPEED+button,thespeedofthecorrespondingfunctionis
faster.
presstheSPEED- button, the speed ofthe corresponding function is
slower.
There is memory mode on functions whether the tree is re-started.
It has Output Short-circuit Protection
When the load is short-circuited, the output can be automatically
closed. After eliminating the short circuit and restarting the power on,
it can return to normal.
Instruction of remote control
Please note this tree has a remote control.
Please pull out the insulation tape from the remote control, before starting
to use it.
1. Press Fn button, the function below cycle. Press the number key,
select from the following corresponding lighting functions:
Function 1: Steady Warm White
Function 2: Flashing Warm White
Function 3: Fade In and Fade Out Warm White
Function 4: Steady Multicolor
Function 5: Flashing Multicolor
Function 6: Fade In and Fade Out Multicolor
Function 7: Sequential Multicolor & Warm White
Function 8: Color Changing
If the remote control does not work, check whether the battery of the
remote control is out of power.
To replace the remote control battery:
1. Replace with a new button cell “CR2025” (3 volt)
into the compartment.
CAUTION: DO NOT DISPOSE OF
BATTERIES IN FIRE. BATTERIES MAY EXPLODE
OR LEAK.
Vents

Care and Cleaning
Step 1. Before using or reusing, inspect product carefully. Discard any
productthathavecut , damaged,or frayed wireinsulation or cords,
cracks in the lampholders or enclosures, loose connections, or
exposed copper wire.
Step 2. When storing the product, carefully remove the product from
wherever it is placed, including tree, branches, or bushes, to avoid
any undue strain or stress on theproduct conductors, connections,
and wires. Remove all ornaments and decorations.
Step 3. Unplug the power cord from the wall outlet. And remove your
power cord from tree bottom (E) and save them.
Step 4. Gentlyliftthe treetop straightuptoremovefrom the centersection
and fold all branches towards the pole.
Step 5. Repeat this step for the center and bottom tree sections.
Step 6. Carefullyplace alltree sectionsintoa shippingboxandtape itshut.
Step 7. Store your tree in a cool, dry place away from sunlight.
Troubleshooting
Problem
Solution
The tree
does not
light
Ensure that all tree sections are connected into each
other well by pressing each section down and rotating.
Make sure the power cord is wellconnected to the tree
bottom (E) and that the tree is plugged into the wall
outlet..
Ifyou are stillexperiencingproblemswiththe treeplease
call 1-877-527-0313 for instructions.
Loose branches
1. If a branch of the tree in section A, B or C falls off, follow the steps
below to reinstall it with a spare latch (I).
1) Place the branch into the slot of the bracket.
2) Insert a spare latch
through the hole and
use diagonal pliers
(not included) to
crimp the latch. (See
Fig. A)
2. Ifabranchofthetreeinsection D or Efallsoff, followthestepsbelow
to reinstall it with a spare threaded iron latch (J) and two retainer
washers (K).
1) Place the branch into the slot of the bracket.
2) Insert a spare threaded
iron latch (J) through the
hole and secure using
two retainer washers (K).
(See Fig. B)
The device complies with Part 15 of the FCC Rules. Operation
is subject to the following two conditions: (1) This device may
not cause harmful interference, and (2) this device must
accept any interference received, including interference that
may cause undesired operation.
Warning: Please note that changes or modifications
not expressly approved by the party responsible for
compliance could void the user’s authority to operate the
equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15
of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by
one or more of the following measures:
●Reorient or relocate the receiving antenna.
●Increase the separation between the equipment and
receiver.
●Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
●Consult the dealer or an experienced radio/TV technician
for help.
Importer: Home Depot
Address: 2455 PACES FERRY ROAD ATLANTA, GA 30339
Tel: [phone]
Adapter Model No. RHD75W240300